wayground logo

Free Printable Worksheets

Font size

S
M
L
XL
Worksheets

Woods 2a Final

Total questions: 55

Worksheet time: 5hrs 35mins

Name
Class
Date
1.

The safest way to remove scrap pieces from around the revolving blade is to:

a)

Turn off the power and wait for the blade to stop.

b)

Use a push stick

c)

Remove the stock being cut first,, before removing the chips

d)

Both A and B

2.

When crosscutting boards to a desired length on the tablesaw, a safe method to use is:

a)

The fence alone as a guide

b)

The first piece cut as a gauge

c)

A stop block clamped to the side of the fence as a guide

d)

Any of the above

3.
 Crosscutting of stock normally requires a:
a)
Fence
b)
Push Stick
c)
Stop Block
d)
Miter Gauge/Cross cut sled 
4.

When is it safe to do freehand (no fence, no miter gauge) sawing on the table saw?

a)

When cutting circles

b)

When cutting very thin stock

c)

Never

d)

When cutting plywood

5.
Is it safe to rip stock with the splitter in place?
a)
True
b)
False
6.

Which type of stock should never be ripped on the table saw

a)

Square stock

b)

Thick Stock

c)

Round Stock

d)

Flat Stock

7.
All table saw adjustments should be made:
a)
While the saw is in motion
b)
While the saw is completely stopped.
c)
It depends on which type of blade you're using.
d)
After the fence has been removed from the table.
8.
Do not use a ________ blade.
a)
dull
b)
sharp
c)
combination
d)
dado
9.
What is the purpose of the Miter Saw?
a)
To cut wood to length
b)
To rip wood
10.
What is another name for the Miter saw?
a)
Chop saw
b)
Table saw
11.

What is the minimum distance your fingers should be from the Saw Blade?

a)

4"

b)

2"

c)

12"

d)

6"

12.

The purpose of bringing the blade to the mark before making the actual cut with the motorized miter saw is to __________.

a)

see if the material is positioned correctly

b)

see if the saw is cutting properly and is set accurately

c)

see how the material will cut

d)

test the sharpness of the saw blade

13.
Make sure the blade is not touching the wood before the _________________ is turned on.
a)
Blade
b)
Switch
c)
Machine
14.
What PPE should be worn when operating the table saw
a)
gloves
b)
ear protectors
c)
safety glasses
d)
both b and c
15.

The Miter saw is used to cut material

a)

to length.

b)

to width.

c)

circular

d)

Diameter

16.

After cutting through your material

a)

Keep the blade moving while returning the blade to its start position

b)

Jump up and down in celebration

c)

Let the blade stop moving before returning to its start position

d)

Remove all clamps from the area

17.
What is the function of a jointer?
a)
to make a rip cut on a board
b)

produce a flat surface along a board's length and edge.

c)
to make a crosscut on a board
d)
All of the above
18.
What surface should you machine first on a board?
a)
Face
b)
Edge.
c)
End
d)
None of the above
19.
Identify the red part displayed in the photo??
a)
Guard for the belt sander
b)
Guard for the cutter head
c)
Guard for the miter saw
d)
Guard for the table saw
20.
Identify this part on this woodworking equipment.
a)
Infeed table
b)
Guard
c)
Fence
d)
Outfeed table
21.
You should avoid jointing an _______ on a board
a)
Face
b)
Edge
c)
End
d)
None of the above
22.
Stock to be planed of a jointer should be at least _____ inches long.
a)
12"
b)
9"
c)
16"
d)
18"
23.

Always allow the motor to reach _______________ before jointing.

a)

Half speed

b)

Full speed

c)

Partial speed

24.
Relief cuts are made with the band saw.  They _________.
a)
prevent the blade from binding
b)
are cuts made in a hurry
25.
Before removing your piece of wood and or wood waste; always wait for the _____to ______
a)
Teacher give the okay signal
b)
Switch to start
c)
Blade to stop
d)
None of the above
26.
Identify the part of the bandsaw numbered #9 depicted in the photo____________
a)
Blade
b)
Table
c)
Blade guides
d)
Off / On switch
27.

The band saw blade always cuts:

a)

Down

b)

Up

c)

Up & Down

d)

Sideways

28.
What must the operator due before operating the bandsaw?
a)
Make sure there is a blade in the machine
b)
Check to see if all of the guards are on
c)
Make sure the foot is 1/4" from the stock being cut
d)
All of the above
29.

Router cuts are made with a ________&__________ movement.

a)

rough & steady

b)

slow & steady

c)

rough and slow

d)

steady & fast

30.

which of these objects have been made on a wood lathe?

a)
b)
c)
d)
31.

To cut across the grain

a)

Crosscut

b)

Graincut

c)

Recut

d)

Backcut

32.
To flatten and smooth the face or edge of a board
a)
Laminate
b)
Joint
c)
Plane
d)
Route
33.
To cut with the grain
a)
Miter
b)
Bevel
c)
Rip
d)
Grain cut
34.
A lumber defect describing stock that is not flat
a)
Warp
b)
Worn
c)
Waste
d)
Bow
35.
Wood from a coniferous tree
a)
Hardwood
b)
Needlewood
c)
Softwood
d)
Pinewood
36.
Unit in which wood is measured and sold
a)
Linear feet
b)
Board foot
c)
Square foot
d)
Pallet lot
37.
The grade of particles in sandpaper
a)
Grade
b)
Grit
c)
Gauge
d)
3M
38.
A machine which reduces the thickness of boards.
a)
Jointer
b)
Saw
c)
Planer
d)
Sander
39.
Wood that will be removed in the finished work
a)
Firewood
b)
Sawdust
c)
Waste
d)
Waist
40.
A saw with a looped blade running around 2 wheels
a)
Loop saw
b)
Belt saw
c)
Wheel saw
d)
Band saw
41.

Deciduous trees most commonly create

a)

Rough wood

b)

Soft wood

c)

Hard wood

d)

Paper

42.
The widest side of the board
a)
Flank
b)
Face
c)
Edge
d)
Surface
43.
Piece of wood or plastic with fingers used to hold material against fence or table
a)
Featherboard
b)
Fingerboard
c)
Springboard
d)
Tailboard
44.
Number of teeth per inch
a)
TPI
b)
Pitch
c)
Rate
d)
Speed
45.
A form of paper with an abrasive surface
a)
Emery cloth
b)
Sand paper
c)
Stone paper
d)
Paper cloth
46.
When a workpiece is thrown back by a cutting device
a)
Withdrawn
b)
Kickback
c)
Backlash
d)
Whiplash
47.
The point at which two or more pieces of wood come together
a)
Edge
b)
Joint
c)
End
d)
Lid
48.
The side a machine in which the wood enters
a)
Infeed
b)
Down feed
c)
Entry
d)
Start
49.
A circular saw mounted to a stationary surface
a)
Table saw
b)
Radial arm saw
c)
Panel saw
d)
Miter saw
50.
The process of making a board dimensional
a)
Making
b)
Chipping
c)
Latheing
d)
Squaring
51.

Which of the following was NOT one of our projects this Trimester?

a)

Picture Frame

b)

Cutting Board

c)

Bird House

d)

Wood Mallet

52.

What angle was cut on the Picture Frame corners?

a)

90

b)

45

c)

180

d)

360

53.

What were the dimensions of the Cutting Board?

a)

10 x 14 x 1

b)

14 x 14 x 1

c)

12 x 20 x 2

d)

10 x 12 x 1

54.

What size was drilled into the Mallet head for the handle?

a)

.9"

b)

3"

c)

1"

d)

6"

55.

How wide were the Picture Frame sides?

a)

2 inch

b)

2 feet

c)

.75 "

d)

16 inch

Similar Resources on Wayground

Fall 2020 Final Exam Quizziz

55 questions

Fall 2020 Final Exam Quizziz

quiz

Worksheet

•

8th - 12th Grade

Softball

50 questions

Softball

quiz

Worksheet

•

KG - Professional Dev...

TSFA Certification Study Game

50 questions

TSFA Certification Study Game

quiz

Worksheet

•

9th Grade - Professio...

MARVEL MADNESS & POP CULTURE

59 questions

MARVEL MADNESS & POP CULTURE

quiz

Worksheet

•

5th - 12th Grade

Yu-gi-oh

52 questions

Yu-gi-oh

quiz

Worksheet

•

KG - Professional Dev...

Camera Basics

51 questions

Camera Basics

quiz

Worksheet

•

9th - 12th Grade

Spring 2018 ACP

50 questions

Spring 2018 ACP

quiz

Worksheet

•

9th - 12th Grade

AP Art History - China, Japan, Korea, Ancient Mediterranean

50 questions

AP Art History - China, Japan, Korea, Ancient Mediterranean

quiz

Worksheet

•

11th - 12th Grade