Font size
WorksheetsT.L.E. PERIODIC TEST CARPENTRY 7/8
Total questions: 52
Worksheet time: 52mins
What document should be accomplished to request carpentry tools and materials needed for a task?
Purchase Form
Receiving Form
Requisition Form
Delivery Form
Jason would like to request tools and materials for his carpentry work. What are the data he needs to complete the requisition form?
Plumb-bob
Push-Pull Ruler
Compass
Try Square
Jason is receiving the requested tools, equipment, supplies, and materials in the shop. What should be done if there are problems with the items delivered?
Refuse to receive the items
Contact the vendor
Check the Purchase Order
Review and correct the Receiving Documents
Which of the following should be checked before receiving delivered tools and materials?
quantity of the items
Specification of the items
Physical conditions of the items
d.
All of the above
Arrange the steps in segregating and labeling non-functional tools and equipment correctly.
I
Conduct an inventory of tools and equipment.
II
Record the number of non-functional tools and equipment.
III
Segregate tools that are serviceable or unserviceable.
IV
Report the number of tools and equipment that are non-functional but subject for
repair.
V
Return tools and equipment in the tool cabinet as per operating procedures.
VI
Label tools and equipment which are condemnable.
I, II, III, V, VI, IV
I, II, III, IV, V, VI
V Return tools and equipment in the tool cabinet as per operating procedures.
I, II, III, IV, VI, V
I, III, II, IV, V, VI
Why is it important to inspect and check materials and tools for defects and damage before receiving them?
So that you can ask for replacements for those that you have found defective
So that you can ask for discounts for those that you have found defective
So that you can lessen the hazards and risks in the workplace
So that you can report defective materials and tools
It is the systematic care and protection of tools and equipment to keep them in a safe, usable condition, limit downtime, and extend productivity.
Repairing
Preventive Maintenance
Troubleshooting
Storing
How do we lubricate tools and equipment?
Determine the parts of the machine needed to be lubricated.
Keep the bearing cover closed and apply grease.
Apply the grease on a sealed bearing using bare hands.
Apply a thick coat of oil on the parts for a long period
What will happen if the tools and equipment are NOT well maintained?
The tools and equipment will be kept safe to use.
The downtime of the tools and equipment will be prolonged.
The productivity of the tools and equipment will be extended.
The tools and equipment will be in usable condition.
Which best describes a Zig Zag Ruler?
a foldable measuring tool
used for measuring the diameter
a thin metallic measuring tool
a measuring tool for short pieces of wood
What is the use of a Try Square?
It is used for dividing distances.
It is used for scribing arcs and circles.
It is used for checking the flatness and squareness of materials.
It is used for measuring the diameter.
Jonas will measure the distance from one end of the plywood to another. Which measuring tool should he use?
Push-Pull Ruler
Zig Zag Ruler
Meter Stick
Caliper
Which of the following should NOT be done in handling measuring tools?
Wipe measuring tools before returning them to the storage room.
Oil the movable parts of the measuring tools such as zigzag rules, calipers, etc.
Check the lock of a pull-push rule if it is working.
Wipe off the edges of the steel tape of the pull-push rule with bare hands.
What is the final step in the procedure for checking the conditions of tools and equipment?
Segregating tools by functionality.
Repairing or replacing non-functional tools.
Conducting an inventory of tools.
Returning tools to the tool cabinet.
What information should be recorded during the inventory of tools and equipment?
The number of condemnable tools.
The number of functional tools
The number of non-functional tools.
The location of each tool in the cabinet.
How should non-functional tools be labeled?
Unserviceable
Condemnable.
A report number.
Serviceable
What is the first step in checking the condition of Personal Protective Equipment (PPE)?
Test the functionality of each PPE.
Conduct an inventory of PPE.
Inspect any damaged or defective PPE.
Repair/replace non-functional PPE.
Which portable power tool is primarily used for sanding furniture pieces?
Router
Jigsaw
Sander
Circular saw
What is the primary function of a Screwdriver?
Cutting wood
Driving and pulling out nails
Sharpening edge-cutting tools
Driving and loosening screws
Which tool is used to apply paint or varnish on wood surfaces?
Oil Stone
Files
Paint Brush
Nail Set
Which PPE is used to protect the ears against high-frequency noise?
Gloves
Face Mask
Ear Protector
Apron
What is the purpose of a Spirit Level?
Testing vertical surfaces
Measuring distances
Testing vertical and horizontal surfaces
Cutting irregular shapes
Which type of saw is used to rip, cross, and cut curves in lumber.?
Cross Cut Saw
Turning Saw
Dovetail Saw
Rip-saw
What is the primary function of a C-Clamp?
Sharpening edge-cutting tools
Holding materials in place
Driving and pulling out nails
Making holes in wood
What should be done after identifying non-functional PPE?
Separate functional and non-functional PPE.
Report the condition or status of PPE.
Test the functionality of each PPE.
Label the condemnable PPE.
Which tool is used to drill holes of various sizes in wood?
Auger bit
Expansive bit
Drill Bit
Expansive bit
What type of tool is a Marking Gauge?
Edge cutting tool
Marking lining tool
Testing tool
Measuring tool
What is the function of a Claw Hammer?
Cutting wood
Sharpening edge cutting tools
Driving and pulling out nails
Making holes in wood
Which PPE is used to protect the eyes against flying debris and harmful liquids?
Gloves
Goggles
Ear Protector
Face Mask
Which portable power tool is used for shaping surfaces and edges of furniture parts?
Sander
Jigsaw
Router
Circular saw
What is the primary function of an Oil Stone?
Applying paint or varnish
Sharpening edge cutting tools
Drilling holes
Cutting irregular shapes
Which measuring tool is used to measure the distance between two opposite sides of a surface?
Pull-Push Rule
Ruler
Try Square
Caliper
Which tooth-cutting tool is used for cutting irregular shapes in small boards?
Dovetail Saw
Compass Saw
Turning Saw
Coping Saw
Which tool is used to establish a straight line on a surface?
Chalk Line
Compass
Divider
Marking Gauge
It is a rectangular piece of steel with two cutting edges used for working flat and curved shapes.
Cabinet scraper
Spoke shave
Plane
Chisel
Which of the following working conditions does NOT produce hazards?
Falling objects
Toxic Chemicals
Heat and dust
Spacious work area
Jonas would like to ensure the safety of the construction workers. Which of the following should he use?
Signs, signals, and barricades
Danger signs
Exit signs
Safety instructions signs
Your employer must conduct a hazard assessment in order to ___________.
avoid absences
promote accidents
eliminate workers
reduce risks
OSH means _______________.
Occupational Service Healthy
Occupational Safe and Healthy
Occupational Safety and Health
Occupational Safe and Health
Accidents can be prevented through ______________.
the use of expensive tools and equipment
right attitude toward work
adhering to safety practices
wearing of uniforms
Anna needs to pull out a piece of nail. Which tool does she need?
Try-Square
Claw Hammer
Mallet
Level Bar
Which carpentry material is a thin cross laminated sheet of wood?
Lumber
Timber
Plywood
Log
Which saw can be used to cut pipes and metals?
Rip Saw
Cross-cut Saw
Chain Saw
Hacksaw
What carpentry tool is used in cutting lumber or board across the grain?
Chisel
Cross-Cut Saw
Hack Saw
Electric Drill
Which measuring tool is best used to measure long materials?
Push-pull rule
Caliper
Divider
Ruler
Jason will make a vertical reference line. What carpentry tool should he use?
Plumb-bob
Push-Pull Ruler
Compass
Try Square
Which of the following is NOT a role of a carpenter?
Interpreting drawings to create an item or component.
Laying out or designing items or components.
Cutting or shaping timber using hand or power tools.
Installing electrical wirings.
Mary needs to re-attach the legs of her wooden chair. Which material should she use to fasten the wooden parts together?
Nails
Ropes
Metal Cables
Zip Ties
Which of the following is a powdered substance which, when mixed with water, acts as a binder of aggregates?
Sand
Cement
Gravel
Plaster
Which of the following carpentry tools should be used for cutting along the grain?
Rip Saw
Chisel
Hack Saw
Cross-Cut Saw
Full Name
Section
