NEW
Font size
WorksheetsGIC 2nd Semester Final Review
Total questions: 38
Worksheet time: 1hrs 3mins
What should be held agianst the fence when cutting on a miter saw?
Hand
Material
Blade
Guard
When overhead work is being completed what PPE should be worn?
Hard Hat
Safety Vest
Tool Belt
Work Boots
To prevent falling off a roof _____ are used.
Toe Boards
Safety Glasses
Gloves
Ladder
Extra precaution needs to be taken when using power tools in..
None at all
in good conditions
In dry conditions
In wet conditions
What is the proper cutting depth setting on a circular saw?
A 1/2'' greater than the material thickness.
A 1/4'' greater than the material thickness.
A 1/8'' greater than the material thickness.
A 3/4'' greater than the material thickness.
What is the proper blade height for cutting a piece of material 2'' thick on the table saw?
2''
2 1/4''
3''
1''
What is the name of the framing member #5
Stud
Sile
Bottom Plate
Double Top Plate
What is the name of framing memeber number #2
Stud
Top Plate
Header
Cripple
What is the name of framing member #3
Double Top Plate
Stud
Header
Sile
What is this?
Speed Square
Hammer
Chaulk Line
Tape Measure
What is this?
Speed Square
Hammer
Tape Measure
Chaulk Line
What is this?
Speed Square
Hammer
Tape Measure
Chaulk Line
What is this?
Table saw
circular saw
Miter saw
Drill
What is this?
Circular Saw
Miter saw
Table Saw
Drill
What id this?
Miter saw
table saw
Hammer
Drill
What most be used when making small width rips on a table saw?
Push stick
Guard
Gloves
Nothing
What must be worn at all times and is a very important safety procedure?
Gloves
Hat
Helmet
Safety Glasses
You should not be on your ____ on the jobsite?
Cell Phone
Wearing Safety Glasses
Bike
Feet
Before adjusting or repairing a tool you suched?
plug it in
unplug it from the power source
Used it
What is the best tool for cutting a board to length?
Table Saw
Coping Saw
Miter Saw
Drill
What would be used to rip a piece of plywood to width?
Miter Saw
Coping Saw
Table Saw
Hand Saw
Select the best tool to cut a 45 degree angle?
Miter Saw
Table Saw
Coping Saw
Drill
What is a stop block used for?
To cut a miter cut
To make mutiple cuts at the same length
Stop fire from spreading
Keep fingers at a safe distance
What is C.
Ridge Board
Rafter
Ceiling Joist
Collar Tie
What is B.
Ridge Board
Rafter
Celing Joist
Collar Tie
What is A.
Ridge Board
Rafter
Ceiling Joist
Collar Tie
What is E.
Ridge Board
Rafter
Ceiling Joist
Collar Tie
The span is the ____ of a building.
height
volume
rise
width
What is a common wall stud layout?
12'' on center
16'' on center
18'' on center
30'' on center
What is the vertical stair member of the stringer?
Tread
Run
Stringer
Riser
How wide should a rough openning be for 2' 8'' entry door?
2' 10''
3'
2' 6''
4'
The walls in Bedroom A are 8' tall. How many gallons of paint would need to be purchased to paint the bathroom if one gallon of paint covers 300 square feet? Round to the nearest gallon. (Exclude Doors and Windows)
1 gallon
2 gallons
3 gallons
4 gallons
If you were to tile the floor in Bedroom D, how many square feet of tile will you need?
130 Square Feet
140 Square Feet
100 Square Feet
115 Square Feet
How many lineal feet of base board trim would be needed for Bedroom C? (Exclude closets , windows, and doors) Round to the nearst foot.
30 FT
40FT
45FT
50FT
If you were building a set of stairs up to a platform that was 112” off the ground and 15 steps how tall would each riser be?
7''
7.25''
7.47''
7.75''
A door is located at the center of a wall. The wall measures 10’ 4 ½”. What is the correct center of the wall dimension?
5' 3''
5' 6''
5' 8 1/4''
5' 9''
What is the run of the building if the span measures 55’ 8 ½”?
27.5'
27' 8 1/4''
27' 10 1/4''
27' 11''
What is the total Rafter length?
88.5''
88.75''
90''
87.5''
