NEW
Font size
WorksheetsBuilding Tech 3 Final Quiz Part 2
Total questions: 17
Worksheet time: 1hrs 25mins
A construction crew installs temporary molds to shape freshly poured concrete walls and removes them after curing. What system is being used?
Concrete surfacing
Concrete formwork
Masonry veneer
Wall flashing
A residential project uses wall cavities to run electrical wiring and install insulation. Which wall system allows this arrangement?
Masonry bearing walls
Concrete shear walls
Stud wall system
Precast concrete panels
An engineer specifies masonry walls reinforced with steel bars and grout to resist seismic and wind forces. What wall system is this?
Unreinforced masonry
Veneer masonry
Reinforced masonry
Load-bearing stud wall
If a commercial building with a flat roof is located in a region with frequent heavy rainfall, what additional design consideration should be made to prevent water accumulation and leaks?
Use clay tiles for roofing
Increase roof slope and specify continuous membrane roofing
Install timber planks for drainage
Add ceiling finish for water resistance
For a warehouse requiring rapid construction and minimal on-site labor, which wall panel method offers the most strategic advantage?
Tilt-up construction
Precast concrete construction
Platform framing
Reinforced masonry
For a commercial building with slow roof drainage, what is the reasoning behind specifying continuous membrane roofing over other options?
It is more decorative
It provides seamless waterproofing and prevents leaks
It is less expensive than clay tiles
It is easier to install than timber planks
When selecting a wall system for a high-rise building in a windy region, which system should be chosen to ensure structural integrity and why?
Unreinforced masonry
Veneer masonry
Reinforced masonry,
Load-bearing stud wall
In a project where concrete wall panels are cast and lifted into place on site, what strategic planning consideration must be made regarding site logistics?
Ensure adequate space for cranes and panel storage
Use only manual labor for lifting panels
Cast panels vertically for easier installation
Avoid scheduling during rainy weather
If a building consistently experiences leaks at roof edges after rain, what evidence-based reasoning supports the need for proper flashing installation?
Flashing prevents water infiltration at vulnerable joints
Ceiling finish absorbs excess water
Roof insulation keeps the roof dry
Timber planks direct water away from edges
A sloping roof uses rafters, purlins, and decking to support the roofing material. Which description best fits this roof structure?
Nonstructural roof assembly
Typical sloping roof structure
Flat roof system
Curtain wall roof system
Precast concrete roof slabs are installed and topped with reinforced concrete to act as one structural unit. What is the main purpose of the topping?
Improve surface finish only
Add thermal insulation
Provide structural continuity
Reduce roof slope
A flat roof framed with steel beams and decking is designed similarly to a floor system. This roof structure is most comparable to:
Timber truss roofing
Masonry bearing construction
Steel floor framing
Cementitious plank roofing
A roof design includes gutters, downspouts, and scuppers to safely direct rainwater away from the structure. What system is being addressed?
Roof insulation system
Roof drainage system
Roof framing system
Roof finishing system
Bearing connections for precast roof slabs are detailed to allow slight horizontal movement. What problem does this prevent?
Roof uplift during typhoons
Cracking due to creep, shrinkage, and temperature changes
Excessive roof deflection
Poor roof drainage
When designing a roof system to resist uplift forces during a typhoon, which connection detail is most critical?
Roof-to-wall anchorage
Gutter installation
Roof insulation
Downspout sizing
For a roof drainage system, what is the strategic reason for including overflow scuppers in the design?
To improve insulation
To prevent water accumulation and roof collapse
To enhance visual appearance
To reduce construction time
A designer chooses a roofing system composed of multiple layers of bitumen and felt for a low-slope roof requiring durability. Which system is this?
Single-ply roofing
Built-up roofing (BUR)
Vegetated roofing
Sheet metal roofing
