WorksheetsMTL2 Site Prep Mock Test
Total questions: 59
Worksheet time: 30mins
Which type of screwdriver would you use?
Philips screwdriver
Pozidrive Screwdriver
Star Head
Flat blade
Which type of screwdriver would you use?
Philips screwdriver
Pozidrive Screwdriver
Star Head
Flat blade
Name the Hand tool?
Combination Pliers
Circlip Pliers
Long nose Pliers
Water Pump Pliers
Name the Tool?
Junior Hack Saw
Floor board Saw
Hack Saw
General-purpose Hand Saw
Why would you over bend a 90 degree angle using a bending spring
To be able to withdraw the spring from the copper easier
flow rate
pressure
looks better
Where would you use this Power too?
Cutting floorboard
Cutting plaster board
Cutting brick work
Cutting corners
Name the Power tools?
Reciprocating saw
Circular saw
Jig saw
Multi tool
What is show in the image?
Hole Saw
Core Bit
Metal Drill Bit
Masonry Bit
This is the most widely used grade of copper tube for plumbing and heating applications?
R250
R300
R290
R220
What type of fitting is shown?
Wood Drill Bits
Metal Drill Bits
Spade Bits
Masonry Drill Bits
What type of fitting is shown?
Push Fit
Compression
End Feed
Press Fit
What fitting is shown?
U-Bend
Goose Neck Connector
Flexible Connector
Tank connector
What is shown in the picture?
Flange
Pipe Insert
Tube fitting
Pop-it Fitting
The installation process is usually in two stages they are known as?
Primary and Secondary
A fix and B fix
Job 1 and job
1st Fix and 2nd Fix
Which of the following statements is incorrect?
equipment and materials left lying about can cause people to trip, slip or fall.
after work activity tools and equipment should be cleared away and correctly stored.
Store materials where they are inaccessible to your co-workers
nsure hazardous substances are stored as per the manufacturers' directions or COSHH regulations.
When using an electric pipe freezer what is the maximum duration you can work on the pipe?
15 minutes
45 minutes
50 minutes
60 minutes +
When Chasing a wall the vertical chase thickness must not be deeper than ___ of the wall thickness.
3/4
2/3
1/3
1/4
When Chasing a wall the horizontal chase thickness must not be deeper than ___ of the wall thickness.
3/4
1/6
1/3
1/4
What fitting is shown?
Reducer Tee
Compression offset
Lead Lock
Isolating Valve
What is shown in the image?
Pressure Cup
Weir/flow Cup
Haymarket measuring Cup
Pressure Guage
What is shown in the image?
Percussion Drill
Hammer Drill
Wet Drill
Core Drill
To avoid damage to a customer's property when removing an old galvanised cold water cistern from the roof space a plumber should.
Wrap the edges of the cistern with foam in case it catches the paint work or furniture
Seal all of the outlets to prevent discoloured water running out onto the floor coverings
Leave the cistern in the roof space, making sure that it is placed on a sturdy timber base
Ask the customer to arrange for a professional removal company to dispose of the cistern
Which one of the following items should be left with the customer following the installation of a new boiler?
Boiler Installation Template
All material delivery notes
DIY servicing information
Benchmark Book
Which one of the following parts of the Building Regulations deals with building structure?
Part A
Part B
Part F
Part L
Which one of the following should be used to protect the area you are working in?
Safety shoes
Plywood
Dust sheets
Heat mat
Which one of the following is the correct horizontal clipping interval for 15mm copper tube?
1.2 metres
1.5 metres
1.8 metres
2.0 metres
Which one of the following is the correct horizontal clipping interval for 15mm copper tube?
1.2 metres
1.5 metres
1.8 metres
2.0 metres
According to Building Regulations Part A, what is the maximum depth a joist can be notched to?
1/4
1/6
1/8
2/8
What is this called?
Saddle Clip
Nail-on Clip
School Board Pipe Clip
Munsen ring clip
What is the standard associated with Copper Tube?
BS EN 1098
BS EN 1172
BS EN 6440
BS EN 1057
This grade is hard tempered, thin walled and totally unsuitable for bending.
R220
R250
R290
R300
Which type of plastic pressure pipe is commonly used for mains cold water and is colored blue?
Polybutylene
High Density Polyethylene (HDPE)
PVCu
Medium Density Polyethylene (MDPE)
What type of fitting is this?
Philmac
Leadlock
Compression
Push fit
What type of Valves are these?
Stop tap
Gate valves
Service valves
What type of fittings are these?
Tank Connectors
Reducers
Tap Connectors
Manifold
Lubricant should be used on what fittings
Compression
Press fit
Push fit Soil/waste pipe and fittings
Solvent soil/waste Pipe and Fittings
What document should you always refer to when installing/servicing a product?
Industry Standards
Manufacture Instruction
Customers Home Guide
Building Regulations
What should a plumber do before removing carpets or furniture from the work area?
Remove them without informing the customer
Leave them in place and work around them
Replace them with new ones after the job
Ask the customer to remove them or get permission to do so
What should a plumber do if a customer’s car is parked near the work area where brick dust or debris may fall?
Ignore it and begin work
Cover the car with a dust sheet
Ask the customer to move the car
Wash the car after the job is complete
How should a plumber protect customer property when using soldering equipment?
Use a fan to blow the heat away from surfaces
Use a heat mat or flame-retarding gel
Point the blow torch away from the customer’s property
Only solder outside the property
What must be done when replacing lifted chipboard flooring?
Paint the edges to seal them
Support the edges with wooden noggins
Add insulation underneath
Glue the boards to the wall
What is the maximum depth allowed for a notch in a joist that is 200mm deep?
25mm
37.5mm
75mm
12.5mm
What is the clipping distance for 15mm copper pipe
1.2m Horizontal
1.8m Vertical
1.8m Horizontal
2.4m Vertical
1.2m Horizontal
2.4m Vertical
0.8m Horizontal
1.2m Vertical
What is the clipping distance for 22mm copper pipe?
1.2m Horizontal
1.8m Vertical
1.2m Horizontal
2.4m Vertical
1.8m Horizontal
2.4m Vertical
0.8m Horizontal
1.2m Vertical
Name the Type of Screw?
Cross Head/Pozi Drive Screw
Round Head Screw
Chip Board Screw.
Mirror Screw
Name the Plater board fixing?
Collapsing cavity fixings
Spring loaded toggle bolts
Self-drill plaster board fixings
What is this?
intumescent collar
Pipe cover
Weather color
Cap end
If you drill through a wall to install pipe work, what must you use to protect the pipe work?
Sleeving
Tape
insulation
nothing
If your working in a customer property and you work like to leave your tools over night what must you do?
have permission off your supervisor
Ring your parents
Have customers permission
make sure the door is locked
What pressure do you test copper pipe work at?
1 x working pressure
1.5 x working pressure
2 x working pressure
2.5 x working pressure
What happens to the length of copper when you bend it?
increases in length
decreases in lenghth
What is the ratio fall that guttering bracket should be installed to?
1:600
2:600
3:600
4:600
What the maximum distance allow between gutter brackets
1000mm
1200mm
1300mm
1400mm
What is the most common pipe work that you can bend using a scissor bender?
R220
R250
R290
R2D2
What oil is used with LCS?
Threading oil
Cooking oil
Olive Oil
Motor Oil
What is this Kite mark
Heart foundation
Scottish
British
Building
What should all fittings be?
Cheap
WRAS approved
Secondhand
What must be used while connecting MDPE pipe to an MDPE fitting?
Plastic Insert
PTFE
Olive
Name the fitting?
Coach bolt
Expander
Cavity Fixing
