wayground logo

Free Printable Worksheets

NEW

Font size

S
M
L
XL
Worksheets

Weekly Quiz ENGINE PERFORMANCE 3/17/2022

Total questions: 20

Worksheet time: 15mins

Name
Class
Date
1.

When the top of the piston outside diameter is machined slightly smaller than the bottom, it is called a

a)

pop-up piston

b)

dished piston

c)

cam-ground piston

d)

piston taper

2.

Which of the following is not a basic part of an engine bottom end?

a)

block

b)

valve train

c)

crankshaft

d)

connecting rods

3.

Which of the following does not relate to modern piston assemblies?

a)

Full-floating pin.

b)

Press-fit pin.

c)

Bolted piston pin.

d)

Offset piston pin.

4.

The most efficient air/fuel mixture is

a)

12.6:1

b)

14.7:1

c)

18.5:1

d)

20.4:1

5.

A multi-port fuel injection system

a)

injects fuel through the air induction system

b)

injects fuel into the intake manifold near the valve

c)

uses a choke plate for cold weather operation

d)

distributes fuel through the throttle body

6.

The vertical axis on the oscilloscope screen represents

a)

ohms

b)

amperage

c)

voltage

d)

time

7.

The purpose of the ignition coil is to

a)

lower the ignition system current draw

b)

reduce the battery voltage

c)

increase the amperage at the plugs

d)

step up voltage to fire the plugs

8.

The distributorless ignition coil pack will fire

a)

two plugs at the same time

b)

one plug at a time

c)

two plugs at different times

d)

three plugs at the same time on a V-6 engine

9.

The MAJOR cause of an exhaust system rusting is

a)

long trips

b)

short trips

c)

low speed driving

d)

high speed driving

10.

A leaky exhaust system could cause

a)

excessive noise

b)

excessive emissions

c)

danger for the driver and passenger

d)

all of the above

11.

The device used to control alternator field current is the

a)

diode trio

b)

stator

c)

rectifier bridge

d)

voltage regulator

12.

Before testing a charging system, the vehicle must have

a)

a fully charge battery

b)

a well-tuned engine

c)

proper ignition timing

d)

a discharged battery

13.

Alternator diodes are used to convert

a)

AC to DC

b)

DC to AC

c)

mechanical energy to electrical energy

d)

electrical energy to mechanical energy

14.

An indication of alternator output can be obtained by

a)

verifying that the alternator is grounded

b)

comparing battery voltage with the engine off and engine running

c)

cranking the starter for 15 seconds

d)

Load testing for 15 seconds

15.

If three lamps of 2 Ohms, 6 Ohms and 10 Ohms are connected in series, their total resistance value in Ohms is

a)

6 Ohms

b)

9 Ohms

c)

12 Ohms

d)

18 Ohms

16.

When replacing a open(blown)fuse,

a)

one of a higher capacity is acceptable

b)

one of the same capacity should be used

c)

one of a lesser capacity is preferred

d)

a jumper wire can be substituted

17.

When replacing electrical components,

a)

disconnect the battery ground cable

b)

disable the ignition system

c)

use only insulated wrenches

d)

isolate the alternator to prevent damage

18.

What supplies energy in an electric

circuit?

a)

conductor

b)

light bulb

c)

battery

19.

Which type of circuit is Circuit A?

a)

series

b)

parallel

c)

perpendicular

20.

What type of circuit is shown in the picture?

a)

Series Circuit

b)

Broken Circuit

c)

Parallel Circuit

d)

Open Circuit