Mini Quiz

Multiple Choice

When all the letters of the alphabet ……………… up for the first letter (identifier), the sequence starts again with letter A.

• has been used

• a)   has use

• a)  have used

• have been used

Multiple Choice

A WARNING tells the operator that injury or death is possible, if the operator ………… obey the specified instruction.

• does

• does not

• would

• would not

Multiple Choice

If a broken fastener ………………., replace it by a new one of the

same part number.

• is detected

• detects

• is detecting

• has detected

Multiple Choice

Additional maintenance task …… ……………….. depending on the failure modes intended to be covered under this entry.

• might require

• may require

• may be required

• was required

Multiple Choice

If the test ……… the maintenance message recirculation valve RH(212HG), replace the recirculation valve.

• give

• gives

• gave

• given

Multiple Choice

The fan …………… 6 seconds after approximately, then the warning light goes off.

• will operate

• has operated

• operate

• can operate

Multiple Choice

Major sub-zones are identified by the ten of the majors zones.

 

What does “identify” mean?

• To question something's identity

• To confuse something's identity

• To recognize something’s identity

• To change something's identity

Multiple Choice

Park the aircraft on a flat surface.

 

What is a synonym for “flat”?

• Smooth

• Curved

•  Rough

• Bumpy

Multiple Choice

You must obey the applicable safety precautions ………………… serious injury or death in a wheel explosion

•  to celebrate

• to prevent

• to cause

• to persist

Multiple Choice

Install battery terminal protectors ………… the battery is not connected in the aircraft or to the test equipment.

• whenever

• wherever

• whichever

• whoever

Multiple Choice

Each chapter/system is further divided …… sections/subsystems.

• above

• into

• on

• under

Multiple Choice

These precautions will ………….. the risk of contamination and damage to the electrical wiring installation.

• incline

• decline

• increase

• decrease

Multiple Choice

All calendar days are considered to run consecutively.

 

What is the meaning of the word "consecutively"?

• simultaneously

• in a random order

• one after another

• spontaneously

Multiple Choice

If there is a short circuit, you will cause damage to the serviceable computer when you swap or replace them.Which verb can be used instead of "swap"?

• displace

• purchase

• repair

• use

Multiple Choice

The drag is normally approx. to 40 lbf.in. It can be less, but the permitted maximum is to 107 lbf.in.

 

What does “permitted” mean?

• forbidden

• allowed

• mandatory

• optional

Multiple Choice

Detailed Inspection (DI) is an intensive examination of a specific item, installation, or assembly to detect damage, failure or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses etc. may be necessary. Surface cleaning and elaborate access procedures may be required.

What can be inferred from the passage?

• DI can be done with an indirect source of good lighting.

• DI is an examination of an interior area.

• Mirrors and magnifying lenses are the only items needed.

• DI is an examination of one part.

Multiple Choice

Detailed Inspection (DI) is an intensive examination of a specific item, installation, or assembly to detect damage, failure or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses etc. may be necessary. Surface cleaning and elaborate access procedures may be required.

What is a procedure that may need to be done in a detailed inspection?

• General accessing

• Surface cleaning

• Surface heating

• Physical distancing

Multiple Choice

Detailed Inspection (DI) is an intensive examination of a specific item, installation, or assembly to detect damage, failure or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses etc. may be necessary. Surface cleaning and elaborate access procedures may be required.

What is the purpose of a DI?

• to detect damage, failure, or irregularity.

• to trouble-shoot damage, failure, or irregularity.

• to make damage, failure, or irregularity.

• to ignore damage, failure, or irregularity.

Multiple Choice

Maintenance messages related to the fuel system can possibly occur during the first engine start. The cause of these messages can be air that went into the system during the related fuel drain procedure. This air will be removed automatically during the first engine ground run. Thus, during subsequent engine starts the messages should not show again, unless they are caused differently.

What can be the cause of maintenance messages related to the fuel system?

• The air cooling in the system

• The air that went out of the system

• The air that heated in the system

• The air that went into the system

Multiple Choice

Maintenance messages related to the fuel system can possibly occur during the first engine start. The cause of these messages can be air that went into the system during the related fuel drain procedure. This air will be removed automatically during the first engine ground run. Thus, during subsequent engine starts the messages should not show again, unless they are caused differently

When do the maintenance messages related to fuel system possibly occur?

• During subsequent engine starts

• During the first engine start

• During the first engine ground on

• During the related fuel drain procedure

Multiple Choice

Maintenance messages related to the fuel system can possibly occur during the first engine start. The cause of these messages can be air that went into the system during the related fuel drain procedure. This air will be removed automatically during the first engine ground run. Thus, during subsequent engine starts the messages should not show again, unless they are caused differently

During the first engine ground run, the air is removed how?

• Manually

• Voluntarily

• Systematically

• Supposedly

Multiple Choice

Wet motoring the engine is necessary to test the fuel system. When an engine is wet motored, the two ignition systems are turned OFF and the starter is engaged to turn the HP rotor to 15% - 20% N2. At N2 = 15%, the HP fuel shutoff valve control lever is moved to ON and the engine exhaust nozzle is carefully monitored for any sign of fuel. The test can be continued in accordance with starter duty cycle limitations.

Why is it necessary to wet motor the engine?

• To examine the fuel system

• To increase the engine's power

• To test the hydraulic system

• To test the electrical system

Multiple Choice

Wet motoring the engine is necessary to test the fuel system. When an engine is wet motored, the two ignition systems are turned OFF and the starter is engaged to turn the HP rotor to 15% - 20% N2. At N2 = 15%, the HP fuel shutoff valve control lever is moved to ON and the engine exhaust nozzle is carefully monitored for any sign of fuel. The test can be continued in accordance with starter duty cycle limitations.

 During wet motoring, what is the position of the ignition systems?

• Both are turned ON

• Both are turned OFF

• One is turned OFF, the other is turned ON

• The position of the ignition systems does not matter during wet motoring

Multiple Choice

Wet motoring the engine is necessary to test the fuel system. When an engine is wet motored, the two ignition systems are turned OFF and the starter is engaged to turn the HP rotor to 15% - 20% N2. At N2 = 15%, the HP fuel shutoff valve control lever is moved to ON and the engine exhaust nozzle is carefully monitored for any sign of fuel. The test can be continued in accordance with starter duty cycle limitations.

What should be carefully monitored during wet motoring?

• The hydraulic system pressure.

• The engine oil temperature

• The RPM of the LP rotor

• The engine exhaust nozzle for any sign of fuel

Multiple Choice

Similar doors on opposite sides of the aircraft have the same letter identifier.

• Uçağın karşılıklı yan taraflarındaki kapılar aynı harf koduna sahiptir.

• Uçaktaki karşı taraflardaki benzer kapılar aynı harf kodu ile tanımlanmıştır.

• Uçağın karşılıklı yanlarındaki benzer kapılar aynı harf tanımlayıcısına sahiptir.

• Uçağın karşılıklı yan taraflarındaki benzer kapılar aynı harf koduyla tanımlanır.

Multiple Choice

Discharge heads should be clean and free from foreign objects.

• Tahliye başlıkları temiz ve yabancı cisimlerden arınmış olmalıdır.

• Tahliye başlıkları temiz ve yabancı cisimlerden arınmış olacaktır.

• Tahliye başlıkları temizlenmeli ve yabancı cisimlerden arındırılmalıdır.

• Tahliye başlıkları temiz olmalı ve yabancı cisimler arındırılmalıdır.

Multiple Choice

Any high-frequency eddy current equipment may be used provided that it meets the requirements of this procedure

• Bu prosedürün gerekliliklerini karşılaması koşuluyla herhangi bir yüksek frekanslı eddy akımı ekipmanı kullanılacaktır.

• Bu prosedürün gerekliliklerini karşılaması koşuluyla herhangi bir yüksek frekanslı eddy akımı ekipmanı kullanılabilir.

• Bu prosedürün gerekliliklerini karşılaması koşuluyla herhangi bir yüksek frekanslı eddy akımı ekipmanı kullanılır.

• Bu prosedürün gerekliliklerini karşılaması koşuluyla herhangi bir yüksek frekanslı eddy akımı ekipmanını kullanabilirsiniz.

Multiple Choice

Additional certification requirements may impose additional restrictions

• Ek sertifikasyon gereklilikleri, ek kısıtlamaları uygulama ihtiyacı doğurabilir.

• Ek sertifikasyon gereksinimleri ek kısıtlayıcı şartlar talep edebilir.

• Ek sertifikasyon gereklilikleri ek kısıtlamaları beraberinde getirir.

• Ek sertifikasyon gereklilikleri ek kısıtlamalar getirebilir.

Multiple Choice

If you do the resistance check from the avionics compartment, you must disconnect all the transducers, but not the one in test.

• Direnç kontrolünü aviyonik bölmeden yaparsanız, test edilen hariç tüm transdüserlerin bağlantısını kesmeniz gerekir.

• Direnç kontrolü aviyonik bölmeden yapılırsa, test edilen hariç tüm transdüserlerin bağlantısının kesilmesi gerekir.

• Direnç kontrolünü aviyonik bölmeden yaparsanız, test edilen hariç tüm transdüserlerin bağlantısını yapmanız gerekir.

• Direnç kontrolünü aviyonik bölmeden yapsaydınız, test edilen hariç tüm transdüserlerin bağlantısını kesmeniz gerekirdi.

Multiple Choice

Bazı otopilot kurulumları uçuş direktörünün çalışır halde olmasına bağlı değildir ve temel hareket modları hala mevcut olabilir.

• Every autopilot installation does not depend on flight director being operative, and basic attitude modes may still be available.

• Some autopilot installations are not dependent on flight director being operative, and basic attitude modes may still be available

• Some autopilot installations do not depend on flight director being operative, and basic attitude modes may still be available.

• Some autopilot installations are not dependent on flight director being operative, but basic attitude modes may still be available.

Multiple Choice

Ön camın montajından sonra güvenlik klipslerini ve etiketleri çıkarın ve devre şalterlerini belirtilen şekilde kapatın.

• Remove the safety clips and tags, and close the circuit breakers specially after the installation of the windshield.

• Remove the safety clips and tags as specified, and close the circuit breakers after the installation of the windshield

• Remove the safety clips and tags, and close the circuit breakers as specified after the installation of the windshield.

• As specified, remove the safety clips and tags, and close the circuit breakers after the installation of the windshield.

Multiple Choice

Kadmiyum kaplamalı parçalara dokunmadan veya bakım yapmadan önce aşağıdaki uyarılara uyun.

• Obey the warnings below before you touch or do maintenance on parts that are cadmium plated.

• It is recommended to obey the warnings below before you touch or do maintenance on parts that are cadmium plated.

• Obey the warnings below as you touch or do maintenance on parts that are cadmium plated

• It is a must to obey the warnings below before you touch or do maintenance on cadmium plated parts.

Multiple Choice

Bazı parçalarda, asbest içeren materyal, bir yapıştırıcı içinde olabilir.

• In some parts, the material that contains asbestos may be within an adhesive.

• In certain parts, the material that contains asbestos may be within an adhesive.

• In some parts, the material that contains asbestos must be within an adhesive.

• In some parts, the material that is contained asbestos may be with an adhesive.

Multiple Choice

34) … sure that the probes, the engine, and the APU 35) … cool before installation of the protective devices. If the probes are 36) …, there is a risk of injury, and the protective devices can melt.

• Do

• Get

• Make

• Have

Multiple Choice

34) … sure that the probes, the engine, and the APU 35) … cool before installation of the protective devices. If the probes are 36) …, there is a risk of injury, and the protective devices can melt.

• is

• are

• isn’t

• aren’t

Multiple Choice

34) … sure that the probes, the engine, and the APU 35) … cool before installation of the protective devices. If the probes are 36) …, there is a risk of injury, and the protective devices can melt.

• hot

•  cold

• mild

• cool

Multiple Choice

In some procedures that are not new, it is possible that a NOTE statement will include 37) … or dimensional limits (for example, feature controls). If a NOTE statement 38) … instructions or dimensional limits, then it is necessary to obey this information because it is necessary 39) … the procedure.

• inquiries

• inspirations

• inspectors

• instructions

Multiple Choice

In some procedures that are not new, it is possible that a NOTE statement will include 37) … or dimensional limits (for example, feature controls). If a NOTE statement 38) … instructions or dimensional limits, then it is necessary to obey this information because it is necessary 39) … the procedure.

• includes

• will include

• is included

• included

Multiple Choice

In some procedures that are not new, it is possible that a NOTE statement will include 37) … or dimensional limits (for example, feature controls). If a NOTE statement 38) … instructions or dimensional limits, then it is necessary to obey this information because it is necessary 39) … the procedure.

• to complete

• to be completed

• completing

• completed

Multiple Choice

Keep brake assemblies in storage …………… rain, snow, or dew.

• out under

• away from

• within

• up above

Multiple Choice

If installation is correct, no further action …………..

• is not required

• requires

• is required

• required

Multiple Choice

If an inoperative armrest will hinder an emergency evacuation or any other flight duties, it ………… removed.

• should be

• should have been

• could be

• could have been

Multiple Choice

NOTE: All equipment removed, or zones behind access panels removed to get access during a maintenance operation,

…………………………………………………………………………

• will have to examine before re-installation.

• must also have been examined before re-installation.

• must also be examined before re-installation

• must also examine before re-installation.

Multiple Choice

…………………………………, the loads that are permanently connected will decrease the battery charge to a very low level.

• If the battery stays connected during parking

• If the battery stayed connected during parking

• If the battery stays disconnected during parking

• If the battery stayed disconnected during parking

Multiple Choice

If a part, tool, or object falls into the engine, ……………………….……… ….…………………………….

• the assembly process should not stop until the fallen articles are found.

• the assembly process cannot stop until the fallen articles are found.

• the assembly process must stop until the fallen articles are found.

• the assembly process will stop until the fallen articles are found.

Multiple Choice

The basic cylinder of all types of extinguisher ………………… …………………………………

•  is consisted of a seamless aluminum cylindrical container.

• consisted of a seamless aluminum cylindrical container.

• consists of a seamless aluminum cylindrical container.

• consist of a seamless aluminum cylindrical container.

Multiple Choice

……………………………….   are required for cleaning.

• No special materials

• Every special material

• A special material

• Some special material

Multiple Choice

After you touch cadmium plated parts, ………………………… ………………………………….

• clean your hands, before eat or smoke.

• clean your hands after you eat or smoke.

• clean your hands while you eat or smoke.

• clean your hands before you eat or smoke.