NEW
Font size
WorksheetsAircraft Safety and Operations
Total questions: 30
Worksheet time: 30mins
What must be attached to devices that should not be operated for safety reasons?
Red warning signs
Green warning signs
Yellow caution signs
Blue information signs
What should be done to circuit breakers for safety?
Leave them open
Label them with warnings
Remove them completely
Secure them with safety clips
What is forbidden when working on high platforms?
Using safety harnesses
Cleaning icy ladders
Positioning stairs and ladders on working platforms
Installing balustrades
What should be done to prevent tools from falling when working at height?
Hold them while working
Locate them securely
Leave them on the ground
Drop them safely
What is a potential hazard on the apron?
Rolling and towing movements
Static vehicles
Calm weather conditions
Low noise levels
What must be done before entering on the apron?
Inspect the aircraft
Check the weather
Wear a helmet
Complete a safety briefing
What does FOD stand for?
Flight Object Damage
Foreign Operations Directive
Flight Operations Directive
Foreign Object Damage
What should be done at the end of a shift regarding tools?
Hide them from view
Leave them as they are
Clean and organize the work area
Give them to a colleague
What is a requirement when using ladders?
They must be secured from falling
They should be used without inspection
They can be placed at any angle
They can be defective
What should be done if a device is defective?
Continue using it
Ignore the defect
Report it to a colleague
Initiate its repair
What does the red light under the aircraft fuselage being on indicate?
Prepare for takeoff
Stay clear of the aircraft
Move closer to the aircraft
Engines will be started soon
What should be done to ladders in icy conditions?
Use them as they are
Leave them outside
Clean them from ice and snow
Ignore the conditions
What is the highest possible work area mentioned?
The ground level
The wing tips
The upper end of the vertical stabilizer
The cockpit
What is a key responsibility of employees regarding tools?
To lend them to others
To maintain and keep them organized
To leave them wherever
To use them without care
What should be done AFTER the connectors for the electrical control are removed?
document it only
reconnect after finishing the work
Document it AND reconnect after finishing the work
No need to do anything
What should be done if a safety harness is found to be damaged?
Continue using it
Report it immediately
Repair it on-site
Store it away
What should be done if a spill occurs on the apron?
Ignore it
Report it and clean it up
Cover it with sand
Leave it for maintenance
What is a common cause of Foreign Object Damage (FOD) in aviation?
Weather conditions
Improper maintenance
All of the above
Loose tools and equipment
How can personnel minimize the risk of FOD during aircraft maintenance?
By using larger tools
By working quickly
By keeping the work area clean
By wearing gloves
What should be done if a foreign object is spotted on the runway?
Try to remove it yourself
Take a picture of it
Report it immediately
Ignore it
What should be done if a tool is found to be missing?
Search for it immediately
Report it to a supervisor
Assume it is lost
Ignore the situation
What is the purpose of using safety cones on the apron?
All of the above
To direct traffic
To indicate hazards
To mark safe zones
What should be done if a ladder is found to be unstable?
Ignore the instability
Adjust it until it feels stable
Report it and do not use it
Use it anyway
What should be done if a safety cone is knocked over on the apron?
Leave it as is
Report it immediately
Set it back up
Ignore it
What should be done if a colleague is seen not wearing required safety gear?
Ignore the situation
Report it to a supervisor
Advise them to wear it
Join them in not wearing it
What is the primary purpose of safety vests on the apron?
To protect from rain
To indicate rank
To enhance visibility
To keep workers warm
What should be done if an aircraft is being towed on the apron?
Stand in its path
Clear the area and stay alert
Take a photo for documentation
Ignore it
What is a critical action to take when working near moving vehicles on the apron?
Run to the vehicle
Make eye contact with the driver
Wave to the driver
Stand still and wait
What is the primary purpose of conducting a pre-maintenance safety briefing?
To ensure all personnel are aware of potential hazards
To assign tasks
To review maintenance schedules
To socialize with colleagues
What should be done if a maintenance task requires working in a confined space?
Proceed without precautions
Use appropriate safety equipment and follow protocols
Ask a colleague to do it
Ignore the confined space warning
