All of these are drivetrain components EXCEPT?

All front-engine front-wheel drive vehicles use a traverse -mounted engine coupled to a transaxle

In a transverse front-wheel drive layout application, the transaxle is normally mounted at the ___________ of the engine and a primary shaft engages with the splines of the clutch center plate.

Vehicles with independent rear suspension have:

In vehicles with an independent rear suspension, the final drive unit is mounted on the chassis frame, and drive is transferred to each road wheel through external driveshafts (half-shafts), which have flexible joints on each end.

Choose the correct statement:

Select one:

With a(n) _____, drive from the engine is transmitted to a rear axle assembly by a drive (propeller) shaft.

In some rear-wheel drive (RWD) vehicles, the rear U-joint connects directly to a(n)

U-joints are typically used on driveshafts because they generally need to accommodate only small angles, although some manufacturers use CV joints to provide a smoother ride, or on off-road vehicles that have been lifted and experience a greater amount of suspension travel.

On a semi-floating axle vehicle, the axle flange is bolted to the housing, while the vehicle's weight is supported by the hub & bearing.

The ___________ does not provide any drive capabilities and is used on the rear of front-wheel drive vehicles.

Which of the following axles uses a single roller bearing between the hub and the outside of the axle housing?

_______ use combinations of driveshafts and half-shafts depending on if the axle shafts are independent or nonindependent.

In the ________ axle, the axle bearing is placed between the axle and the axle housing.

Select one:

It is always good practice to check runout on the drive axle flange when there is a customer concern of vehicle vibration.

Provision is normally made for adjusting the alignment of a two-piece driveshaft assembly by using _______ under the carrier bearing.

Select one:

In all rear-wheel drive and four-wheel drive vehicles, engineers fit a CV joint to the front end of the driveshaft, which allows for an increase of angles of the shafts without creating vibration.

While both can transfer torque through an angle, the U-joint can do so at a much greater angle than the CV joint, which is why it is used on front half-shafts to accommodate large steering angles.

Worn axle bearings allow the axle shafts to move, and the axle shaft movement will wear the axle seals quickly and create ____ that the axle fluid can leak out of.

Name this part?

What service is being performed?

What parts is this?

Which of these could be the result of a driveshaft being out of phase?

A(n) __________________ is necessary to measure driveline runout.

A lack of lubrication in a differential will cause the differentials axle bearing to heat up and damage the axle seal.

A clicking noise is heard when a vehicle makes sharp turns. Which of these is the MOST likely cause?

If the center support bearing is equipped with a grease zerk, it should be lubricated whenever a(n) __________ is performed.

Select one:

If the driveshaft parts are not marked during disassembly, then an out-of-phase condition could result, and _________ will occur even if the driveshaft is in balance.

Select one:

Inspection of the lug studs should be done in order to look for _____ or thread defects of the lug studs.

Select one:

Tech A says that axle seals are a common source of solid axle fluid leaks. Tech B says that pinion seals are a common source of solid axle fluid leaks. Who is correct?

Select one:

Brake heat that comes from a dragging brake can cause an axle seal to leak.

Select one:

If the axle shafts are being replaced, it is a good practice to replace the ______.

Select one:

_______ of the differential will create a pressure buildup in the differential from foaming of the liquid that the breather cannot handle, so the weakest place to vent pressure will be through the axle seal itself.

Select one:

Driveline angularity is the relationship of the driveshaft to the component that the driveshaft attaches to, as measured in degrees.

Select one:

If a half-shaft type axle is clicking when turning ______, then the joint or the entire half-shaft will need to be replaced.

Select one:

Name this part?

Name this part?

Name this part?

Name this part

Name these parts?

Name this part?

Name this part?

A transfer case is most often used in a(n):

Newer designs in 4WD pickup trucks and SUVs use constant velocity (CV) joint type front axles.

In a 4-wheel drive vehicle, final drives are found:

Tech A says that part time four wheel drive does not use a transfer case. Tech B says that constant-velocity joints are used on some four-wheel drive vehicles. Who is correct?

______ transmits power to the front and rear drive axles at normal drive speed.

Technician A says that driveline binding can be caused by tires that have different circumferences. Technician B says that tires can be shaved to even out tire circumferences. Who is correct?

In all-wheel drive vehicles only two of the wheels are normally powered, typically the rear wheels.

The transfer case is a device designed to split the power from the transmission to the ______ when four-wheel drive is selected.

Technician A says that in all-wheel-drive vehicles, locked differentials are used to ensure ease in driving around curves. Technician B says that a third set of differential gears is used to allow turning and driving into curves. Who is correct?

Select one:

In some vehicles, when the transfer case's low range option is selected, a geared electric motor automatically operates an engagement sleeve splined to the _______.

Select one:

When the transfer case of an all-wheel-drive vehicle is in high range the wheels:

Select one:

Vacuum controls have rubber diaphragms in them, heat and moisture can cause them to deteriorate over time.

Select one:

Technician A says that mechanical shifting controls can wear out over time. Technician B says that vacuum control rubber diaphragms can deteriorate over time. Who is correct?

Select one:

Wheel bearings and hubs are subject to wheel rim offsets that throw off the wheel's scrub _____ and cause premature failure of the bearings and hubs.

Select one:

Four-wheel drive vehicles have either automatic locking hubs or manual locking hubs.

Select one:

What part is this?

What is the smaller lever?