NEW
Font size
Worksheetsgwt
Total questions: 50
Worksheet time: 25mins
The primary objective of a self check programme
To be more familiar with the procedures in the workcentre
to know the limitations that the workcentre have
to promotoe a culture of open reporting and continual improvement where quality issues are openly addressed and given adequate attention
to ensure no NC in the coming audits
The self check workplan is to be endorsed by_______ or its equivalent
Unit QMR
Unit CO
Unit OC
Unit S3
which logistics RAM model should workcentres adopt to take into consideration the unique nature of their work?
Follow strictly to the RAM model as prescribed in the AFLO
no standardised RAM model format required
customised logistics RAM documented in the command logistics orders
follow strictly to the RAM model as preserbived in the rsaf safety management manual
Individual factors identified as high risk shall be mitigated even if the overall risk is assessed____.
low
medium
high
very high
Modifications are carried out on rsaf ground electronics and weapons systems and associated support and test equipment for the following purpose except
to meet new operational requirements
to introduce new components to replace unserviceable items
to improve safety, performance, reliability, and maintainability
to reduce operational cost, case production and facilitate servicing
For modifications where immediate compliance is required, eg. Modifications that affects safety or to fulfill immediate operational requirements. An out of committee approval may be granted by
comd aelg
dhael
chairman of gewmc
chairman of wessab
What are the four main elements in the RAM guide?
method man medium machine
management method medium machine
management man medium method
management man medium machine
Who are allowed to perform aircraft component removal/installation, servicing or maintenance
only qualified and authorized personnel
only air material specilist
any on the job trainee
anybody
Indepenndent checks or third party inspections are mandatory for critical aircraft systems to ensure
no loose or unsecure aircraft components is present
the job is closed properly
correct fitment, sense of direction and function
no unathorised personnel has worked on the aircraft
When multiple trades are required on the same job, what is required?
assign a prime workcentre to take charge
place appropriate warning signs orplacards to warm others of any potential dangers
conduct a final physical check before closing the job
all of the above
What are the details of the measurements taken should be recorded in the saf 1400
measurements of the final functional checks only
in process critical tasks as well as specifying reference to the relevant manuals only
measurements/data of the final functional checks as well as specifying reference to the relevant manuals only
measurements/data of the final functional checks and in process critical tasks as well as specifying reference to the relevant manuals
What information is required tp ne documented in the quality records of the equipment to establish that the final product has been inspected and tested
details showing clearly whether the equipment has passed or failed the rest should be sufficed
details showing that the tests were carriede out in accordance to the relevant technical manuals/publications should be sufficed
details showing clearly whether the equipment has passed or failed the test and reference to the technical manuals/publications is optimal
etails showing clearly whether the equipment has passed or failed the test and that the test was done i.a.w the relevant technical manuals/publications
serviceable reparable components shall be attached with a completed_____ post maintenance, inspection or testing
1431
1432
166
1911
Components removed for accesibility from the weapon systems or its next higher assembly shall be tagged with SAF 1911 which is a_______-
Unserviceable label
serviceable label
non repairable label
component holding label
For matters with potential impact to airworthiness/safety or component exceeding established allowable life extension limit, the approving authority is
CO of the flying sqn whose aircraft if affected
system/specialist branch heads
dhael or equivalanet in dsta
oc quality assurance centre
Long term concession may be granted for
instances where deviations from specific standards/requirements are due to factors beyond rsaf's control
instances when there's a lack of budget
instances when there is an urgent operational requirement to support
instances when the required component is our of stock and cannot be replenished
Originator of the servicing instruction is to review the findings of the SI and determine whether SI SHOULD BE REScinded or continued on a/an____ basis
weekly
monthly
quartely
annual
What is the diff between special techincal instruction and servicing instruction?
Special technical instruction is for non safety issue and servicing instruction is for safety related issues
Special technical instruction is reccuring and servicing instruction is non recurring
Special technical instruction is non reccuring and service instruction is reccuring
Special technical instruction is restricted to components only and servicing instruction is for aircraft
Defect reporting in rsaf is carried out to accomplish the following objectives:
to generate reliability and maintainability parameters, and form the basis of decision making in operational, maintenance, and/or engineering policies
to investigate and analyse the reported defects, and permit improvement to the maintenance and/or reliability of the weapon system
to enable deferment of defect rectification to meet operational requirements
all of the above
a defect is considered major when_______.
it will affect the safety of flight and/or compromise safety in ground operations
it will affect the safety of flight and/or compromise safety in ground operations and has fleet wide implications
it causes AOG
A defect which as minimal or no impact on the safety of flight and/or compromise safety in ground oeperations
a critical defect is
it will affect the safety of flight and compromise safety in ground operations
it will affect the safety of flight and compromise safety in ground operations and has fleet wide implications
it causes AOG
A defect which minimal or no impact on the safety of flight and compromise safety in ground operations
for those snr tech whose techinical currency on a system have lapsed for between 2 and 3 years, they can have their basic qst authorisation reinstated by
having woic interviewing the personnel
sitting and passing the relevant qst exam
having oc interviewing the personnel, sitting and passing the relevant qst exam
completing a customised ojt programmed stipulated by the unit co
with the qualified senior tech qualification status, one can perform
closing job by signing in the saf form 1400 workers(trademan) column only
closing job by signing in saf form 1400 both the workers(trademan) and supervisor column
approving and signing of all ADDs in the saf form 1400-3 (aircraft defect deferred log)
countersigning job done by a ojt
which of the following qualifications can be reinstated by obtaining a concession?
basic qt and qstt qualifications
advance and special qualifications
re-qualification of qt and qst after de-certification
all the above
the oic work centres may,after interview, is satisfied that the concerned aft, afe, omers, or avs is still competent although the re-authorisation pre-requistics are not met. A waiver of the requirement of re-authorisation should be submitted to___ for approval
unit co
head logs branch
oc flight
woic flight
for those aft,afe omers or avs who do not meet the reauthorization requirements, who shall interview the concerned personnel and decide on the need for re-training?
unit co
head logs branch
oc flight
woic flight
the re-authorisation period for the aft, afe, omers or avs is______
6month
9 monthly
12 monthly
as required by the basic quality assurance centrew
what is the main objective in maintaining traceability records of all critical TMDE
to enable the mangement to track the TMDE location
to enable the identification of all tasks that the out of calibrated tmde was used to service on
so that the tmde can be easily identified once the calibration due date is reached
so as to maintain a quality record
Only ctrical measurements require tmde traceability records. Such critically can be defined as:
when the tmde can only be calibrated by external agency
when the flight safety of aircraft systems can be affected by the inaccuracy of the tmde used
when there is no calibration report provided after the tmde has been calibrated
when there is only quantity one such tmde left in the unit
Who is the approving authority for excluding tmde. traceability requirements in critical measurements?
base maintenance centre
hlb/ co logistics units
relevant ae/se branch
aeld quality assurance branch
for proper tool identification, all tools, sub assemblies and accessories that are not rfid tagged are to be
colour coded
colour coded or engraved
colour coded or etched
colour coded, engraved or etched
a tools store is an enclosure dedicated for the storage of tools. the following requirements for the tools store shall be met:
.
very long anw
.
all of the above
all tools are to be inspected periodically for conditions. The min requirement for condition check and replacement when necessary is______ for tools
weekly
monthly
daily
annually
request for creation of new publication inventory account is to be approved by the respective unit's_________.
woic
oic
oc
co
afirc is to be updated within____ from the initiation date on any discrepancy found during publication inventory annual independent check
7 days
30 days
60 d
90 d
which may be issued by units as interim orders for maintenance procedures or engineering instructions for immediate compliance
maintenance information
local instruction
special technical instruction
servicing instruction
there is a requirement to document all interim/local instructions issued. these instructions are adhoc/interim maintenance procedures or engineering instructions for immediate compliance. And the instructions are kept in_____
local techinial order
local instruction folder
special techinical instruction
servicing instruction
maintenance records such as the saf 1400, which can be presented as evidence in a court of law, are to be retained_____
2 years after completion of work
3 year after records were closed
6 years after records were closed
permanently
which statements are true regarding entries made in manual records
cross out any erroneous entry and initialled by the person making the correction
all entries must be legible and made in ink or inedible pencil
no field or colukmn is to be left black. NA field are to be ruled off and indicated with "NA"
all of the above
with regards to filling of entries in the saf 1400g, which of the following practice are prohibited
signging on another trademan behalf
use of correction fluid or erasure of entries
use of red ink to cancel
all of the above
how should entries be cancelled or deleted on the f1400
errorneous entries are to be crossed out and signed for in blue or black ink only
pasting over, white over or over writing of entries to make correction is not allowed
a and b
the person making the cancellation is to place his signature above the certification
why is it important to report any incident/incident/hazards
to create awareness of the incident/accidnet and to inform/alert others to avoid making the same mistake
so that the incident/accident can be analysed and used for the purpose of accident prevention
a and b
none of the above
incident occurs between the time the pilot/aircrew accepts the aircraft for flightground run till the time he signs off the aircraft after flight/ground run, what type of report is this
gair
fair
aim
sor
which of the following configuration changge do not require GEWMC's approval
minor cots software upgrades and patches to address security vulnerabilities
changes in internal space usage
weighgt change and shift in centre of gravity
electrical load analysis
all techinical tasksmust be carried out
in the shortest possible time so as to accomplish the jobs
by reading at least oncee before commencing the jobs
with reference to technical checklist and maintenance manuals
with the help of with another qualified personnel
how are critical tasks defined in non-aircraft related workcentres
they are defined by the respective systems engineering/ air worthiness engineering centres/branches and documented in the CLO volume 3 of the respective work centres
they are defibed by the respective workcentres and documented in the aflo
they are defined by the respective systems engineering/airworthiness engineering centres/branches and documented in the aflo
unlike the aircraft related workcentres, theres no requirement to identify them
Local instruction shall have a recission date of
no longer than 14days
no longer than 3 months
no longer than 6 months
no longer than 12 months
which of the following examples could be reported under HAZARD report? lack of protective equipment, poor equipment design, discrepancies in application of aircraft working schedules, hazards air traffic routes, hazardous position of aircraft on dispersal
i and ii
i ii iii
iv v
all of the above
the following are some situational in which a fiar/gair must be submitted except:
when there's lessons to be learnt from the open reporting
to set the benchmark for disciplinning the errant personnel
when theres safety implications to continued operations
when there are serious injuries or fatalities that have resulted from the accident
Who is the approving authoriuty for destruction of all aircraft/weapon system related category b to e manual quality records beyond the retention periods stated in the aflo
comd aelgs
unit oc
quality assurance branch - aeld
no approval is required
