A switch intended for use in general distribution and branch circuits. It is rated in amperes, and it is capable of interrupting its rated current at its rated voltage, is a __ switch.

The permanent joining of metallic parts to form an electrically conductive path that will ensure electrical continuity and the capacity to conduct safely any current likely to be imposed is known as ___.

A circuit breaker that has purposely introduced into a delay in the tripping action and which delay decreases as the magnitude of the current increases is a __ circuit breaker.

A switch intended for isolating an electric circuit from the source of power that thas no interrupting rating, and it is intended to be operated only after the circuit has been opened by some other means is a/an ___.

Not readily accessible to persons unless special means for access are used is ___

The definition of ampacity is

The definition of ambient temperature is

Type of service where both the load and the time intervals may have wide variations.

Special permission is ___.

An overcurrent protective device with a circuit opening fusible part that is heated and severed by passage of overcurrent through it is called ___.

The service conductors between the terminals of the service equipment and a point usually outside the building, clear of building walls, where joined by tap or splice to the service drop is called ___

A dwelling unit is ___.

Where the conductor material is not specified in the Code, the conductors are assumed to be ___.

Mandatory rules of the Code are identified by the use of the word ___.

Advisory rules of the Code are identified by the use of the word ___

. Continuous duty is ___.

An enclosure designed either for surface or flush mounting and provided with a frame, mat or trim in which a swinging door or doors are or may be hung is ___

All wiring must be installed so that when completed ___.

So constructed or protected that exposure to the weather will not interfere with successful operation defined the __

. The current-carrying capacity of conductors expressed in amperes is ___.

Service raceways shall be equipped with a ___ service head at the point of connection to service drop conductors.

A circuit breaker with a trip setting of not more than __ times the ampacity of conductor shall be considered as to provide the required short circuit protection.

Service conductors in cable shall NOT be smaller than ____

. Using aluminum or copper clad aluminum conductors, the minimum size of service entrance conductors shall be ____.

The lighting load for a dwelling unit expressed in terms of volt-ampere per sq. meter must be at least _______.

In dwelling units, at least one wall receptacle outlet shall be installed within _________mm of the outside edge basin or bath tub.

Power circuit breaker can be classified according to operation, some of these are, except

Outlets for specific appliances such as laundry equipment, shall be within ___ of the appliance.

An insulated grounded conductor of 14mm2 or smaller shall be identified by a continuous _______ outer finish along its entire length.

The following are the standard ampere rating of a breaker which one is NOT?

A fuse or an overcurrent trip unit of a circuit breaker shall be connected in ________ with each ungrounded conductor.

. Enclosures for overcurrent devices shall be mounted in a ___ position unless in individual instances this is shown to be impracticable and is installed in accordance with 2.40.33 (PEC 2.40.33)

An overcurrent trip unit of a circuit breaker shall be connected in series with each___. (PEC 2.40.2.1)

Fuses and circuit breakers shall be located or ________ so that the persons will not be burned or otherwise injured by their operation. ( PEC 2.40.4.2 (a) )

The neutral conductor shall not be _______. ( PEC 2.40.2.3)

What is the minimum size of grounding electrode copper conductor (PEC 2.50.3.17 )

The conductor with the highest insulation temperature rating is________. (PEC Table 3.10.1.13)

Concrete, brick or tile walls are considered as being. (PEC 3.0.1.6 b)

Is it permissible to install direct current and alternating current conductors in the same outlet box. (PEC 3.0.1.3 c1)

The neutral conductor _______. (PEC 3.10.1.15 b4 )

Installing more than three current carrying conductors in the same conduit requires _______. ( PEC 3.10.15.b 2 a )

The Code rule for maximum 90- degree bends in a conduit between two boxes is four, the most likely reason for the total 360-degree limitation is (PEC 3.50.2.7)

The total load on any overcurrent device located in a panelboard shall not exceed _____ of its rating where in normal operation the load will continue for 3 hours or more ( PEC 3.84.3.4(d) )

Two metals of different materials shall not be joined together in order to avoid the _______ action (PEC 3.46.1.3)