WorksheetsAUT-103 FINAL WRITTEN EXAM
Total questions: 42
Worksheet time: 21mins
What is a consequence of running a transmission low on gear oil?
It improves fuel efficiency.
It enhances the vehicle's speed.
It wears out quickly and needs to be rebuilt or replaced.
It reduces engine noise.
What is the nature of the job when rebuilding a transmission or transaxle?
Simple and quick
Complex and huge
Inexpensive and easy
Routine and minor
What are common issues that can occur as manual transmissions/transaxles wear?
They may pop out of gear
They may improve fuel efficiency
They may become quieter
They may increase horsepower
What should you rely on to diagnose issues with manual transmissions/transaxles?
Customer information and road-testing
Visual inspection only
Engine performance data
Tire pressure readings
What is a key step in diagnosing transmission noises?
Check diagnostic info in the service information system
Replace the transmission fluid
Adjust the tire alignment
Inspect the exhaust system
What is a possible root cause of failure in manual transmissions?
Worn synchronizer rings
New bearings
Intact gaskets
Strong detent spring
Which of the following hard parts may need to be replaced in a manual transmission?
Brake pads
Input/output shafts
Fuel injectors
Radiator hoses
Where can a noise come from in a vehicle, other than the manual transmission/transaxle?
Engine
Exhaust system
Fuel tank
Battery
Which of the following is NOT a potential source of noise in a vehicle?
Transfer case
Differential
Motor mounts
Windshield
Which of the following is NOT a cause of grinding noises during shifting?
Driver not fully pushing down clutch
Synchronizer blocker rings needing replacement
Shift rail binding and engaging two gears at once
Properly aligned bell housing
What might cause rough growling noises while driving?
Worn bearings/gears
Worn throw-out bearing
Worn pilot bearing
Input bearing
Which component is likely worn if rough growling noises occur in neutral with the clutch lightly pushed?
Input bearing
Worn throw-out bearing
Worn pilot bearing
Countershaft bearings
If rough growling noises occur in neutral with the clutch fully pushed down, what is the likely cause?
Worn throw-out bearing
Input bearing
Worn pilot bearing
Pocket bearings in the input shaft’s back
What should you do if the gears are hard to shift in a manual transmission?
Check the brake fluid
Lift the vehicle’s wheels
Replace the transmission
Adjust the seat position
If the wheels spin when the clutch is pressed, what should be checked?
Brake pads
Clutch adjustment
Tire pressure
Engine oil level
What is one possible issue to check for in a hydraulic clutch system?
Low battery charge
Air in the system
Faulty spark plugs
Worn-out tires
Which maintenance issue could lead to shifting problems in a manual transmission?
Regular oil changes
Improper transmission fluid maintenance
New detent ball installation
Upgraded shift linkages
What could be a result of a worn shift lever in a manual transmission?
Improved gear engagement
Difficulty in shifting
Reduced engine noise
Increased vehicle speed
A jammed synchronizer in a manual transmission might be caused by what?
Broken dog teeth
Low oil level
Faulty alternator
Worn out tires
What could be a cause of a manual transmission jumping out of gear related to the shift mechanism?
Worn/broken powertrain mounts
Shift linkage or shift cable issues
Synchronizer’s blocking ring
Dog teeth wear
Which component outside the transmission might affect the gear engagement due to synchronizer issues?
Shift fork
Powertrain mounts
Shifter boot
Shaft movement
What can happen to a front-wheel drive (FWD) vehicle if it is driven roughly?
The engine overheats
The constant-velocity (CV) joints or boot may get damaged
The tires wear out quickly
The battery drains faster
What should be checked if there are noises or vibrations coming from the transaxle?
The vehicle's paint job
The vehicle's TSBs and service information
The vehicle's fuel type
The vehicle's interior design
Why is it important to know the root cause before disassembling a failed transmission/transaxle?
To save time on repairs
To ensure an error-free repair
To avoid using TSBs
To reduce the cost of parts
If the issue is not with the transmission, what should be checked next?
Engine oil
Drivetrain
Brake fluid
Tire pressure
When using a scan tool for codes a customer is concerned about, what should you follow?
User manual
Troubleshooting chart
Customer feedback
Online tutorials
What should you avoid spending time on when diagnosing manual transmission issues?
Codes unrelated to customer’s concerns
Codes related to customer’s concerns
Manufacturer guidelines
Vehicle maintenance history
What is the most important aspect to consider when disassembling and inspecting a manual transmission?
Attention to every detail
Speed of disassembly
Cost of parts
Brand of the transmission
Which tool is used to apply pressure to bearings during the inspection of a manual transmission?
Slide hammer
Bearing press tools
Wire cutter
Screwdriver
What is the function of a bushing driver kit in manual transmission maintenance?
To remove seals
To install bushings
To cut metal
To measure temperature
Which of the following symptoms may indicate a failing synchronizer in a manual transmission?
Unusual tire wear
Difficulty engaging gears
Low battery voltage
Excessive engine vibration
What should be inspected if a manual transmission is making a whining noise while driving?
Transmission fluid level and condition
Headlight alignment
Windshield wipers
Air conditioning system
Which tool is commonly used to remove a stubborn gear from a manual transmission shaft?
Oil filter wrench
Gear puller
Feeler gauge
Torque wrench
What is a common symptom of a worn input shaft bearing in a manual transmission?
Whining noise during acceleration
Brighter dashboard lights
Decreased fuel consumption
Improved shifting smoothness
Which of the following should be checked first if a manual transmission is difficult to shift into reverse?
Air filter
Headlight bulbs
Windshield wipers
Clutch operation
What is the purpose of synchronizer rings in a manual transmission?
To match gear speeds for smooth engagement
To increase engine power
To lubricate the clutch
To cool the transmission fluid
Which of the following could cause a manual transmission to grind when shifting into first gear?
Worn synchronizer
Properly adjusted shift linkage
New clutch disc
Full transmission fluid
What is a likely symptom of a failing pilot bearing in a manual transmission system?
Transmission fluid leaking
Noise when clutch is fully depressed
Headlights dimming
Clutch pedal feels soft
Which step should be performed before removing a manual transmission for repair?
Install new tires
Check for related technical service bulletins (TSBs)
Adjust the radio settings
Replace the battery
Which component should be inspected if a manual transmission is leaking fluid?
Exhaust manifold
Battery terminals
Windshield wipers
Transmission seals
What is a likely cause if a manual transmission makes a clunking noise when shifting gears?
Worn universal joints
New clutch fluid
Properly adjusted mirrors
Clean air filter
Which of the following can help prevent premature wear in a manual transmission?
Using incorrect gear oil
Regularly checking and changing transmission fluid
Ignoring unusual noises
Driving with the clutch partially engaged
