Engineers need to ask two of the following questions to extend human capabilities. (09-17 Edpuzzle)

Select the American Society of Civil Engineers Code of Ethics distinct principles from the following. (09-17 Edpuzzle)

The one factor that a scientist changes during an experiment. (It affects the results of the experiment). (10-07 Act. 1.3.2 Experimental)

The variable that is measured. It is the result of the experiment. (10-07 Act. 1.3.2 Experimental)

The factors stay the same throughout the experiment. (10-07 Act. 1.3.2 Experimental)

Ben makes five paper helicopters with different wing lengths. He drops them the same way from a height of two meters for five trials each. He records the amount of time it takes for each helicopter to fall to the ground.

What is the independent variable? (10-07 Act. 1.3.2 Experimental)

Ben makes five paper helicopters with different wing lengths. He drops them the same way from a height of two meters for five trials each. He records the amount of time it takes for each helicopter to fall to the ground.

What is the dependent variable? (10-07 Act. 1.3.2 Experimental)

Cindy wanted to find out how the amount of sunlight affects the growth of plants. She placed two tomato plants in 10 inch pots with potting soil and watered them ¼ cup each day. One plant was placed under a cardboard box and one was placed in the sunlight. She measured the growth of the plant each week for three weeks.

What is the dependent variable? (10-07 Act. 1.3.2 Experimental)

Based on the tensile test graph, B represents the _ of the material.

(10-15 Act. 1.3.3 Notes)

A "complete recovery" occurs during this phase when the material regains its original length when the stress is removed:

(10-15 Act. 1.3.3 Notes)

After these points are exceeded even if the forces are removed immediately the material does not regain its original properties during this phase:

(10-15 Act. 1.3.3 Notes)

During this phase, if the stress is increased further an increasing number of upright dislocations form in the crystal lattice prevents the movement of the previous still sliding dislocations. At the same time, the stress in the crystal lattice continues to increase which causes hardening of the material. Here the metal becomes stronger as the strain increases.

(10-15 Act. 1.3.3 Notes)

In the crystal lattice of the metal bar, so many dislocations have occurred that they can no longer lead to hardening but instead contribute to the formation of voids or cavities. The voids also cause the material cross-section to reduce until it can no longer withstand the stress at point B, better known as the:

(10-14 Calculate Volume)

What is the volume of this figure?

(10-14 Calculate Volume)

What is the volume of this figure?

(10-14 Calculate Volume)

What is the volume of this figure?

(10-19 Edpuzzle: Constraints)

Identified limitations to the design of a product or system are known as:

(10-19 Edpuzzle: Constraints)

Time, budget, and safety are almost always considered to be:

Hint: The company benefits from them to earn a profit while providing a quality product.

(10-19 Edpuzzle: Constraints)

Identified elements and/or features of a product or system are known as:

Hint: Customers set the standards based on their needs, wants, and desires for the system (product).

(10-19 Edpuzzle: Constraints)

A constraint that is concerned with cost and must be considered when designing is:

The retail package is the basic unit in unit loading.

The amount of matter in an object:

It is affected by gravity:

What is the step in the Engineering Design Process where you identify a problem or need that exists?

During which step of the Engineering Design Process do you experiment with the prototype under controlled conditions and collect /record data?

During which step of the Engineering Design Process would the specific constraints or requirements of the challenge be identified?

An emergency-equipment company makes warning-signal flares. The company wants to redesign a flare so that it produces light for a longer period of time.

After the company thinks of ideas, what is the next step in the design process?

Where do engineers store all their ideas?

Choose the correct order for the steps of the Engineering Design Process.

If your initial design doesn't fully solve the problem or meet the challenge, you must go back and revise your plan. This is part of which step in the Design Process?

Engineers plan on developing a new drill for use on oil rigs. What should the engineers do first in order to develop the new drill?

A small group of people starts sharing ideas. Some ideas may seem silly, but all suggestions are written down for further consideration. This activity is part of which step of the Engineering Design Process?

A team of engineers is asked to design a scooter for less than $30. They decide that they will only use recycled materials. Which of the following is the team’s constraint?

What size resistor would produce a 3 Amps current flow with a 12 emf?

What is current measured in?

What is Resistance?

The electricity that flows in a closed path is called a:

What is the Voltage of a circuit that has a resistance of 5 Ω and a current of 2 A?

If the voltage is increased and the resistance stays the same, the current will:

If the voltage stays the same and Resistance is increased, the current will:

If the battery produced 12.6 Volts what would be the current flow for a 6 Ohm resistor?

The first two color bands are........

The third color band is the _.

The fourth color band represents the _.

The gold color band refers to__________tolerance.

If the fourth color band old is gold on a 100 ohm resistor. The range for the tolerance is between_____and ______

What is the median (average) value for the following resistor?

Where did the name "breadboard" come from?

What will happen if you forget to include one of these in the circuit?

What physical quantity does the voltmeter measures?

What physical quantity does ammeter measures?

A tool that measures voltage, current, resistance, and continuity is called a:

On a multimeter, the black probe is connected to the __.

What type of measurement requires the component to be isolated and power removed?

The multimeter should always be set ______ than/with the indicated value.

What will appear to the display if the probes are connected in reverse?

What scale in the multimeter will you choose when you are to measure the voltage of a power outlet?

The place where a lever pivots is called the _______.

What kind of lever is this?

A see-saw is an example of a _-class lever.

A wheelbarrow is an example of a _-class lever.

Which of the two circuits would have the brightest bulbs?

Does this statement best describe a parallel or a series circuit?

When more light bulbs are added they all remain bright.

This circuit does not work because _.

What is the part within the red boxes called?

The "On Shake" Microbit command relies on the:

How many variables have been used in this program?

What name is given to this programming editor that lets you code the Microbit?

The current going through the 45-ohm resistor is

The voltage dropped across the 300-ohm resistor is

What will happen if one light bulb is removed from this circuit?