WorksheetsWorkplace Safety Quiz
Total questions: 20
Worksheet time: 10mins
You are ultimately responsible for your safety, so remember to ________.
always work in a partnership with someone else
work safely
never work in a partnership with someone else
both always work in a partnership with someone else and work safely
A lockout/tagout is an umbrella term that describes a set of safety ________.
tools
equipment
devices
practices and procedures
________ are ideal for measuring valve guides on a cylinder head for wear.
Telescoping gauges
Split ball gauges
Dial bore gauges
Vernier calipers
The ________ micrometer measures the distance between the anvil and spindle, so that is where the part being measured fits.
Inside
Outside
Depth
Standard
When discussing bench grinders, Technician A says that you may install grinding wheels that are smaller than the grinder's rating. Technician B says that eye protection must be worn, and wheel guards and tool rests should be firmly in place. Who is correct?
Technician A
Technician B
Both Technician A and Technician B
Neither Technician A nor Technician B
Technician A states that one of the most common air tools in an automotive shop is the air-impact wrench. Technician B states that removing lug nuts often requires very little torque. Who is correct?
Technician A
Technician B
Both Technician A and Technician B
Neither Technician A nor Technician B
Blasting debris and dirt can be dangerous, so the technician should always ________.
Wear eye protection only
Wear ear protection only
Direct all blasts away from the user and others
All of these are correct
A(n) ________ holds parts together while they are being assembled, drilled, or welded.
J-clamp
Alligator clamp
C-clamp
Vise clamp
________ have expanding grappling fingers on one end to grab items, while the other end has a push mechanism to expand the fingers and a retracting spring to contract the fingers.
Mechanical fingers
Magnetic fingers
Magnetic pickup tool
Mechanical pickup tools
What type of punch is used to drive out rivets or pins?
Brick punch
Drift punch
Center punch
Pin punch
The base measurement for most pressure gauges is atmospheric pressure, which is (a) .
Technicians A says that engine scanners are used to view data from the engine's mechanical components. Technician B says scanners will display test results, data, and in some cases waveforms. Who is correct?
Technician A
Technician B
Both Technician A and Technician B
Neither Technician A nor Technician B
Technician A states that safety needs to be first and foremost when working with an oxyacetylene torch. Technician B states that the acetylene pressure in a full cylinder is approximately 250 psi. Who is correct?
Technician A
Technician B
Both Technician A and Technician B
Neither Technician A nor Technician B
The most common method of propelling the sand or glass beads in a sand or bead blaster is with (a) .
A motor vehicle battery is typically how many volts?
6
12
24
20
Technician A says that when checking continuity with a multimeter, the power supplied to the circuit during operation must be turned on. Technician B says that it does not matter whether the power is on or off. Who is correct?
Technician A
Technician B
Both Technician A and Technician B
Neither Technician A nor Technician B
Gear oil is the lubricant used in __________.
Transmissions only
Transfer cases only
Differentials, transmissions, and transfer cases
Differentials only
Technician A says ultra-low sulfur diesel (ULSD) is commonly used in passenger vehicles in Europe, the USA, and Canada. Technician B says the principal measure of diesel fuel quality is its cetane number. Who is correct?
Technician A
Technician B
Both Technician A and Technician B
Neither Technician A nor Technician B
Where might you find chrome on an automobile?
Battery
Hubcap
Radiator
Engine cylinder blocks
The base substance used for polish is ________.
Wax
Plastic resin
Graphite
Paraffin
