2. A rigid conduit connecting to an outlet box should have a _________.

3. Identified, as used in the Code in reference to a conductor or its terminal, means that such a conductor or terminal is to be recognized as ____________.

4. A toaster will produce less heat on low voltage because ______________.

5. If the current flow through a conductor is increased, the magnetic field around the conductor _____________.

6. Comparing a #6 to a #10 conductor of equal lengths, the #6 will have lower ________.

7. The definition of ambient temperature is _____________.

8. The primary reason for using a hacksaw blade with fine teeth rather than coarse teeth when cutting large stranded conductors is _____________.

9. The stranded residential service is a 3-wire, 240 volt single-phase system. The maximum voltage to ground in this system would be __________ volts.

10. When working on a motor, the electrician should ____ to prevent accidental starting of the motor.

11. It is the responsibility of the electrician to make sure his tools are in good condition because ___.

12. Continually overloading a conductor is a poor practice because it causes ___________.

13. For better illumination you would __________.

14. A junction box above a lay-in ceiling is considered _________.

15. Which of the following metals is most commonly used in the filament of a bulb?

16. Electrical equipment can be defined as ______________.

I. Fittings

II. Appliances

III. Devices

IV. Fixtures

17. If two equal resistance conductors are connected in parallel, the resistance of the two conductors is equal to ____________.

18. Wire connections should encircle binding posts in the ______ manner the nut turns to tighten.

19. Which of the following is a limit switch?

20. The primary and secondary windings of a transformer always have __________.

21. Which of the following is not the force which moves electron?

22. A motor with a wide speed range is a __________.

23. The “stator” of an AC generator is another name for the ____________.

24. Where galvanized conduit is used, the main purpose of the galvanizing is _________.

25. To lubricate a motor sleeve bearing you would use ___________.

26. When soldering conductors, flux is used ___________.

27. _____ means so constructed or protected that exposure to the weather will not interfere with successful operation.

28. The current used for charging storage batteries is ___________.

29. You should close a knife switch firmly and rapidly as there will be less ___________.

30. If one complete cycle occurs in 1/30 of a second, the frequency is ____________.

31. An instrument that measures electrical energy is called the ___________.

32. In electrical wiring, “wire nuts” are used to ___________.

33. Which of the following would be the best metal for a magnet?

34. An electrician may use a megger _____________.

35. The least important thing in soldering two conductors together is to _____________.

36. The property of a circuit tending to prevent the flow of current and at the same time causing energy to be converted into heat is referred to as _____________.

37. Rigid conduit is generally secured to outlet boxes by ___________.

38. Which one of the following is not a safe practice when lifting heavy items?

39. A thermocouple will transform _________ into electricity.

40. In a residence the wall switch controlling the ceiling light is usually ____________.

41. A switch which opens automatically when the current exceeds a predetermined limit would be called a ______________.

42. A wattmeter is a combination of which two of the following meters?

I. Ammeter

II. Ohmmeter

III. Phase meter

IV. Volt meter

V. Power factor meter

43. What would the ohmmeter read?

44. Acid is not considered a good flux when soldering conductors because it ______________.

45. If the spring tension on a cartridge fuse clip is weak, the result most likely would be ___________.

46. The branch circuit loads specified by the Code for lighting and receptacles are considered ____.

47. The conductor with the highest insulation temperature rating is _____________.

48. After cutting a conduit, to remove the rough edges on both ends, the conduit ends should be ____.

49. To fasten a raceway to a solid concrete ceiling, you would use ___________.

50. A commutator of a generator should be cleaned with which of the following?