wayground logo

Free Printable Worksheets

NEW

Font size

S
M
L
XL
Worksheets

155 inspect vehicles

Total questions: 54

Worksheet time: 27mins

Name
Class
Date
1.

which of the following is checked on an MOT test

a)

Torque

b)

Headlight alignment

c)

impact damage

d)

BHP

2.

A new vehicle is going out to a customer but before it does what inspection is carried out

a)

Post delivery inspection

b)

Final delivery inspection

c)

Pre delivery inspection

d)

interim delivery inspection

3.

After a vehicle is serviced the vehicle pulls to the left, what is the cause of this

a)

wheels out of balance

b)

wheel alignment incorrect

c)

Brake failure

d)

handbrake stuck on

4.

An inspection of an alternator on a service inspection will check

a)

resistance of alternator windings

b)

maximum regulated voltage

c)

wiring of alternator

d)

alternator recommended output

5.

Blue smoke coming from the exhaust could be caused by

a)

stuck valve

b)

worn piston rings

c)

coolant leak

d)

faulty fuel injector

6.

What component is fitted inside of the vehicle

a)

air filter

b)

fuel filter

c)

oil filter

d)

pollen filter

7.

positive wheel toe makes the wheel point in the following direction

a)

inwards

b)

outwards

c)

straight ahead

d)

to one side

8.

what does the the following image allow the vehicle to carry out

a)

go straight ahead

b)

allow the one wheel to turn at a greater radius from the other when cornering

c)

allow both wheels to turn together

d)

lock from wheels

9.

When testing with a hydrometer what reading is for a fully charged battery

a)

1.265-1.280

b)

1.300-1.360

c)

1.200-1.240

d)

1.100-1.180

10.

looking at the image how can you access if the tyre is illegal for use on the road

a)

tread depth pattern

b)

tyre size

c)

tread wear indicators

d)

Tread wear average

11.

1. Which of the following tasks is usually carried out by the service reception following routine maintenance?

a)

Complete the in-vehicle service history

b)

Calculate the customer's invoice charges

c)

Correctly re-instate any components and fittings

d)

Check for signs of grease on paintwork surfaces

12.

The aspect ratio of a tyre is the:

a)

width of a tyre expressed in millimeters

b)

circumference of a tyre expressed in inches

c)

maximum height of a tyre expressed in millimeters

d)

height of the tyre expressed as a percentage of the width

13.

Headlights very bright, battery gassing heavily.

a)

Alternator Drive Belt

b)

Car Battery

c)

Voltage Regulator

d)

Alternator Rectifier

14.

Car submitted for a MOT, tire excessively low.

a)

Do the test, but fail it.

b)

Refuse to do the test until the tire is fixed.

c)

Replace the tire before the test.

15.

What would need to be replaced if this was leaking ?

a)

brake disc

b)

brake pad

c)

brake shoe

d)

brake drum

16.

Which components would fail, if this component breaks.

a)

Camshaft and Valves

b)

Battery and air conditioning

c)

Thermostat and cooling

d)

electric power steering and heating

17.

Car is low and sits on one side.

a)

Dampers

b)

Suspension coil springs

18.

Manual gear box is being inspected , what would you check for

a)

gear are changing automatically

b)

clutch is functioning correctly

c)

makes the outer turn faster than the inner

d)

makes the inner turn faster than the outer

19.

At what temperature does the thermostat start to open

a)

60

b)

78

c)

90

d)

100

20.

excessive white smoke is coming from the exhaust , what is the fault

a)

piston rings worn

b)

valve seal worn

c)

Head gasket failure

d)

timing belt failure

21.

The bottom ball joint is worn what will be affected

a)

toe out

b)

toe in

c)

camber angle

d)

toe out on turns

22.

When are the brake drums removed for inspection

a)

Mot inspection

b)

annual service

c)

small service

d)

interim service

23.

The brake pads are worn at 10%, what would you do

a)

Inform the customer

b)

fit new shoes

c)

strip down brakes and find the problem

d)

Change the brake pads

24.

What would be the result if the wheel imbalance was not corrected

a)

premature wear of steering wheel

b)

steering heavy

c)

metal fatigue on the wishbone

d)

premature damper failure

25.

when would you inform the customer of a fault in a tyre

a)

25mm with cords showing

b)

5mm cut

c)

underinflated tyre

d)

incorrect make of tyre

26.

On an MOT test which of the following is checked

a)

tyre pressure

b)

fuel level

c)

head light alignment

d)

car radio reception

27.

what is the mirror on top of the headlight alignment used for?

a)

for the technician to see inside the vehicle

b)

to check main beam

c)

reflect so the technician can see

d)

to shine more light so you can see clearly.

28.

what would a blocked fuel filter cause?

a)

contaminated coolant

b)

electric fuel pump

c)

power loss

d)

oil leakage

29.

if the front bumper was damaged, what would you check for?

a)

check front alignment or headlight

b)

to fix the bumper as soon as possible

c)

to check the engine

d)

ensure tyre pressure is accurate

30.

how does a technician obtain a P code from a vehicle

a)

use a diagnostic scanner

b)

use a power probe

c)

use a laptop

d)

use a multimeter

31.

how would you check a CI (diesel) engines emissions?

a)

when the engines hot

b)

at 7000 revs

c)

when the engine is running

d)

when the engine is at idle

32.

when is the VIN checked?

a)

pre inspection

b)

post inspection

c)

on a MOT test

d)

safety inspection

33.

What would you be testing from the following diagram

a)

side lights

b)

main beam

c)

headlight (dip beam)

d)

fog light

34.

inspection of differential gearing , you would check for

a)

mesh of gears

b)

pre -load

c)

re gapping

d)

oil change

35.

if the shown component makes lot of noise , what should the technician do

a)

check belt tension

b)

alternator bearings

c)

crankshaft

d)

mounting bolts

36.

what component is designed the same

a)

heater matrix and radiator

b)

serpentine belt and cambelt

c)

cylinder head and block

d)

camshaft and crankshaft

37.

which one of the following pulleys would you use for correctly tensioning the belt/timing

a)

injp

b)

injp

c)

idler

d)

tens

38.

Which of these can you detect an issue with by listening to it?

a)

Injector spray pattern

b)

water pump bearing

c)

Alternator

d)

Camshaft

39.

What is the equipment above used for, when caring out an MOT?

a)

Headlights

b)

Tyres

c)

Front Bumper Alignment

d)

Emissions

40.

Starter motor when turning over is making a noise, what is likely to be the fault?

a)

Solenoid

b)

Pulley

c)

Drive belt

d)

Ring gear

41.

What is the fault in the image shown?

a)

Steel bead damaged

b)

Sidewall cords damaged

c)

Tyre tread failure

d)

Over pressurized tyre

42.

What is the difference between Synthetic and Non-Synthetic oil?

a)

natural oil with no additives

b)

synthetic oil comes straight from the ground

c)

Synthectic oil does not last as long as non synthetic

d)

Synthetic oil is manmade with additives

43.

What could cause oil to be milky?

a)

Costa coffee spilt in the engine

b)

worn piston rings

c)

worn head gasket

d)

worn sump gasket

44.

When caring out an MOT inspection, you notice a cv boot is split, how could this affect the MOT test?

a)

Advise the fault

b)

Fail the DVSA test

c)

Do nothing

d)

Replace the components

45.

What would be the best action from finding the following fault?

a)

Replace the boot

b)

Replace driveshaft

c)

Clean, pack with grease and fit new boot

d)

Replace the steering gaiter

46.

Which type of tyre has its ply at a 90degrees to the bead?

a)

Radial

b)

Cross Ply

47.

What would cause a flat patch on a tyre?

a)

Too much air pressure

b)

Too less air pressure

c)

Incorrect camber angle

d)

BURNOUTS

48.

What device would you use to identify a noise?

a)

Mechanics

Stephoscope

b)

Diagnostic Scanner

c)

Osicilloscope

49.

What bulbs could be used for a Front side light?

a)

5W and Led

b)

55W and Led

c)

Halogen and Led

d)

Neon and Led

50.

A post Cat-Converter was delivering 0.5Volts. What does this mean?

a)

Blocked air filter

b)

Emissions are incorrect

c)

Catalytic Converter Blocked

d)

Post Catalytic conveter

51.

How is a Bubble formed in a tyre wall?

a)

Potholes

b)

Curbs

c)

Sidewall cords damaged

52.

What is the max limit for cuts or rips on a tyre?

a)

25mm & Showing Cords

b)

20mm

c)

10mm & Showing Cords

d)

5mm

53.

What is assessed on a MOT test?

a)

Headlight Aim

b)

Speed Test

c)

Road Test

d)

Service

54.

When are brake drums removed?

a)

MOT

b)

Interim Annual Service

c)

Major Annual Service

d)

Minor Annual Service