WorksheetsInspection of Rainwater Systems
Total questions: 56
Worksheet time: 28mins
What should you inspect before starting work on rainwater systems?
The color of the roof
The straightness and level of the facia boards
The type of paint used
The size of the gutter
Why is it important to inspect the underfelt of the roof?
To ensure it matches the facia board
To prevent rainwater from dripping behind the facia board
To check for color consistency
To measure the thickness of the roof
What should be done if the facia board is not straight?
Ignore it
Paint it
Replace it
Adjust the gutter
Which of the following tools is required for the installation of rainwater systems?
Paintbrush
Power drill
Tape measure
Sandpaper
What type of screwdriver is needed for installing rainwater systems?
Flathead screwdriver
Pozidrive screwdriver
Phillips screwdriver
Torx screwdriver
Which tool is used for cutting during the installation of rainwater systems?
Claw hammer
Hacksaw
Bradawl
File
Which tool is used to ensure a straight line during the installation of rainwater systems?
String line
Claw hammer
File
Bradawl
What is the first step in the installation of a rainwater system?
Tie the string line on the first facia bracket
Establish the position of the outlet
Measure the overall length
Fix the first facia bracket
How should the fall be worked out when measuring the overall length?
1:500
1:600
1:700
1:800
Where should the string line be tied during the installation process?
On the gutter
On the outlet
On the first facia bracket
On the drain
What is the first step in installing a rainwater system according to the document?
Screw the running outlet in position
Move the running outlet down the calculated measurement
Place the string level on the string and level up the running outlet
Secure the string line around the running outlet
Why is it important to tightly secure the string line around the running outlet?
To prevent the outlet from moving
To ensure the string does not break
To show the fall and the position of all the facia brackets
To make the installation look neat
What is the maximum distance apart that fascia brackets should be secured in a standard location?
1.0m
0.5m
1.5m
2.0m
In a windy location, what is the maximum distance apart that fascia brackets should be secured?
0.8m
1.2m
1.5m
2.0m
What is the first step in installing a rainwater gutter system according to the diagram?
Pull the front of the gutter down.
Locate back of gutter up into back locking clip.
Clip the front of the gutter with the locking clip.
Identify the back locking clip location.
Which part of the gutter is clipped using the thumb according to the instructions?
Back of the gutter.
Side of the gutter.
Front of the gutter.
Bottom of the gutter.
What is the recommended fall ratio for rainwater system installation?
1:500
1:600
1:700
1:800
How far apart should facia brackets be placed in a rainwater system?
0.5m
1.0m
1.5m
2.0m
What is the lowest point of a rainwater system run?
Facia bracket
Clip joint
Running outlet
Gutter
What type of screws should be used in rainwater systems to prevent corrosion?
Aluminum screws
Brass screws
Stainless steel screws
Copper screws
What tool should be used to cut gutters in a rainwater system?
Circular saw
Fine tooth (24tpi) hacksaw
Jigsaw
Chainsaw
When installing gutter angle fittings, how far should facia brackets be fitted from the fittings for additional support?
100mm
150mm
200mm
250mm
Which type of bracket is used when a building does not have facia boards for gutter installation?
Top fitted rafter brackets
Side fitted rafter brackets
Rise and fall brackets
Bottom fitted rafter brackets
What is the first step in the installation of a downpipe according to the document?
Cut a length of downpipe
Measure the distance between the two 112.5° bends
De-burr the downpipe
Solvent weld the downpipe
What might be needed when forming a swan-neck with a downpipe?
Painting
Solvent welding
Sanding
Drilling
Fill in the blank: The diagram shows a ______.
circle
square
triangle
rectangle
What is the first step in the installation of a downpipe according to the document?
Cut pipe to length and de-burr
Measure vertical distance to shoe or drain connector
Install in position
Check the manufacturer's clipping distances
What is the recommended vertical clipping distance for a 68mm pipe?
1.0m
2.0m
1.5m
2.5m
What is the recommended horizontal clipping distance for a 68mm pipe?
1.0m
1.5m
1.2m
2.0m
What is the purpose of rainwater pipe to drain connections?
To connect rainwater pipes to the main water supply
To connect rainwater pipes to the drainage system
To connect rainwater pipes to electrical systems
To connect rainwater pipes to heating systems
What is the function of rainwater pipe clips?
To secure rainwater pipes in place
To filter rainwater
To heat rainwater
To measure rainwater flow
What is the purpose of testing a rainwater system after installation?
To ensure it is watertight and performs well.
To check the color of the water.
To measure the temperature of the water.
To see if the system makes noise.
What should be used to test the flow of water in a rainwater system?
A bucket of water or hosepipe.
A thermometer.
A pressure gauge.
A sponge.
What should you inspect for when testing a rainwater system?
Leaks and pooling in the gutter.
The color of the gutter.
The weight of the gutter.
The length of the gutter.
What is a key safety consideration when working at heights during rainwater system installation?
Always work alone for better focus.
Use a ladder without a stand off.
Always risk assess the job.
Ignore weather conditions.
What should you avoid doing when the weather is bad during installation?
Attempt the job alone.
Use fixed scaffolding.
Work from a tower scaffold.
Assess the risks.
What is one of the first steps to take when installing rainwater systems?
Start the installation immediately
Secure the area and put up warning signs
Ignore existing property damage
Work without notifying the customer
Why is it important to identify existing damage to the customer's property before installation?
To charge extra fees
To ensure the customer is aware of any pre-existing issues
To avoid doing any work
To speed up the installation process
What should be used to avoid damaging the building fabric during rainwater system installation?
A stand-off
A ladder
A tarp
A hammer
What should be done to prevent a ladder from sinking into a customer's lawn?
Use a stand-off
Use a wider ladder
Avoid using a ladder
Place a board under the ladder
What should you ask the customer to do with nearby vehicles during installation?
Cover them with a tarp
Move them away
Park them closer
Leave them as they are
What precaution should be taken when working in a public place?
Work at night
Use a stand-off
Place barriers around
Avoid using ladders
What is the correct angle to set a ladder for safety when working at heights?
60°
75°
90°
45°
How far should the top of the ladder extend past the top of the working platform?
0.5 metres
1.07 metres
2 metres
0.75 metres
Which of the following should you avoid using when working at heights?
New ladders
Damaged ladders
Wooden ladders
Metal ladders
What should you do to the top of the ladder to ensure safety?
Paint it
Lash it
Remove it
Shorten it
Why is maintenance essential for rainwater systems?
To keep the system working effectively
To increase water pressure
To reduce water usage
To change the water color
What does PPM stand for in the context of rainwater system maintenance?
Planned Preventive Maintenance
Periodic Performance Management
Public Property Maintenance
Personal Property Management
How often should rainwater systems be checked in domestic properties?
Annually
Monthly
Weekly
Daily
What should be done visually during the maintenance of rainwater systems?
Check the overall condition and list any specific problems
Paint the system
Replace all parts
Increase the water flow
What is the recommended remedy for leaks in rainwater systems?
Replace section or fitting
Remove bolt, clean joint, replace seal, re-bolt joint
Carry out rectification according to type of system and material
Remove items and flush out, maybe fit a gutter guard
How should a leak in a cast iron joint be fixed?
Replace section or fitting
Remove bolt, clean joint, replace seal, re-bolt joint
Correct facia bracket distance
Inadequate guttering, additional downpipes
What is the solution for a damaged gutter?
Replace section or fitting
Remove items and flush out
Correct facia bracket distance
Inadequate guttering, additional downpipes
What should be done to address blockages in rainwater systems?
Replace section or fitting
Remove items and flush out, maybe fit a gutter guard
Correct facia bracket distance
Inadequate guttering, additional downpipes
What is the maximum correct facia bracket distance for a sagging gutter?
0.5m
1.0m
1.5m
2.0m
What is a possible remedy for an overflowing gutter when raining?
Replace section or fitting
Remove bolt, clean joint, replace seal
Inadequate guttering, additional downpipes or deep flow guttering
Correct facia bracket distance
