10.When installing flexible insulation between studs, staple the side flanges at intervals of _____ inches.

To be effective, the metal foil surface of reflective insulation must face an open - air space with a depth of at least _____. Inches.

9.When exposed to fire, some urethane foam insulation can emit _____.

In cold weather, reflective insulation is highly effective in preventing heat loss.

The least expensive type of rigid or semirigid insulation is _____.

Settling over time is a disadvantage of _____ insulation.

Flexible batt insulation (fiberglass or mineral wool) is manufactured in widths of 15" or _____inches.

The space between panes of double-pane or triple-pane windows may be filled with the inert gas _____.

Where does wood come from?

Miscellaneous types of insulation include light weight aggregates, foamed-in-place insulation, and ______________.

Reflective insulation with the foil side must face an open-air space of at least _____inches.

 Which type of insulation is available in sheet or board form, available as structural or nonstructural boards, nonstructural board applied to exterior/interior of foundations, under perimeter of concrete slabs, over wall sheathing, and on top of roof decks

What type of insulation is available in bags or bales, blown or poured over ceiling joists or blown into walls.

Flexible insulation batts come in two widths, which are___________

First aid procedures must be listed on the SDS for each product manufactured.

Personal protective equipment (PPE) such as gloves, eye protection, and respiratory protection s only optional when installing insulation.

SDS is the abbreviation for ________

The board nailed to the rafter tails in order

to space the rafters is the _______ .

A(n) _______ is used when lifting large

members with a crane.

The _______ extends beyond the gable and

supports a decorative end piece.

An overhang is framed using short lengths

of boards known as a(n) _______ .

A(n) _______ should be attached to a truss

that is being set by a crane.

The framework extending from the roof

surface that provides additional light and

ventilation is referred to as a(n) _______

A truss is fastened to a top plate by

toenailing through the _______

The upper ends of rafters are fastened to

the ________ .

A(n) _______ is an L-shaped arrangement

of lumber that is fastened to the tops

of long ceiling joists to keep them in

alignment.

A roof with four sides extending toward

the center is a(n) _______ .

The amount of rise per 12" of run is

referred to as the _______

When framing members are assembled

one piece at a time, it is referred to as

_______ .

A(n) _______ is a 1 × 4 member that is

nailed to the ceiling joists to prevent

twisting and bowing of the joists.

Commercial roofs are may be supported

by _______ , which are welded to the

structural steel.

A(n) _______ is a roof support member

that runs parallel to the plate and is

installed between the plate and the

ridgeboard.

The company's address and phone number will not be found on the SDS.

Doors are generally classified as either solid or hollow core.

The bottom of a wood jamb must be flush with the floor.

The required height of a hinge is determined by the​ ________ of the door.

A(n) _______ is a roof support member

that runs parallel to the plate and is

installed between the plate and the

ridgeboard.

The space between panes of double-pane or triple-pane windows may be filled with the inert gas _____.

What type of insulation is available in bags or bales, blown or poured over ceiling joists or blown into walls.

The board nailed to the rafter tails in order

to space the rafters is the _______ .

An anchor point used for tying off a safety harness should be​ _____.

The shingles in common use today are​ _____.

The underlayment commonly used in pitched roof installations is​ _____.

All tile roofing material is made of clay.

A rule of thumb for attic ventilation is 1 square foot of ventilation for every​ ____ square feet of attic area.

The rake edge drip edge flashing is applied before the underlayment.

Valley flashing should be nailed every​ ______ inches.

The purpose of a cricket is to​ _____.

A _______ roof has two slopes that meet at

the center to form a point.