NEW
Font size
WorksheetsNAS Part 2 - Class B, C, and D
Total questions: 39
Worksheet time: 1hrs 18mins
ADS-B Out is required in which type of airspace?
HINT: This is also within the Mode C veil.
In Class E airspace below 10,000 MSL that is directly above Class D airspace.
In Class E airspace below a Class C shelf area.
Uncontrolled airspace within 30 miles of a Class B airport.
(Refer to Figure 20, area 1.)
What minimum radio equipment is required to land and take off at Norfolk International?
Mode C transponder and two-way radio.
Mode C transponder and omnireceiver.
Mode C transponder, omnireceiver, and DME.
The vertical limit of Class C airspace is generally
4,000 feet MSL.
4,000 feet AGL.
2,500 feet AGL.
What is the ten-mile wide ring that surrounds Class C airspace called?
The contact area.
The outer area.
The shelf area.
What is the radius of the Class C outer area?
20 NM.
10 NM.
30 NM.
Unless otherwise authorized, two-way radio communications with Air Traffic Control are required for landings or takeoffs
at all tower controlled airports only when weather conditions are less than VFR.
at all tower controlled airports within Class D airspace only when weather conditions are less than VFR.
at all tower controlled airports regardless of weather conditions.
(Refer to Fig. 70, area 3.)
How high does the Class D extend at Hayward Executive (HWD) airport?
Up to, but not including, 1,500 feet AGL.
Up to, but not including, 1,500 feet MSL.
1,500 feet MSL.
The vertical limit of Class C airspace above the primary airport is normally
4,000 feet AGL.
3,000 feet AGL.
1,200 feet AGL.
(Refer to Fig. 25, Area 3)
At what altitude does the Class B start over the Dallas Executive Airport (RBD)?
2,999 feet MSL.
3,001 feet MSL.
3,000 feet MSL.
(Refer to Fig. 25, Area 3.)
At what altitude does the Class B start over the Arlington (GKY) airport?
2,000 feet AGL.
2,000 feet MSL.
3,000 feet MSL.
What minimum radio equipment is required for VFR operation within Class B airspace?
Two-way radio communications equipment and a 4096-code transponder.
Two-way radio communications equipment, a 4096-code transponder, an encoding altimeter, and a VOR or TACAN receiver.
Two-way radio communications equipment, a 4096-code transponder, and an encoding altimeter.
(Refer to Fig. 70, Area 3.)
Within the Oakland Class C airspace, the airspace limits show a "T". What does this mean?
The top of the Class C stops where the bottom of the Class B begins.
The airspace is designated as a Terminal Radar Service Area.
The overlying Class B airspace includes a temporary shared volume.
Two-way radio communications must be established with ATC prior to entering which class of airspace?
Class G
Class E
Class C
(Refer to Fig. 74, area 1.)
You are planning to overfly the airport at Livermore (LVK) to the south. At what minimum altitude must you fly to remain clear of the surrounding Class D airspace?
2,900 feet MSL.
7,999 feet MSL.
2,901 feet MSL.
(Refer to Fig. 25, Area 3)
How high is the Class D airspace at Dallas Executive Airport (RBD)?
Up to, but not including, 3,000 feet MSL.
Up to, but not including, 3,100 feet MSL.
3,000 feet MSL.
Which initial action should a pilot take prior to entering Class C airspace?
Contact the FSS for traffic advisories.
Contact the tower and request permission to enter.
Contact approach control on the appropriate frequency.
(Refer to Fig. 25, Area 4)
What airspace exists at the surface at Ft. Worth Alliance (AFW)?
Class D
Class G
Class B
(Refer to Fig. 25, Area 3)
What is the floor of the Class B airspace directly over Dallas Executive Airport (RBD)?
3,000 feet MSL.
2,999 feet MSL.
3,001 feet MSL.
The Cabaniss NOFL (NGW) airport exists southeast of Corpus Christi International (CRP). What is the base of the Class C airspace over NGW?
2,500 feet MSL.
1,200 feet MSL.
Up to, but not including, 1,200 feet MSL.
(Refer to Figure 25, area 2.)
The floor of Class B airspace at Addison Airport is
2,500 feet MSL.
3,000 feet MSL.
at the surface.
You are operating from a satellite airport within Class C airspace. What must you do?
You must contact the Class C ATC controller as soon as practicable after takeoff.
You must monitor the Class C ATC controller until you are clear of Class C airspace.
You must file a flight plan prior to departure.
Which is true concerning the blue and magenta colors used to depict airports on Sectional Aeronautical Charts?
Airports with control towers underlying Class C, D, and E airspace are shown in magenta.
Airports with control towers underlying Class B, C, D, and E airspace are shown in blue.
Airports with control towers underlying Class A, B, and C airspace are shown in blue; Class D and E airspaces are magenta.
Airspace notated on the sectional chart within dashed blue lines is
Class C.
Class D.
Class B.
The normal radius of the outer area of class C airspace is
15 nautical miles.
20 nautical miles.
5 nautical miles.
The standard vertical limit of Class D airspace is
2,500 feet AGL.
4,000 feet MSL.
2,500 feet MSL.
Two-way radio communications are required at all towered airports
regardless of weather conditions.
unless weather conditions are below VFR minimums.
that have an automated weather reporting service.
(Refer to Fig. 74, area 4.)
At what altitude is the bottom of the Class B airspace at area 4?
2,900 feet MSL.
8,000 feet MSL.
6,000 feet MSL.
(Refer to Figure 23, area 3.)
What is the floor of the Savannah Class C airspace at the shelf area (outer circle)?
4,100 feet MSL.
700 feet AGL.
1,300 feet MSL.
The vertical limit of Class B airspace is generally
12,500 MSL.
10,000 feet AGL.
10,000 feet MSL.
What minimum radio equipment is required for operation within Class C airspace?
Two-way radio, and an altitude-encoding transponder.
Two-way radio, and a 4096 encoding altimeter.
Two-way radio, and a Mode C (or S) altimeter.
What is the first action you should take before entering Class C airspace?
You should contact the Class C approach controller via 2-way radio.
You should contact the Class C tower controller via 2-way radio.
You should contact FSS for traffic advisories.
What must you do after departing the Cuddihy private airport, south of Corpus Christi International?
Stay below 1,200 feet MSL until clear of the Class C airspace.
Squawk 7600 until clear of the Class C airspace.
Contact the Class C controller as soon as practicable.
What is required for entry into Class Bravo airspace?
Communications with the controller must be established.
You must hear the controller say your tail number.
An explicit clearance from ATC.
All operations within Class C airspace must be
in an aircraft equipped with a transponder with automatic altitude reporting capability.
in communications with the responsible ATC facility.
on a flight plan filed prior to arrival or departure.
The lateral dimensions of Class D airspace are generally
the instrument procedures that have been established for the airspace.
4 nautical miles from the center of the airport.
based upon the number of airports residing inside of the Class D surface area.
Airspace notated on the sectional chart within solid magenta lines is
Class G from the surface to 700 feet, then Class E.
Class B.
Class C.
If the control tower at a Class D airport ceases operation for the day, what happens to the airspace designation?
The airspace reverts to either Class E or Class G airspace.
The airspace designation remains the same.
The airspace reverts to the next lower Class.
Under what condition may an aircraft operate from a satellite airport within Class C airspace?
The pilot must file a flight plan prior to departure.
The pilot must contact ATC as soon as practicable after takeoff.
The pilot must monitor ATC until clear of the Class C airspace.
What minimum radio equipment is required for operation within Class C airspace?
Two-way radio communications equipment and a 4096-code transponder.
Two-way radio communications equipment, a 4096-code transponder, and an encoding altimeter.
Two-way radio communications equipment, a 4096-code transponder, and DME.
