wayground logo

Free Printable Worksheets

Font size

S
M
L
XL
Worksheets

Ag Structures Mid-term #2 2026

Total questions: 100

Worksheet time: 1hrs 6mins

Name
Class
Date
1.
a)

sawbench

b)

planer thicknesser

c)

planer

d)

jointer

2.
a)

bandsaw

b)

drillpress

c)

drill

d)

saw

3.
a)

drillpress

b)

bandsaw

c)

cordless drill

d)

drill

4.
a)

cordless drill

b)

bandsaw

c)

drillpress

d)

workbench

5.

What saw is used to cut out irregular shapes?

a)

Table Saw

b)

Band Saw

c)

Chop saw

d)

All of the above

6.

How far above your material should a table saw blade be positioned?

a)

Between 1 -2"

b)

2"

c)

More than an 1"

d)

About a 1/4"

7.

You must use a fence with our router table when:

a)

The router bit has a bearing attached to it

b)

Using a 1/2" Collet

c)

The router bit does not have a bearing attached to it

d)

The router bit is made of carbide steel

8.

When using the drill press, it is necessary to:

a)

Tighten bits in the chuck with your hands only

b)

Turn on the machine with the chuck key inserted into the chuck

c)

tighten bits with the chuck key before operation

d)

All of the above

9.

The following tool is a called a:

a)

Band Saw

b)

Scroll Saw

c)

Table Saw

d)

Circular Saw

10.

The following tool is called a:

a)

Band Saw

b)

Power Miter Box Saw

c)

Scroll Saw

d)

Jig Saw

11.

What is the best use for this tool?

a)

Marking lines on an angle

b)

Marking lines square to an edge

c)

Marking straight lines

d)

Marking diagonal lines

12.
In terms of sandpaper; 40 grit is very__________
a)
Rough
b)
Fine
c)
Wet
d)
Smooth
13.

Which determines if a bit can be used in a particular drill?

a)

length

b)

shank size

c)

weight

d)

material type

14.

Which saw makes the most accurate crosscuts and angled cuts?

a)

band saw

b)

miter saw

c)

reciprocating saw

d)

coping saw

15.

Thin blades are best for:

a)

Cutting straight lines

b)

Shaping edges

c)

Cutting irregular shapes & curves

d)

cutting angles

16.

What piece of PPE (personal protective equipment) should you ALWAYS wear when you're in the shop?

a)

Earplugs

b)

Safety Glasses

c)

Gloves

d)

Work Apron

17.

Name the tool shown.

a)

Tri-square

b)

Set-square

c)

Mortise Gauge

d)

Jack Plane

18.

Name the tool shown.

a)

Flat head screwdriver

b)

Phillips head screw driver

c)

Bradawl / Bradle

d)

Nail punch

19.

Name this joint

a)

Butt

b)

Dado

c)

Biscuit

d)

Miter

20.

What joint is shown in the image?

a)

Cross halving

b)

Comb/Finger

c)

Bridle

d)

Dovetail

21.

What is the name given to the joint in the image?

a)

Dado

b)

Mitre

c)

Tongue and groove

d)

Scarf

22.

When operating the Miter saw, ensure:

a)

There is no space between the board and the fence

b)

You always ensure at least one square edge and square face

c)

You let the blade do the work (don't try to cut too fast).

d)

All of the above

23.

Which direction does the teeth point on the band saw?

a)

up

b)

down

c)

up and down

d)

sideways

24.

When using the Miter saw what is your left hand responsible for?

a)

Bringing down the saw to make your Cut

b)

Pressing down the trigger to run the saw

c)

Holding the wood up against the fence

d)

Waving at your classmates

25.

The blade on the band saw is described as?

a)

One continuous loop

b)

Hack saw

c)

Round circle like the table saw

d)

Reciprocating blade

26.

What holds the bit on the drill press?

a)

Chuck

b)

Snapper

c)

clamp

d)

grabber

27.

What device do we use to change the drill bit on the drill press?

a)

Chuck Key

b)

Raptor Key

c)

Trapper Key

d)

Grabber key

28.

What hand tool is this?

a)

Ball Peen

b)

Mallet

c)

Claw Hammer

d)

sledge

29.

What is the name of this type of screw driver?

a)

Phillips head

b)

flat head

c)

hex head

d)

D head

30.

What is the name of this shop tool?

a)

Belt sander

b)

disk sander

c)

drum stander

d)

spindle sander

31.

Which of these safety rules apply when you are working in the shop?

a)

Safety glasses always on

b)

Long hair pulled back

c)

Long sleeves rolled up

d)

All of the above

32.

How do I know what type of sand paper I am using?

a)

Feel it

b)

Look on the back

c)

Try it out

d)

Ask the teacher

33.

What type of cut do you make when you cut with the grain?

a)

Rip cut

b)

hammer cut

c)

cross cut

d)

zipper cut

34.

When using the band saw your hands should never be ____________________ the blade?

a)

behind the blade pulling the wood.

b)

directly in the blades path

c)

on each side of the blade guiding the wood through the cut

d)

away from the blade

35.

Name these two parts of a drill press?

a)

Drill chuck/Chuck key

b)

Drill shank/Chuck key

c)

Drill Key/Chuck shank

d)

Drill chuck/ Shank key

36.

Which part of the drill bit allows the waste to be removed during drilling?

a)

Flutes

b)

Shank

c)

Body

d)

Land

37.

The band saw upper blade guard should be between _____ to ____ above the stock (material) you are cutting.

a)

1/8" , 1/4"

b)

1/4", 1/2"

c)

1/2", 3/4"

d)

It doesn't matter as long as it clears the material.

38.

Which sander below is used to remove a lot of material from the face of a board in a short amount of time?

a)

pad

b)

disc

c)

palm

d)

belt

39.

Identify this measurement in simplest form.

a)

53"

b)

4' 4"

c)

4' 6"

d)

4' 5"

40.

If 1 foot is equal to 12 inches. How many inches are in 4 feet?

a)

12

b)

24

c)

36

d)

48

41.

Identify this measurement in simplest form.

a)

10"

b)

11"

c)

12"

d)

13"

42.

Convert 10'-8" to inches

a)

108"

b)

102"

c)

128"

d)

98"

43.

Convert 5'-7" to inches

a)

67"

b)

60"

c)

86"

d)

98"

44.

49 INCHES = ____________feet

a)

3 ' - 11"

b)

4' - 1"

c)

4' - 3"

d)

4' - 10"

45.
Measure this line using inches.
a)
5 in.
b)
5 ¼ in.
c)
5 ½ in.
d)
5 ¾ in.
46.
PPE stands for _________  ________ ________
a)
Professional Protective Equipment
b)
Proactive  Protective Equipment
c)
Personal Protective Equipment
d)
Personal Prevention Equipment
47.

You need 10 walnut boards for a home project. The dimensions of the wood needed is 1" x 12" x 1' for each piece. If the price for walnut is $2.50 per Bf, How much will this project cost for the wood only?

a)

$12.50

b)

$25.00

c)

$35.00

d)

$48.50

48.

What does squaring a board mean?

a)

All sides are parallel

b)

All sides are parallel and their corners are 90 degrees

c)

Making a cut on the compound miter saw

d)

Ripping a board on the table saw

49.

Which below are units of measure within the Metric System?

a)

Inches, Millimeters and Yards

b)

Millimeter's, Grams, and Kiloliters

c)

Feet, Yards and Miles

d)

Kilograms, Ounces, Pounds

50.

What does the subject of pneumatics study ?

a)

The study of converting wind energy into electrical energy

b)

The study of compressed gas energy converting to mechanical energy

c)

The study of liquid energy converting to mechanical energy.

d)

Non of the above

51.
What is being applied to wood  in the photo________?
a)
Stain
b)
Wax
c)
Sanding
d)
Wood Putty
52.
A ___________ is applied to wood over a stain in order to protect the wood.
a)
veneer
b)

finish/sealer

c)
tack cloth
d)
600 grit sand paper
53.

Name this joint

a)

Finger

b)

Dado

c)

Lap

d)

Miter

54.

Name this joint

a)

Rabbet

b)

Dado

c)

Lap

d)

Finger

55.

A board foot is equal to?

a)

1' x 1' x 1'

b)

12" x 12" x 1"

c)

12' x 12' x 12"

d)

144" x 1' x 1"

56.

What is the Purpose of the Department of Labor and OSHA?

a)

Create regulations for private industries to follow

b)

To make working conditions better for workers

c)

To test products created to see if they are safe

d)

To allow for a free market for all companies

57.

Name the following hand tool?

a)

Finish hammer

b)

framing hammer

c)

mallet

d)

ball peen hammer

58.

Which below is a English standard unit of measurement to measure how long a pencil is?

a)

Millimeter

b)

Centimeter

c)

Inches

d)

Feet

59.

Name the following tool?

a)

Wood brush

b)

Bench sweep

c)

Wire Brush

d)

Awl

60.

Name this joint

a)

Lap

b)

Finger

c)

Miter Butt

d)

Dovetail

61.

You need 4 boards for a bird house. The dimensions are 1" x 6" x 2' for each side. How many board feet will you need?

a)

2 Board feet

b)

4 Board foot

c)

8 Board feet

d)

14.5 Board Feet

62.

What is the name of this Defect?

a)

Bowing

b)

Cupping

c)

Twisting

d)

Indenting

63.

Name the following tool?

a)

Tri-square

b)

Combination Square

c)

Framing Square

d)

Speed Square

64.

Name the following tool?

a)

Wood Chisels

b)

Flat head screwdrivers

c)

Wood Files or Rasp

d)

Awl

65.
PPE stands for _________  ________ ________
a)
Professional Protective Equipment
b)
Proactive  Protective Equipment
c)
Personal Protective Equipment
d)
Personal Prevention Equipment
66.

Which below are units of measure within the Metric System?

a)

Inches, Millimeters and Yards

b)

Millimeter's, Grams, and Kiloliters

c)

Feet, Yards and Miles

d)

Kilograms, Ounces, Pounds

67.

Which sander below is used to remove a lot of material from the face of a board in a short amount of time?

a)

pad

b)

orbital

c)

palm

d)

belt

68.
In terms of sandpaper; the abrasive particles on the sandpaper is referred to as ___________
a)
Grit
b)
Kerf
c)
Verneer
d)
Wood Putty
69.

If you are building a project that requires 4 Bf. What is the difference in cost if you wanted to build it out of Oak which is $8.25 a BF compared to Pine that is $3.00 a Bf?

a)

$12.00

b)

$21.00

c)

$33.00

d)

$45.00

70.

What is the name of this Defect?

a)

Bowing

b)

Crook

c)

Twisting

d)

Indenting

71.

Which clothing item is not safe to wear while working on the drill press.

a)

short sleeve shirt

b)

sneakers

c)

hooded sweatshirt

d)

t-shirt

72.

What does the subject of pneumatics study ?

a)

The study of converting wind energy into electrical energy

b)

The study of compressed gas energy converting to mechanical energy

c)

The study of liquid energy converting to mechanical energy.

d)

Non of the above

73.

When using the drill press, it is necessary to:

a)

Tighten bits in the chuck with your hands only

b)

Turn on the machine with the chuck key inserted into the chuck

c)

tighten bits with the chuck key before operation

d)

All of the above

74.
A stain is designed to enhance the wood  ______ and change the _____ of wood.
a)
grain + structure
b)
grain + color
c)
glue + color
d)
grain + knots
75.

Between applying coats of finish/sealer one should _____ between coats

a)
Stain
b)
Scrape
c)
Wax
d)
Sand
76.
When sanding wood one should sand _______   ______ wood grain
a)
across all
b)
against all
c)
with the
d)
with circles
77.

Name one type of hard wood?

a)

Pine

b)

Oak

c)

Balsa

d)

Cedar

78.

What is the name of this Defect?

a)

Bowing

b)

Crook

c)

Twisting

d)

Indenting

79.

What is the name of this Defect?

a)

Bowing

b)

Crook

c)

Splitting

d)

Indenting

80.

What is the name of this Defect?

a)

Bowing

b)

Crook

c)

Cracking

d)

Knot

81.

Name the tool shown.

a)

straightener

b)

Set-square

c)

Level

d)

Jack Plane

82.

Name the tool shown.

a)

straightener

b)

Pry Bar

c)

Level

d)

nail remover

83.

A Wood Planer changes what part of the board?

a)

Length

b)

Thickness

c)

Width

d)

Height

84.

Name the tool shown.

a)

Utility Knife

b)

Scraper

c)

Bench Dog

d)

Pliers

85.

Which career below requires a college degree?

a)

Electrician

b)

Plumber

c)

Engineer

d)

Heavy Equipment Operator

86.

True or False. Wood glue is stronger than wood if used properly?

a)

True

b)

False

87.

What is 32 dg in grams?

a)

0.32 g

b)

3.2 g

c)

32 g

d)

320 g

88.

Select the largest unit.

a)

kilogram

b)

centigram

c)

decigram

d)

decagram

89.
Convert from meters to cm:  9 meters
a)
900 cm
b)
90 cm
c)
0.9 cm
d)
0.09 cm
90.
Convert 8 kilometers to meters
a)
800 m
b)
80,000 m
c)
8,000 m
d)
.008 m
91.
490,000 g =____ kg
a)
490
b)
49
c)
4,900
d)
0.49
92.

The basic metric unit for mass is the ...

a)

gram (g)

b)

meter (m)

c)

liter (L)

d)

Celcius (°C)

93.
The basic metric unit for volume is the .....
a)
gram (g)
b)
meter (m)
c)
liter (L)
d)
Celcius (°C) 
94.
The prefix milli represents the value ....
a)
10
b)
100
c)
1,000
d)
0.001
95.

Another name for a scroll saw?

a)

Small Blade cutter

b)

Reciprocating saw

c)

Circular blade saw

d)

Up and down cutter

96.

Name one type of soft wood?

a)

Pine

b)

oak

c)

Maple

d)

Walnut

97.
When inserting the wood into the planer, the wood is cut on the _______
a)
left side
b)
Bottom
c)
rough side
d)
top side
98.

What is the function of a jointer?

a)

to make a rip cut on a board

b)

a woodworking machine used to produce a flat surface along a board's edge.

c)

to make a crosscut on a board

d)

All of the above

99.

Which sander below is used for sanding inside curves?

a)

Palm Sander

b)

Belt Sander

c)

Drum Sander

d)

Orbital Sander

100.

Thin blades are best for:

a)

Cutting straight lines

b)

Shaping edges

c)

Cutting irregular shapes & curves

d)

Small cuts