Font size
Worksheetschapter 6
Total questions: 23
Worksheet time: 6hrs 45mins
Holes that are ¼ inch or smaller are said to be ______, while larger holes are said to be ______.
drilled, bored
drilled, sawed
bored, drilled
sawed, drilled
A drill that is twisted at its end
(a)
Has jaws that are adjusted to tightly grip the shank
(a)
Are used to cut holes ¼ inch to 1 inch in diameter
(a)
The end of the auger bit which helps draw the bit into the wood
(a)
The non cutting end of the auger bit
(a)
Comes with a set of drill points provides a quick and easy way to drill small holes
(a)
Used with twist drills to drill small holes, usually ¼ inch or less in diameter
(a)
A part that holds the auger bit
(a)
A feature that allows you to adjust the speed by the amount of pressure you apply to the trigger
(a)
Used to control the depth of the hole being drilled
(a)
Attached to the edge of the stock guide the drill to cut dowel holes that are perfectly straight and perpendicular
(a)
Can be used as an aid for drilling holes that hold two pieces of wood together
(a)
︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎
︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎
︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎
︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎
︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎
︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎ ︎
______ depth stops are more accurate than ______ depth stops.
commercial, handmade
handmade, commercial
The (a) makes it faster to change bits.
(2 words)
On some power drills, a (a) is used to tighten the jaws of the chuck.
(2 words)
The (a) is used for holding auger bits, forstner bits, and other tools with rectangular shaped shanks.
(2 words)
T/F: Most bits for power drills have rounded shanks, and the size of it varies according to the size of the bit.
True
False
Use a (a) or a punch to mark a starter hole.
(2 words)
T/F: The steps with using hand drills and automatic (or push) drills are different.
True
False
T/F: Try squares help keep the bit centered on the workpiece.
True
False
Define variable-speed.
(if you don't know, just get it wrong)
(a)
