NEW
Font size
WorksheetsTampo Training Module A 2
Total questions: 10
Worksheet time: 20mins
Which condition below present during “Distortion” Offset 以下哪种情况会出现在“胶头变形”的图案偏移？
A.Not use same rubber type as during graphic development.
生产时所用的胶头与第一次图案研发时使用的胶头不相同
B. Graphic image registration offset.
图案本身定位偏移
C. Rubber not in same position as during graphic development.
生产时胶头的位置与第一次图案研发时的位置不一样
D.( A ) ( C ) correct.
( A ) ( C ) 都正确
E. ( A ) ( B ) ( C ) correct.
( A ) ( B ) ( C ) 皆正确
What is the correct method to solve alignment problem permanently on head light ? 什么是解决车灯偏移问题的正确方法？
A. Shift Graphic Registration
改动图案位置
B. Recalibrate Tampo Machine
重新调校移印机器
C. Follow Setup info of Rubber type & Rubber position same as during Graphic development.
完全依照第一次图案研发时的胶头和位置
D. Try other Rubber Type one after another, until alignment ok.
尝试不同类型的胶头，直到对位正确
E. All above correct
以上选项皆正确
Why knowing Product Acceptance Tolerance for print offset is important ? 为什么了解我们产品的验收公差对移印很重要?
A.Guidance for setting of acceptance tolerance to Line tooling & Production Fixture
给予生产线机器与夹具可接受的公差指南
B. Guidance for replacement of Machine Worn-out parts.
给予机器磨损部件更换的指南
C. Guidance for Machine acceptance buy-off after Preventive Maintenance
从PM处返回的机器，工程师针对其验收的指南
D. ( A ) ( C ) correct
A和C是正确
E. ( A ) ( B ) ( C ) correct
A、B、C皆正确
Magnitude of Print Offset on Final Toy product =
degree of inaccuracy at each indexing step of machine
玩具成品的移印总公差=机器运行的偏差程度
+ degree of worn-out of dimensional critical Machine part
机件的磨损程度
+ degree of inaccuracy of Nest Fixture
模具的不精准程度
+ degree of inaccuracy of fixture adaptor
夹具的不精准程度
+ degree of inaccuracy of component part
胶件的不精准程度
TRUE 正确
FALSE 错误
Which Sub Tampo Division below play key role in “Integrating” all critical Tampo Setup information before actual Production Run ?
在研发后以下哪一个移印小部门扮演着“整合”所有移印设置的重要信息之角色？
A.Nest Fixture / Epoxy Nest Making Division
夹具制作小部门
B.Rubber Pad Making Division
胶头制作小部门
C.Graphic Development Division
图案研发小部门
D.Tampo Machine Setup Division
移印机器设置小部门
E.Graphic Plate Making Division
钢板制作小部门
Which stated below are critical for setting up SMED / Dead-on Tampo Machine ?
下列哪项对SMED要求/Dead-on移印机器至关重要?
A.Center reference axis where “Ink pick-up” task happened
胶头取油墨的中心参考轴
B.Center reference axis where “printing” task happened
“打印”任务发生时的中心参考轴
C.Moving Distance of Rubber Pad Module
胶头模块移动距离
D.( A ) ( B ) correct
A和B都正确
E.( A ) ( B ) ( C ) correct
A、B、C皆正确
Which items below are calibration kit that work to ensure consistent
artwork distorted pattern between different machine ? 以下哪一项校准套件是用于确保扭曲图案不会发生在不同机器上？
D.( A ) ( C ) correct
A 和C都正确
E.( B ) ( C ) correct
B和C都正确
Which statement below WRONGLY described Images (M) & Image (N) below ?
下面哪一项说明错误描述图案（M）和图案（N）？
A.Image (M) is outcome of calibration method for Offset due to Distorted Artwork
图像(M)是由于胶头变形而产生的偏移量校准方法的结果
B.Image (M) is outcome of calibration method for “Whole Graphic” Offset
图像（M）是“全图形”偏移量校准方法的结果
C.Image (N) is outcome of Calibration method for “Color to Color” Offset
图像（N）是“色对色”偏移量校准方法的结果
D.Whole Graphic Offset can be accepted , if B smaller or equal to ( A + 0.1mm )
如果B小于或等于（A+0.1mm），则可以接受整个图形偏移
E.Color to Color Offset Must be rejected, if Y > ( X + 0.1mm )
如果Y > (X + 0.1mm)，则色对色的偏移必须被拒绝
Which image below correctly describe setup for Plate Making equipment & Other New Tampo Machines it should be ?
以下哪个图案准确描述制作钢板机器和其它移印机器需有的设置？
E All above correct
以上选项皆正确
Which statement are correct describing the print for “Orange color” Roof Top as highlighted ?
哪一个说明是正确描述“橙色”打印部分？
C Pin holes defect due to air trap is a common defect for this graphic, if rubber shape was not chose correctly
如果胶头的形状选择不符合，就会导致空气渗透到油墨中而产生针孔缺陷
D.( A ) ( C ) correct
A和C都正确
E.( B ) ( C ) correct
B和C都正确
