WorksheetsSAE Connection Proper Tool Selection and Use
Total questions: 94
Worksheet time: 47mins
What is the principal action of most cutting tools?
To guide a serrated or sharpened blade through a material to cut it to the desired dimensions
To hammer nails into wood
To measure the length of materials
To glue materials together
What is the most basic of cutting tools?
The knife
The saw
The chisel
The file
What is the business end of any saw?
Its teeth
Its handle
Its back edge
Its blade guard
How are saw teeth sized and shaped?
According to the color of the saw
According to the type of material the saw is intended to cut
According to the length of the handle
According to the price of the saw
What is the main difference between crosscut saws and ripsaws?
Crosscut saws have pointed knifelike teeth for cutting across the grain, while ripsaws have chisel-shaped teeth for cutting parallel to the grain
Crosscut saws are only used for metal
Ripsaws are used for painting
There is no difference
What is a hacksaw primarily used for?
Cutting metal
Cutting fabric
Cutting glass
Cutting food
Coping saws are best suited for:
Cutting straight lines in metal
Cutting shapes in sheet materials
Cutting food
Cutting glass
The teeth of a hacksaw blade are usually set in a ___ pattern to widen the kerf.
wavy
straight
zigzag
spiral
Keyhole saws are often used to:
Cut metal pipes
Cut through interior wall panels to install electric switches and power outlets
Cut food
Cut glass
Hacksaws should be assembled and used with the teeth angled forward to cut on the push stroke.
True
False
A coping saw has a ___-shaped metal frame.
U
L
O
S
When using a keyhole saw to cut into an existing wall, what should you be careful not to accidentally cut into?
Electrical or plumbing systems
Wallpaper or paint
Insulation only
Drywall screws
What is a backsaw primarily used for?
Cutting curves in wood
Cutting very straight lines
Drilling holes
Sanding surfaces
Backsaws are mostly used in trim work and in the construction of _____
fine furniture
bridges
roads
boats
What feature on the backsaw keeps it straight while cutting?
The handle
The stiffening rib
The teeth
The miter box
When using a backsaw, should you apply pressure on the backstroke?
True
False
Hand-powered drills use sharpened bits to bore holes in all types of construction material.
True
False
What are the two common types of bits used in hand-powered drills?
Auger bits and twist drill bits
Forstner bits and spade bits
Hole saws and masonry bits
Countersink bits and brad point bits
Twist drill bits have a _____ shank, while auger bits commonly have a tapered, square shank.
round
hexagonal
triangular
flat
Why are hand-powered drills still useful despite the development of cordless electric drills?
They are better for drilling deep, large bore holes in large lumber and posts, can be carefully controlled when precise bore depth is needed, and do not need electricity, which is ideal in remote locations.
They are more expensive and require frequent maintenance compared to electric drills.
They are only used for decorative purposes in modern woodworking.
They are faster and more powerful than any electric drill available.
Fill in the blank: You should mark hole locations with a ______ before drilling.
center punch
hammer
screwdriver
tape measure
Which of the following is NOT a recommended safety tip when drilling?
Clamp or secure material so it will not move
Use dull bits for faster drilling
Apply enough pressure to keep the bit engaged
Use a backing board to prevent splintering
Fill in the blank: A brace and bit is a valuable tool to have in your toolbox when building ______ fences and buildings.
agricultural
electric
plastic
stone
Which of the following is NOT a type of hand-powered drill mentioned in the text?
Hand drill
Pin vise
Cordless drill
Push drill
Fill in the blank: A pin vise is used by machinists and others who need to drill very small ______ for screws.
holes
wires
bolts
threads
What is the main purpose of taps and dies?
To cut wood
To measure thread size
To create threaded connections
To drill large holes
When using taps or dies, what should you always use with the tap or die?
The proper handle
A hammer
A screwdriver
A wrench
When using taps or dies, how should you keep taps and dies sharp?
By properly cleaning and storing them in a secure compartment away from other tools.
By using them on harder materials frequently.
By soaking them in oil overnight after every use.
By sharpening them with a file after each use.
When cutting threads in metal, what should you use as a lubricant?
Cutting oil
Water
Vegetable oil
Grease
What motion should you use to clear the cutting surfaces of metal chips while cutting threads with taps or dies?
Two steps forward, one step back motion
Continuous forward motion
Rapid back-and-forth motion
Circular motion
What should you use to clean up waste chips when using taps or dies?
A soft brush
A cloth rag
Compressed air
Your bare hands
You should wipe away metal chips with your bare hands when using taps or dies.
True
False
What type of hammer should you use when using a cold chisel?
A hammer that is engineered for striking other tools
A claw hammer
A rubber mallet
A wooden mallet
What is a chisel?
A cutting tool that uses a sharpened inclined plane to remove small pieces of material from a larger stock.
A measuring instrument used to determine the length of an object.
A device used to fasten two materials together using screws.
A tool used to mix paint and other liquids.
How are planes powered?
By the user's strength alone
By solar panels only
By wind-up mechanisms
By engines (jet or propeller)
Why is the term 'cold' used for cold chisels?
Because the metal is worked during manufacturing without being heated.
Because the chisel is always kept in cold storage.
Because it is used only in cold weather.
Because it is made from a special cold-resistant alloy.
Hand planes are used for:
Cutting metal
Shaving thin layers from the surface of wood
Removing nails
Mixing paint
Files and rasps are made from:
Plastic
Hardened tool steel
Aluminum
Copper
On a single cut file, the teeth all go in ______ direction.
one
two
opposite
random
Rasps have rows of multiple triangular teeth that remove material more aggressively than files.
True
False
What is the purpose of the tang on a file or rasp?
It is intended to be inserted into a handle.
It is used for measuring angles.
It is designed for sharpening blades.
It is meant to provide extra weight.
What type of brush is recommended to clean the file as needed?
A short, stiff-bristled brush called a file card.
A soft paintbrush.
A wire wool pad.
A toothbrush.
Why should nonmetallic bristles be used instead of steel bristles to clean a file?
Steel bristles can dull the file.
Nonmetallic bristles are easier to find.
Steel bristles are more expensive.
Nonmetallic bristles clean faster.
What is mushrooming in the context of tool use, and how can it be prevented?
Mushrooming is the dangerous flattening and distortion of the head of tools that are repeatedly struck with a hammer. It can be prevented by using the correct type of hammer and keeping chisel and punch heads correctly ground.
Mushrooming is the process of cleaning tools with a special solution. It can be prevented by storing tools in a dry place.
Mushrooming refers to the rusting of metal tools over time. It can be prevented by applying oil regularly.
Mushrooming is the bending of tool handles due to excessive force. It can be prevented by using handles made of metal.
What is the main advantage of using power tools over hand planes for most jobs?
Power tools have replaced hand planes for most jobs, but hand planes are still effective for shaving the edge off a door sticking in its frame or for straightening a twist warp from a board.
Power tools are less accurate than hand planes for detailed work.
Hand planes are faster than power tools for large jobs.
Power tools are only used for decorative purposes.
What is the purpose of using soapstone with a file?
Soapstone helps to prevent small chips of filed metal from clogging up the file and serves as a dry lubricant.
Soapstone increases the hardness of the file for tougher materials.
Soapstone is used to sharpen the file's teeth.
Soapstone is used to color-code files for different materials.
What is the key to using any gripping tool effectively?
Maximizing grip surface area is the key to using any gripping tool.
Applying minimal force is the key to using any gripping tool.
Using the tool at a high speed is the key to using any gripping tool.
Ignoring the tool's design is the key to using any gripping tool.
What are the two jaws of a vise called?
One stationary and one movable jaw.
Both are stationary jaws.
Both are movable jaws.
One upper and one lower jaw.
What is the main difference between a mechanic's vise and a machinist's vise?
The machinist's vise is commonly constructed under stricter tolerances with higher quality materials and usually has steel jaws that can be covered or replaced with softer materials for holding more delicate parts.
A mechanic's vise is always smaller and lighter than a machinist's vise.
A machinist's vise is only used for woodworking, while a mechanic's vise is used for metalworking.
A mechanic's vise has built-in measuring tools, while a machinist's vise does not.
What is a common feature of mechanic's vises?
They have a large anvil surface
They are constructed to swivel on a base plate mounted to the top of the workbench
They are made entirely of wood
They are only used for woodworking
Fill in the blank: Mechanic's vises are constructed a bit more ______ than machinist's vises, but both have jaws that remain parallel and are capable of exerting tremendous clamping force.
coarsely
precisely
lightly
delicately
Which of the following is true about woodworking bench vises?
They are always mounted on top of the bench
They have soft wooden inserts to reduce damage to lumber
They are used for holding pipes
They do not have a retractable block
Pipe vises are primarily used by which professionals?
Carpenters
Plumbers
Electricians
Mechanics
Fill in the blank: Yoke-type pipe vises come in a variety of sizes to accept different sizes of ______.
pipes
wires
bolts
cables
What is one maintenance tip for keeping vises in good working condition?
Never lubricate the moving parts
Use excessive lubricant
Keep the jaws in good condition to allow vises to grip snugly without causing excessive damage to parts
Only clean the vise once a year
What is the main function of clamps as described in the passage?
Clamps are used to hold parts and materials together and stationary while work is performed.
Clamps are used to measure the length of materials.
Clamps are used to paint surfaces evenly.
Clamps are used to heat materials during processing.
According to the passage, the more sturdily a clamp is constructed, the more ______ it can apply.
force
color
noise
heat
What enables the C-clamp to grip material very securely?
The leverage of the sliding handle combined with the long screw enables the C-clamp to grip material very securely.
The rubber padding on the jaws provides extra grip.
The magnetic base holds the material in place.
The spring mechanism inside the clamp increases pressure.
Which of the following is NOT a feature of C-clamps?
C-shaped metal frame
Threaded rod with a handle
Wooden jaws
Swiveling pad on the clamping end
Parallel clamps are often the best choice for holding lumber together for woodworking projects.
True
False
Why can't parallel clamps be used for hot metalworking?
Because the clamp face is wood, it cannot be used for hot metalworking.
Because parallel clamps are too small for hot metalworking.
Because parallel clamps are made of plastic.
Because parallel clamps cannot hold metal securely.
Bar clamps use ______ jaws to clamp across an extended distance.
parallel
curved
serrated
angled
What is the main function of spring clamps?
To apply a strong clamping force
To temporarily hold small parts in place using stored energy from a spring
To weld metal parts together
To cut materials
Spring clamps do not apply a strong clamping force relative to other types of clamps.
True
False
Magnetic clamps are used to hold _______ ferrous parts in place.
smoothsurfaced
rough-edged
painted
non-metallic
Which of the following is a safety concern when using magnetic clamps?
They can be exposed to extreme heat
They should not be exposed to extreme heat
They are not strong enough to hold metal parts
They cannot be switched off
A switch or lever on the surface of a magnetic clamp aligns the magnetic poles of the interior magnets for clamping.
True
False
What is the primary function of pliers?
To grip, turn, twist, hold, or cut objects
To measure objects
To weld metal
To paint surfaces
Fill in the blank: The jaws of most pliers are much ______ than the handles to provide a mechanical advantage in gripping objects.
shorter
longer
thicker
heavier
Which type of pliers has an elongated, figure-eight-shaped hole at the fulcrum that allows the jaws to be shifted to two positions?
A) Lineman's Pliers
B) Slip-Joint Pliers
C) Groove-Joint Pliers
D) Needle-Nose Pliers
Lineman's pliers are especially useful for work on which type of material?
Wood
Thin sheet metal
Plastic
Glass
Groove-joint pliers are also known as:
Combination pliers
Tongue-and-groove pliers
Side-cutting pliers
Needle-nose pliers
Fill in the blank: Needle-nose pliers have long, narrow, tapering jaws capable of reaching deep into ______ places.
tight
cold
wet
bright
Needle-nose pliers may be used for gripping very small parts or for twisting wires into small loops.
True
False
What is the main purpose of cutting pliers?
To strike objects
To cut through material
To clamp objects
To measure objects
Cutting pliers may be designed to cut in several different ways. Name one way mentioned in the passage.
Two wedge-shaped blades may come together to pinch through material, a single blade may pinch through material as it approaches a backing plate or anvil, or blades may bypass each other in a scissor-like action.
Cutting pliers may be designed to heat material before cutting.
Cutting pliers may be designed to glue materials together.
Cutting pliers may be designed to bend material without cutting.
Diagonal pliers are designed to cut light-gauge wire and have two cutting edges that pinch together to cut the wire.
True
False
Which of the following is NOT a type of cutting pliers?
Bolt cutters
Cable cutters
Tin snips
Vise-Grip pliers
Who was granted the patent for the first set of locking pliers?
John Smith
Bill Petersen
Thomas Edison
George Westinghouse
Locking pliers offer strong clamping strength combined with a ______ and quick release feature.
jaw adjustment screw
magnetic tip
insulated handle
ratcheting mechanism
What is the most common striking tool mentioned in the passage?
Screwdriver
Hammer
Wrench
Pliers
The weight of a hammer refers to the ______ weight and excludes the handle weight.
head
total
shaft
grip
What is the most common type of hammer used for driving nails?
Ball-peen hammer
Claw hammer
Sledgehammer
Mallet
Claw hammers are usually on the heavier side and are built to withstand harsh use.
True
False
Fill in the blank: The edges of the face of a claw hammer are _______ to prevent chipping.
beveled
rounded
sharpened
painted
Which type of hammer is used for shaping metal and driving punches and chisels?
Claw hammer
Ball-peen hammer
Sledgehammer
Framing hammer
The handle of a hammer is made to form a natural grip at the base. Gripping in the correct position increases power and accuracy.
True
False
What is the process of repeatedly hammering a metal surface to improve surface characteristics called?
Peening
Annealing
Quenching
Tempering
Sledge hammers are used for which of the following tasks?
Repairing auto bodies
Driving posts and breaking concrete
Leatherworking
Forming mallet heads
Fill in the blank: The head of a sledge hammer is usually ______ with two identical, opposing flat faces.
octagonal
cylindrical
triangular
hexagonal
Soft-faced hammers are designed to shift parts into position without causing material damage or producing ______.
sparks
noise
heat
vibration
Dead-blow hammers are designed to deliver a single blow while minimizing the rebound of the hammer head.
True
False
What material is commonly used to fill the heads of dead-blow hammers?
Water
Sand or steel shot
Rubber
Brass
What is the primary use of an anvil?
To cut metal
To back up or support the work when shaping metal parts
To measure metal
To polish metal
