It is a mortar consisting of cement, sand and water.

A fine-textured finish obtained by smoothing a fresh concrete, plaster or stucco surface with a wood float.

The surface of the concrete is grinded a day or two after it has set using a brick of carborundum, soft natural stone or emery. A sand-float finish is a method usig fine sand instead of grout.

A type of finish obtained by scrubbing or brushing the concrete surface while still green with fiber or wire brushes and water to remove the surface film or mortar leaving the coarse aggregate exposed.

Concrete surfaces may be finished by tooling by any of the methods employed for dressing or finishing natural stone.

A coarse-textured finish obtained by fracturing a concrete or stone surface with a power driven hammer having a rectangular head with a corrugated, serrated or toothed face.

The same appearance as that of a brushed finish. It produces a granulated finish similar to sandstone but is not so uniform because the aggregates are likely to be brought out irregularly.

A decorative finish produced by sandblasting, etching with an acid, or scrubbing a concrete surface after the initial set in order to remove the outer layer of cement paste and expose the aggregate.

Coloring agents are added to mixture; it may be troweled, sandblasted, tooled, stamped etc.

Form materials (Boards, or panels such as plywood) may be used to impart a surface texture to concrete.

Plastic-thermoplastic or synthetic rubber sheets formed in a variety of patterns and/or textures are attached to the inside faces of formwork.

What is NOT considered a coat for cement plastering?

A coats that mixed in the proportion of 1 part portland cement to 3 parts of sand with about 10lbs of hydrated lime.

a coats that mixed in the proportion of 1 part portland cement to 2 parts of sand.

coarse sand is used for the ________________ and fine sand for the finish coat

average thickness of scratch coat and brown coat

thickness of the finish coat is _____ minimum and rarely exceeds 1/4" except for finishes requiring rough texture.

in integral colored cement finish, the finish coat of________is applied

The concrete aggregate is forced below the surface, and the surface is then leveled with a straight wood screed and while the concrete is not firmly set, it is given a float finish with a straight, flat wood trowel called floats.

Smooth crushed stone, most commonly marble aggregate in concrete toppings over concrete base slab.

After the concrete aggregate is force below the surface, the surface is then leveled with a straight wood screed, and given a wood float finish. The entire surface is then steel-troweled before the concrete finally sets.

When the concrete is still green but the surface water is gone, the surface is leveled with a straight wood screed. Finish coat is leveled with a wood screed, given a float finish and then steel-troweled.

These separate finishes are designated as non-slip, heavy duty, colored cement, etc.

Moderately rough finish for horizontal surfaces where slip resistance is required and appearance is a consideration.

Light to Heavy rough finish for horizontal finishes where slip resistance and appearance is a consideration.

Medium-to-Heavy texture for large surfaces, such as roadway pavements where slip resistance is required and appearance is of secondary importance.

Finish Coat of pigmented white cement is applied by throwing it vigorously over screeded and broomed for better bonding

Similar in appearance to travertine, produced by scattering rock salt over a trowelled surface and then dissolving the salt after the concrete has hardened.

Concrete cast over a bed of crushed stone or gravel aggregate against a polyethylene sheet between them to prevent bonding.

Proprietary aluminum tools are used to imprint various patterns in freshly placed horizontal concrete surfaces

This consists of a topping with a mixture of 1 part cement, 1 part sand and 1 part finely crushed stones.

A mosaic floor or paving composed of marble or other stone chips set in a cementitious or resinous matrix and ground when dry.

A ground and polished terrazzo finish consisting mainly of relatively small stone chips.

A ground and polished terrazzo finish consisting mainly of large stone chips, with smaller chips filling the spaces between.

A uniformly textured terrazzo finish produced by washing the matrix prior to setting so as to expose the chips which are not ground.

A mosaic terrazzo finish consisting of cut or fractured marble slabs set by hand in the desired pattern, with smaller chips filling the spaces between.

What type of Terrazzo Finish is this?

What type of Terrazzo Finish is this?

What type of Terrazzo Finish is this?

What type of Terrazzo Finish is this?

Finely ground corundum may also be a part of the aggregate to produce an enduring and non-slip surface.

A terrazzo Topping installed directly over a rough finished concrete slab. A chemical bonding agent is used if the concrete surface is too smooth for a mechanical bond.

quick-setting gypsum plaster consisting of a fine white powder (calcium sulfate hemihydrate), which hardens when moistened and allowed to dry.

Concrete or masonry surface should be ___ to ensure good bonding before applying the stucco or plaster cement.