Which of the following structural type relies on sectional properties of rigid components?

weather-resistant material (eg. asphalt-saturated roofing felt used to cover or protect roof sheathing or decking before shingles or tiles are applied

Placement of fasteners should be placed at the _______ or _______ and not at ________ or ________.

Which of the following structural type naturally direct loads through its shapes?

Corrugated side lapping:

What type of gutter fastener is this

CLASS AA Ratio by Volume. Cement : Sand : Gravel

Rebars have ____ or ____ to increase surface area and ensure proper adhesion with concrete

True or False: Downspout bend should be in 90degree angle from the gutter to the wall(attached)

This type of support is able to bridge larger unsupported spans. It is lightweight and only experience axial tension or axial deformation.

Structural dependent on its (web) interlinked slender rigid components

Technical term that simply refers to forces acting on buildings or its structural elements is called

Composed of series of structural support that is not structurally responsive against winds. This is mainly used in houses of countries that experiences extreme cold weather.

Identify the Timber Roof Truss Component No.1

Identify Timber Roof Component No. 6

Rigid structures capable of resisting Axial (Compression and Tension) and Shear Stress because it has a surface?

_______ ______ are an important component of any roofing system. They are installed along the peak of the roof, and they allow warm air to escape from the attic during the summer time and moisture to escape in the winter time.

Any physical influence that is capable of Changing the State of Rest or Motion or geometry of an object.

Nicknamed 'the Coathanger' because of its arched design, the 1,149m-long, 48.8m-wide structure is the world's tallest steel arch bridge

To check for Equilibrium of Forces, all should equal to ____

_______ is a wavy dormer that protrudes through the slope of a roof. It contains a window that may be fixed or operable.

Type of stress that tends to lengthen an object or a material

In architecture, a vertical window that projects from a sloping roof and usually illuminates a bedroom is called ______. These are set either on the face of the wall or high upon the roof, and their roofs may be gabled, hipped, flat, or with one slope.

Type of 2Dimensional plates for connecting heavy timber. It is commonly used with MC bolt a with a label of ASTM 36 Steel.

Truss welded unto _______ that is tied to RC roof beam using anchor bolts. This is placed under one end of a truss beam, girder, or column to distribute the load

Light gauge metal plates used to connect pre-fab light frame wood truss members

Board or structural panels fastened to the wall or roof Framing as base for cladding or roofing materials

Corrugated End Lapping:

A ______ ______ has perforations that allow air to travel in and out of an attic. Installing _______ _______ prevents costly damage to your roof, gutters and attic by providing airflow and mitigating trapped heat on the interior. This allow air movement and give the hot, humid air an exit point out of your roof.

Known Architectural Sheet Metal manufactures in the Philippines are all listed below except for:

a minimum _____ pitch/slope is required for lower pitch type of roof

The typical specified gauge number for Galvanized steel roof used in the Philippines for residential and commercial projects is

______ is specified for Flashing, Gutter, Ridge Caps and Gutter Caps. What gauge number is it for Galvanized Steel?

Identify no.1

Identify No.2

Identify type of Flashing:

Identify this type of roofing fastener

Identify this type of fastener for the roof

Hook bolt with square bent is usually put in what type of roofing

Which one is the Gutter bracket?

Stress that tends to shorten an object or material

Identify Gutter Accessory

_________________ is made from polyethylene foam. An excellent material used as thermal insulation: roofs insulation, wall insulation, floor insulation. It is an Aluminum Film in one or both sides. It can be attached to roof framing structures(eg. purlins)

______________ an insulation material that slows the spread of heat, cold, and sound. It is much more commonly used, partially because of its affordability. It has a good R-value, even if it’s not the best. Though it’s a non-combustible material, it doesn’t provide the level of fire block that other wool insulation does.