Worksheets105 Revision
Total questions: 25
Worksheet time: 13mins
What can be used to protect the eyes?
Safety goggles
Ear defenders
Hi-visibility vest
Hard hat
What does a red sign indicate?
Prohibition or stop
Mandatory instruction
Safe condition or first aid
Caution or warning
What action should be taken if an alarm sounds?
Evacuate immediately to the assembly point
Keep working until a supervisor arrives
Call a colleague to check
Silence the alarm and continue
What should you do with leftover cables and fittings?
Coil and store neatly in a labeled container
Leave them on the floor until the end of the day
Throw them into general waste without sorting
Hide them behind equipment
Which practice focuses on verifying measurement accuracy?
Meter calibration
Visual safety checks before use
PAT testing
Lightly oiled
Which practices can help maintain tools in good working condition?
Clean and dry tools after use to prevent corrosion
Apply light oil to moving parts such as pivots and hinges
Inspect insulated handles and casings; replace the tool if damaged
Use each tool only as designed and store it safely in a case or rack
Leave tools wet or unprotected in a damp toolbox to save time
Which tool maintenance step should be performed before operating a tool?
Visual safety checks before use
PAT testing
Meter calibration
Lightly oiled
Which tool is specified to tighten terminals?
Terminal screwdriver
Pozi drive/Phillips screwdriver
Pliers
Hammer
Which tool is used to insert cross head screws?
Pozi drive/Phillips screwdriver
Terminal screwdriver
Pliers
Tape measure
Which device self-destructs when the current surpasses a preset value in the circuit?
MCB
Fuse
According to the table, which device is defined as a circuit protection device that trips when there is excess current flow?
MCB
Fuse
Which device is usually reusable?
MCB
Fuse
Name the fastener shown in the image.
Dome head slotted screw
Counter sunk screw
Plasterboard fixings
Gutter bolts/Roofing bolts
Name the fastener shown in the image
Dome head slotted screw
Counter sunk screw
Plasterboard fixings
Board screw
Name the fixing shown in the image
Dome head slotted screw
Counter sunk screw
Plasterboard fixings
Gutter bolts/Roofing bolts
Identify the item shown
M4 Brass pan head
M3.5 Face plate screws
Wall bolts
Cable clips
Wall plugs
Identify the item shown
M4 Brass pan head
M3.5 Face plate screws
Wall bolts
Cable clips
Wall plugs
Identify the fitting shown
Coupler
Metal saddles
Plastic saddles
Male brass bush
PVC female adapter
Identify the fitting shown
Coupler
Metal saddles
Plastic saddles
PVC female adapter
Identify the fitting shown
Metal saddles
Plastic saddles
Male brass bush
PVC female adapter
Identify the fitting shown in the bottom-right image of the page.
Coupler
Metal saddles
Plastic saddles
Male brass bush
PVC female adapter
Identify the accessory shown in the image of a white wall plate with two 13A socket outlets and two rocker switches.
Two gang 13A switched socket outlet
One gang 13A switched socket outlet
One gang 13A Unswitched socket outlet
Fuse connection unit 13A Switched fused spur (with flex outlet) Without Neon
Identify the accessory shown in the image of a white wall plate with a single 13A socket outlet and one rocker switch.
Two gang 13A switched socket outlet
One gang 13A switched socket outlet
One gang 13A Unswitched socket outlet
Fuse connection unit 13A Switched fused spur (with flex outlet) Without Neon
Identify the accessory shown in the image.
Two gang 13A switched socket outlet
One gang 13A switched socket outlet
One gang 13A Unswitched socket outlet
Fuse connection unit 13A Switched fused spur (with flex outlet) Without Neon
Identify the accessory shown in the image.
Two gang 13A switched socket outlet
One gang 13A switched socket outlet
One gang 13A Unswitched socket outlet
Fuse connection unit 13A Switched fused spur (with flex outlet) Without Neon
