Worksheets2W0X1 CDC’s Module 4 Review Exam
Total questions: 93
Worksheet time: 47mins
Before using an electric drill, what is the first thing you should do?
Make sure the diameter of the hole to be drilled is within the capacity of the drill
Connect the drill to the power source
Ask a coworker for assistance
Insert the chuck key
The purpose of cutting lubricant in most drilling operations is to increase the
life of the drill only.
speed of drilling only.
frictional heat during drilling.
drilling speed and the drill bit life.
Which minimum articles of safety gear must be worn when using a bench grinder?
Apron and gloves
Eye and face protection
Gloves and steel-toed boots
Safety glasses and long sleeved shirt
An electric saw blade must be operating at what speed before it contacts the material being cut?
Full
Low
Moderate
Accelerated
How many pounds per square inch (psi) of clean, dry air is required at the tool end of the air hose to ensure the tool is operating safely and efficiently?
60
90
110
125
What condition would prevent an operator from applying power to a hoist or other powered lifting device?
An Air Force (AF) Form 979 is attached to the unit.
Potential for lightning within 15 miles of the area.
Procedures are not covered in detail in the owner’s manual.
The unit is tagged with a Department of Defense (DD) Form 1574–1, condition code A.
What should be worn anytime there is a potential for injury from overhead objects during a lifting operation?
Kevlar
Safety goggles
Leather gloves
Protective helmets
What is the most common type of lifting sling used in the munitions career field?
Chain assembly
Web strapping
Metal mesh
Wire rope
The following are all good safety practices to follow when using a lifting sling except
standing clear of the attached load.
padding any sharp corners the sling may come in contact with.
keeping your hands and fingers from between the sling and the load.
inspecting the sling by passing your bare hand over the body of the sling.
The annunciatiors displayed on the Fluke 8025-series multimeter are used to distinguish among
ohms, milliohms, and kilohms.
ohms, kilohms, and megohms.
amps, ohms, and millivolts.
ohms, volts, and amps.
What are the two operational modes of the fluke 8025-series multimeter?
Alternating current and direct current
Range and hold
Auto and manual
Continuous and momentary
The steering system on the MHU-141/M trailer has a turning radius of how many degrees?
20
40
100
200
When the MHU-141 trailer is loaded or towed with the hinged deck panels open, what must be done?
The deck-panel supports must be properly positioned and locked in place with quick-release pins
The deck-panel supports must be properly positioned and held in place with a tie-down strap
Bomb chicks must be positioned to the deck-panels and locked in place with cotter pins
Close and lock the two deck panels; the trailer cannot be towed in this configuration
What is the maximum load capacity of the MHU-110/M trailer?
5,000 pounds
5,500 pounds
15,000 pounds
20,000 pounds
The parking brake on the MHU-110/M is applied by
pulling either one of the two hand levers located on each side of the front of the trailer.
pulling either one of the two hand levers located on each side of the rear of the trailer.
pulling the center hand lever located in the front of the trailer.
pulling the surge brake located on the tongue of the trailer.
How many openings (hinged door panels) are on the deck of the MHU—226 trailer?
One
Two
Three
Four
What type of steering aids the MHU—226 in a tighter steering radius?
Rack and pinion
Power recirculating ball
Front-wheel automotive type
Four-wheel double Ackerman
After 463L pallets are positioned on a rollerized trailer, what can you use to secure the pallets to the trailer?
Steel chains only
Wire ropes and slack adjusters
Word bracing and tie-down straps
MB—1 chain assemblies and/or tie-down straps
What kind of movement supports on-base activities to or from the flightline?
Hazardous cargo
Operational
Logistical
Intrabase
What munitions item is not loaded into transport modules by munitions personnel?
BDU-33
MK 106
ALE-50
20 MM
What transport module used for chaff/flare munitions has a maximum capacity of 40 magazines?
BDU-33
ALE-50
ALE-40
20 MM
How often should the positive locking devices on the doors of munitions transport modules be checked?
At the beginning and ending of each shift
During initial pre-check of the trailer only
After loading, unloading, and periodically between stops
After loading, unloading, and every 10 minutes when transporting
The purpose of the transport beam beneath the lift arm assemblies on the MJ—1 series lift truck is to
provide added stability and to decrease hydraulic pressure from the lift boom when carrying maximum capacity loads over long distances.
provide added support and to relieve hydraulic pressure from the lift arms when carrying loads for long distances.
relieve excess pneumatic pressure from the lift boom when the lift truck is parked.
relieve excess hydraulic pressure from the lift boom when the lift truck is parked.
What is the lifting capacity of the MJ—1 series lift truck?
3,000 pounds
3,500 pounds
6,000 pounds
6,500 pounds
What is the lifting capacity of the MHU—83-series lift truck?
3,000 pounds
3,500 pounds
6,000 pounds
7,000 pounds
When using the MHU—83-series lift truck with fork adapters, you immediately
reduce its lifting capacity by 800 pounds.
increase its lifting capacity by 800 pounds.
reduce its lifting capacity by 1,000 pounds.
increase its lifting capacity by 1,000 pounds.
What happens when you release the accelerator pedal on a vehicle driven with a hydrostatic transmission?
The lift truck stops immediately
The unit rolls until its inertia is spent
The unit coasts to a stop very quickly
The transmission automatically drops to a lower gear
What is the primary drawback to using the hydraulic hand pump to build hydraulic pressure on the MHU—83-series lift truck?
Very labor intensive
Difficult to make fine adjustment to the table
Extremely slow way to build hydraulic pressure
Possible to damage hydraulic system due to over pressurization
How is the yaw positioning from the cradle or boom controls of an MJ—1 lift truck adjusted?
Pneumatically
Hydraulically
Electrically
Manually
What category or categories are Air Force air compressors classified?
By application
High or low pressure
Self-propelled or towed
Powered or non-powered support equipment
The primary difference between a bobtail and a pickup truck is the
bobtail provides a smoother ride.
bobtail is designed for long-distance towing.
bobtail’s back end is shortened by about one-half.
bobtail’s front wheel base is smaller for better turning radius.
What is the purpose behind good operator maintenance of all assigned vehicles?
Mission readiness
Reduce maintenance cards
Maintain vehicle serviceability at reduced cost
Make sure vehicles are serviceable and in good condition
What two components make up a pintle assembly?
Tow vehicle and pintle hook
Trailer and lunette ring
Lunette ring and pintle hook
Tow vehicle and trailer
Pintle safety locking pins must remain attached to the pintle assembly
to prevent an unsecure pin from coming out and getting lost.
to ensure it is available if needed.
by a nonconductive material.
by a bungee cord.
What gear range should be selected in a tractor with an automatic transmission while going downhill?
Neutral
Low range
High range
Any range is acceptable
What is the purpose of the trailer hand valve (Johnson bar)?
Test the trailer brakes
Slow the tractor on wet pavement
Slow the tractor to prevent skidding
To drift the trailer into the right trajectory when you make a turn too sharp
What are hose couplers (glad hands) used for on tractor/trailer combinations?
To connect the service and emergency brake airlines from the tractor to the trailer
To connect the service brake airline with the emergency brake airline
To secure the airlines to the tractor to avoid them from dragging
To join sections of service brake airlines on the trailer
Which procedure is not a consideration for backing a tractor/trailer combination?
Use a spotter
Use mirrors on both sides
Turn toward the driver’s side
Turn toward the passenger’s side
What is the maximum depth of water you may drive a rough-terrain forklift through?
Three feet
Five feet
Seven feet
Eight feet
What is the most beneficial attribute of using the swingmast forklift?
Operates inside due to its quiet running engine
Allows you to maximize the available storage space
Moves bigger assets quickly due to its increased weight limitation
Empties International Shipping Organization (ISO) containers quickly
With the forks level, what is the maximum reach of the variable-reach forklift?
15 feet
16 feet
20 feet
22 feet
What United States Air Force (USAF) gun system is l
oaded and unloaded by the linkless ammunition loading system (LALS)?
The GAU—2B/A, 7.62 millimeter (mm) machine gun
The M197, 20 mm gatling gun
The GAU—8A, 30 mm cannon
The M61A1, 20 mm cannon
Which weapons replaceable assembly of the linkless ammunition loading system (LALS) has no moving parts?
Conveyor
Transfer unit
Trailer chassis
Storage container
Which subassembly of the universal ammunition loading system (UALS) houses a remaining indicator window that provides the means to visually determine the approximate number of rounds in the unit?
Inner drum
Outer drum
Middle drum
Interface unit
Which subassembly of the universal ammunition loading system (UALS) provides the means to load live rounds into the aircraft gun system?
Inner drum
Outer drum
Interface unit
Ammunition conveyor
Which subassembly of the universal ammunition loading system (UALS) provides the power that cycles the rounds through the system?
Inner drum
Outer drum
Interface unit
Pneumatic regulator
How often should the universal ammunition loading system (UALS) replenisher assemblies be inspected?
Every 30 days when in use and annually when in storage
Every 45 days when in use and annually when in storage
Every 60 days when in use and annually when in storage
Every 90 days when in use and annually when in storage
Which subassembly on the universal ammunition loading system (UALS) replenisher assembly prevents accidentally loading a spent cartridge into the loader assembly?
Drive assembly
Delinker loader unit
Empty space preclusion device
Rigid ammunition chute assembly
Which tool can initiate cycling ammunition through the universal ammunition loading system (UALS) replenisher manually?
1/4-inch speed wrench
1/2-inch speed wrench
1/4-inch ratchet and socket
1/2-inch ratchet and socket
What happens to the unfired rounds returning from the loader when the linked ammunition is being processed?
Manually separated and counted for the next upload
Automatically counted and then uploaded back into the loader
Manually downloaded through the second gate in the bottom of the replanisher
Automatically downloaded through the second gate in the bottom of the replenisher
Which 30 millimeter (mm) cannon in internally mounted in the A—10 aircraft.
M39
M61
GAU-8/A
GPU-5/A
During in-shop maintenance, which equipment provides power to the GFU—7/E ammunition loader assembly (ALA)?
GFU-8/E
GFU-9/E
GFU-10/E
GFU-11/E
Which component of the munitions assembly conveyor (MAC) can be used as a forklift adapter to raise the gantry to full height?
Gantry
Rail conveyor
Pneumatic hoist
Interface control board (ICB)
What are the weight capacities of the pneumatic hoists that are attached to the gantry’s I-beam of the munitions assembly conveyor (both versions)?
4,000 lbs.(A/E32K—3, MAC); 4,000 lbs. (A/E32K—9 MAC II)
4,000 lbs.(A/E32K—3, MAC); 6,000 lbs. (A/E32K—9 MAC II)
6,000 lbs.(A/E32K—3, MAC); 6,000 lbs. (A/E32K—9 MAC II)
6,000 lbs.(A/E32K—3, MAC); 10,000 lbs. (A/E32K—9 MAC II)
How many rail conveyors does the munitions assembly conveyor consist of?
Four
Five
Six
Seven
Which technical order (TO) covers the rapid-assembly and inspection procedures of nonnuclear munitions?
11A-1-42
11A-1-46
11A-1-60
11A-1-63
What is the minimum number of feet required to assemble the A/E32K—3, munitions assembly conveyor?
50 x 100
100 x 200
150 x 200
200 x 500
Why is it important to monitor net explosive weight (NEW) during a bomb buildup operation?
Excessive NEW at your location usually means a shortage at other sites
Excessive NEW at your location will limit the operating space needed for bomb building
If ignited, excessive NEW may cause the intermagazine and intraline distances to increase
If ignited, excessive NEW may cause propagation of an explosive from one location to another
When packing up the munitions assembly conveyor (MAC) it is important to cap the ends of the air hoses to keep
corrosion from setting in.
pressurized air from escaping.
the hose ends from being crushed.
foreign materials from damaging them.
What does Title 49 of the code of federal regulations (CFR) regulate?
Contingency operations
Special access required for classified cargo
Shipments of hazardous material, including explosives within the United States
All shipments of explosives and munitions within the United States and overseas
Which approved restraining devices can be used for securing munitions on United States Air Force (USAF) vehicles/trailers?
Steel banding and steel chains
Tie-down straps and bungee cords
Chains/binders, cargo nets, and tie-down straps
Chains/ratchets, heavy tarps, and tie-down straps
When is it permissible to transport explosives in privately owned vehicles (POV)?
Never
During contingency operations only
When given approval from the squadron commander
Only for movements beginning and ending within the munitions storage area
What is the primary focus when designating primary and alternate explosive movement routes?
Use the most covert possible routes
Use the securest possible routes
Use the fastest possible routes
Use the safest possible routes
What source is best used to determine the explosive hazard class/division of a specific munitions item?
Technical Order (TO) 11A-1-46
Technical Order (TO) 11A-1-63
Defense Explosives Safety Regulation (DESR) 6055.09_Air Force Manual (AFMAN) 91–201
Joint Hazard Classification System (JHCS)
What should you do if a conflict is discovered while using Technical Order (TO) 11-1-38 between the illustrations and the written procedures?
Follow the illustrations
Follow the written procedures
Make a command decision and chose one
Put the operation on hold until a TO change is recieved
Even though TO 11–1–38 has it own safety section, what other publication should you reference for safely transporting explosive items on base?
TO 11A—1—1
TO 11A—1—10
TO 11A—1—63
Defense Explosives Safety Regulation (DESR) 6055.09_Air Force Manual (AFMAN) 91—201
What type of information is given in the general notes on the first card of each trailer and weapon-type section in Technical Order (TO) 11—1—38 and is required to be reviewed?
Illustrations for each trailer configuration
Equipment and quantity required for each trailer
Equipment and quantity required for each trailer and weapon
WARNINGS, CAUTIONS, and NOTES pertaining to each trailer and weapon
If you cannot fully close the load-binder handle by hand,
use a forklift to close the handle.
use a cheater bar to close the handle.
adjust the load-binder hooks on the chain.
replace the load binder with a newer one that’s not rusted.
Which type of munitions do the MHU—141 munitions trailers configured with M9 or M10 adapters transport?
Air-to-air munitions
Air-to-ground munitions
20 mm ammunition
30 mm ammunition
When configuring the MHU—141 trailer, when are the support beams placed in the out position?
Deck is opened
Deck is closed
Pintle hook is opened
Pintle hook is closed
Upon load completion, which of the following steps are to be accomplished?
Traverse munitions over previously loaded munitions
Ensure several tripping hazards exist with loose quick-release pins and chocks
Ensure trailer is placarded for the hazard involved
Place weapon on the rail extender
It is a requirement to damage explosives or containers to ensure munitions are secured to the trailer.
True
False
How many different rail configurations can the aluminum rail set be assembled in the trailer deck?
Three
Four
Five
Six
The rails configured in the longitudinal direction run perpendicular with the trailer deck and are placed approximately in the front, center, and rear of the trailer.
True
False
During the loading operation, which of the following steps are not to be accomplished?
Front of the trailers will be loaded first and unloaded last
Ensure rail extenders are properly installed and secured with quick-release pins
Do not allow weapons to roll down the aluminum rail set assembly unattended or unsecured
Side load binder handles will be secured on the passenger side of the vehicle
Before loading, unloading, or unpinning the trolley assemblies, what needs to happen to the trolley stop plunger?
Nothing
Ensure it is removed from the assembly
Ensure it is engaged in the appropriate hole
Ensure it is in the disengaged position
For the latitudinal configuration, where are the rail assemblies positioned on the deck trailer?
Parallel to the trailer deck
Clockwise to the trailer deck
Diagonal to the trailer deck
Perpendicular to the trailer deck
It is a requirement to ensure rail extenders are properly installed and secured with quick-release pins prior to use.
True
False
What piece of equipment must be used with the MHU—110 to prevent the trailer from becoming unstable while using the rail extenders for loading and unloading heavy munitions?
Longitudinal trolley
Cradle assembly
Stabilizer jack
M10 adapter
What can be constructed and attached to the bed of a 40—foot trailer to facilitate support of rounded munitions?
Universal chock assembly
Wooden rail sets
Iron rail sets
Bomb rack
What provides an itemized list of all equipment authorized for use with nuclear weapons?
Master nuclear certification list
Unit committed munitions list
Technical Order (TO) 11A—1—63
Technical Order (TO) 11—1—38
Once verified that an item is nuclear certified, how is it identified as such?
Positive identification by a stamp, stencil, or etching
Item will be stamped “NUCLEAR CERTIFIED” in black ink
Item will be stenciled “NUCLEAR CERTIFIED” in black paint
Positive identification by a nameplate, label, appropriate markings, or by official documents
Which statement about pintle hooks and their use in operations with nuclear weapons is correct?
Original equipment pintle hook assemblies are authorized
Front mounted pintle hooks are only authorized for towing on the flight line
Off-center rear of vehicle pintle hooks can be used as long as both sides are used
Replacement pintle hooks can be procured and installed per local operating instructions
Which items do not require nuclear safety certification for use in operations with nuclear weapons?
Combat delivery vehicles
General-purpose hand tools
Noncombat delivery vehicles
Equipment used to transport nuclear weapons
When should you replace a nuclear certified MB—1 tie-down/chain assembly item?
Every 10 years
Every 25 years
Only when the item no longer functions
After finding any cracks, bent/worn parts, or excessive corrosion
Which action is not an authorized method for securing loose lengths of chain when using the MB—1 tie-down device/chain assembly?
Loop the excess chain around the chain itself; secure with durable adhesive tape
Loop the excess chain around the chain itself; secure with an electrical bundle tie
Wrap the loose ends around the tie-down device and secure to the quick-release lever
Wrap the loose ends around a container tie-down point; secure with an electrical bundle tie
When using a load binder for securing a load, what is the main reason for not using a cheater bar or extension tool to fully close the handle?
It would place too much pressure on the load and/or tie-down points
Fingers could get pinched between the tool and the load binder
There is no written guidance for this procedure
Not an authorized tool
Which device is commonly referred to as a tie-down strap?
GFU—7/E
CGU—1/B
MB—1
GFU—8/E
What are the key factors to consider during a nuclear weapons movement?
Time and money
Safety and security
People and equipment
People and the mode of transportation
Which area is designated as a location used temporarily during a delay of an off-base movement involving nuclear weapons?
No-lone zone
High security
Close-in security
National defense
What code word is used when a Department of Energy (DOE) convoy seeks sanctuary during an emergency?
Bent spear
Safe haven
Empty quiver
Covered wagon
In Regards to ground transportation, when are nuclear weapons moved by convoy?
When on base or within the confines of a military installation only
When off base and traveling over state highways only
Only when more than one weapon is being moved
Every time weapons are moved
What is the most difficult job for escort guards during a convoy?
Keeping other vehicles from entering the convoy
Maintaining the proper speed required in a convoy
Keeping the proper distance from the security forces
Identifying the correct checkpoints along the convoy route
