wayground logo

Free Printable Worksheets

Font size

S
M
L
XL
Worksheets

System Components quiz

Total questions: 26

Worksheet time: 14mins

Name
Class
Date
1.

What is the Image shown

a)

Still

b)

Air Separator

c)

Bypass valve

d)

Slimline Boiler

2.

Where is the neutral point

a)

At the edge of the Klingon empire

b)

Where the open vent connects to the circuit

c)

Where the primary flow becomes the return

d)

Where the cold feed connects to the circuit

3.

What is the image shown used for?

a)

Clearing the pump

b)

Venting the boiler interlock

c)

Charging the radiators

d)

Bleeding the radiators

4.

What is this component?

a)

Blank cap

b)

Bleed valve

c)

Automatic air vent

d)

Expansion vessel

5.

What is the purpose of this component in a central heating system

a)

Fills hot water cylinder

b)

Controls water level in cold water storage cistern

c)

Fills combination boiler

d)

Controls water level in feed and expansion cistern

6.

Name this component

a)

Room thermostat

b)

Programmer

c)

Cylinder thermostat

d)

Remote sensor

7.

Identify this component

a)

Pressure relief valve

b)

Radiator valve

c)

Lockshield valve

d)

Automatic air vent

8.

What is this component?

a)

Feed and expansion cistern

b)

Cold water storage cistern

9.

What is the normal capacity of this component?

a)

4 Litres

b)

10 Litres

c)

18 Litres

d)

24 Litres

10.

Which system of control would this item be used with?

a)

C plan

b)

C plan +

c)

S paln

d)

Y plan

11.

What is this component used for?

a)

Filling a low pressure heating system

b)

Filling a high pressure heating system

12.

What would this component be connected to?

a)

Radiator

b)

Hot water cylinder

c)

Expansion vessel

d)

Central heating pump

13.

Identify the lockshield radiator valve

a)
b)
c)
d)
14.

Identify the thermostatic radiator valve

a)
b)
c)
d)
15.

What is the purpose of locking out in a boiler?

a)

To increase the efficiency of the boiler

b)

To regulate the air pressure in the system

c)

To protect the boiler from overheating

d)

To control the flow and return temperature

16.

Which type of system uses one zone valve to control the hot water and a second zone valve to control the heating circuit?

a)

Fully pumped two two-port valves – S plan system

b)

Fully pumped mid-position valve – Y plan system

c)

Pumped central heating only

d)

Two-pipe semi-gravity with heat sink

17.

Name the component

a)

programmer

b)

cylinder thermostat

c)

boiler thermostat

d)

room thermostat

18.

A property above how many m2 should have more than 1 zone?

a)

100 m2

b)

150 m2

c)

200 m2

d)

250 m2

19.
Question Image

Match the following

a)

A

1.

System under negative pressure

b)

B

2.

System under positive pressure

c)

C

3.

Correct arrangement

20.

What does a Magnaclean do

a)

Removes limescale in a boiler

b)

Remove iron oxides

c)

Collects iron oxide

d)

Reduces magnetic fields in a system

21.

What one of these components is NOT installed on a sealed heating system

a)
b)
c)
d)
22.

What is the cause of corrosion within a central heating system?

a)

Aeration

b)

Overheating

c)

Low system pressure

d)

Excessive water flow

23.

Which one of the following would be included in a sealed central heating system?

a)

Expansion Vessel

b)

F& E System

c)

Pressure reducing valve

d)

Cold Water Storage Cistern

24.

Identify what type of system is shown here.

a)

C plan plus

b)

Semi gravity system

c)

Unvented system

d)

Full gravity pumped system

25.

On a three port mid-position valve, what does port 'A' supply?

a)

The boiler

b)

Central heating circuit

c)

F&E cistern

d)

Hot water circuit

26.

The symbol shown here can be identified as?

a)

Single check valve

b)

Double check valve

c)

Service valve

d)

Circulator