WorksheetsVehicle 1 inspection 5 New 5
Total questions: 23
Worksheet time: 12mins
What safety precaution should a technician make prior to inspecting a hybrid/electric vehicle?
Ensure the 12v system is isolated
Ensure the high voltage system is isolated
Ensure the 12v and high voltage systems are isolated
Ensure the high voltage battery is charged whilst disconnected.
To comply with work-based policies, what should a technician do before carrying out a vehicle inspection
Valet the interior
Measure tyre tread depths
Fit suitable protection
Check the odometer is accurate
During an inspection, a tyre has a cut on the side wall exposing the ply cords, what recommendations would be given to the customer?
Replace the tyre
Repair with tyre weld
Repair with plug patch
Swap with rear wheel
Which of the following should be carried out when a damaged lower suspension arm is replaced, to ensure the vehicle conforms to operating specifications.
A roller brake test
A full (DVSA) MoT
A dynamometer
A full steering alignment check
What would a technician use to identify a fault when a malfunction indicator lamp (MIL) is illuminated?
A fault code reader
A fuel pressure guage
A coolant pressure guage
A lest light to the instrument panel
During a regular inspection, what would the procedure if a damaged constant velocity gaiter /boot is identified?
Replace and rebalance
Re-grease and seal with glue
Refit new ball bearings and gaiter
Clean, regrease and fit new gaiter
What are the implications if a technician fails to recognise a wheel imbalance during a road test as part of a vehicle inspection?
Premature suspension wear
Power steering fluid aeriation
Steering geometry misalignment
ABS system will activate when driving normally
What affect would WEAK antifreeze have on the operation of a coolingf system
Reduced Frost protection and over cooling
Reduced frost protection and corrosion inhibitors
Reduced frost protection and auxiliary belt damage
Reduced frost protection and air conditioning pump seizure
When carrying out a four-wheel alignment, how should the steering wheel be locked?
With the steering wheel on full right hand lock
With the ignition key in the on position
In the straight-ahead position with a clamp tool
In the straight-ahead position with the hand brake applied.
If a vehicle had a parking brake efficiency of 10% what would be recommended to the customer?
Replace all shoes
Advise the brakes are OK
Strip the brakes for further examination
Replace brake shoes, drums and cables.
If a vehicle is presented for service with scratches on the rear bumper, what would be the FIRST action required of the technician?
Polish the scratches to see if they can be removed
Record the damage and report it before starting work
Start the service and do not record pre-service damage
Record the damage and report it once all work completed
During a maintenance check, excessive blue smoke is emitted from the exhaust, where would the test results be recorded
Workshop manual
MOT failure sheet
Daily workshop load chart
Vehicle service checklist
What affect would an excessively worn ball joint have on the front suspension system?
Produce incorrect thrust angle
Produce incorrect camber angle
Produce failure of torsion bar bushes
Produce poor suspension damper operation
What id the legislation that sets guidelines for the collection and processing of personal information from individuals?
Global Data Protection Rule
General Data Protection Rule
Global Data Protection Regulation
General Data Protection Regulation
During a regular inspection what would be checked on a manual gearbox?
Oil level
Pre-load
Backlash
Re-mapping
Which type of inspection provides information to the customer on the condition of their vehicle to pass the annual DVSA test?
Pre-MOT inspection
Post work inspection
Pre delivery inspection
Safety recall inspection
What important information does the VIN plate provide
Component location information
Breakdown recovery information
Service interval information
Vehicle manufacturing information
What should a technician do FIRST when testing a vehicle steering geometry to comply with work-based policies?
Adjust the steering arms
Check the tyre pressures
Identify the vehicle weight
Remove both front wheels
Under what engine operating conditions should an emissions test for a vehicle with a compression ignition engine be carried out?
At just above idle speed only
At normal working temperature
At a fixed speed of 5000 revs/min
At both hot and cold temperatures
During an inspection a technician identifies the rear brake pads are worn to 2.5mm, what recommendations would be made to the customer?
Replace the brake pads immediately
Do not operate the electronic handbrake
Strip clean and adjust brake pads immediately
Replace the brake pads during the next annual service
I drive a BMW and the light comes on at 4mm
Which one of the following tests would be used to check tolerances during a DVSA test?
Roller brake tester
Wheel alignment gauge
Antifreeze Refractometer
Engine compression tester
Which of the following implications would occur if a technician completed a service on a climate control system incorrectly?
Engine overheating
Damage to the condenser
Bacterial, Mould and fungi growth
Seized air conditioning compressor
What is the main reason for completing accurate recorders during a vehicle inspection?
Ensures the vehicle meets DVSA stanards
Ensures only MOT specific items are checked
Ensures all the inspection checks are carried out
Ensures the work is completed within the allocated time
