NEW
Font size
WorksheetsFinal Exam Review - Part 2
Total questions: 19
Worksheet time: 10mins
What is the best way to make deep cuts with a router?
With the longest bit available.
In several passes.
Using very firm pressure.
On a routing table.
When you install a belt on a portable belt sander, what do you align with the arrow on the sander?
The belt's lap seam.
The lock on top of sander.
The top handle of the sander.
The arrow inside the belt.
What type of sander can be used either with wood's grain or against it?
4" by 24" belt sander.
Finishing sander.
Orbital sander.
Random-orbit sander.
Always make sure a power tool is ______________ when you install, remove, or adjust bits.
turned off
set down firmly
pointing away from you
unplugged from its power source
The tow-step firing sequence of newer power fasteners requires that the tool's nose piece be _______________ or the tool won't fire.
pointed downward
double-triggered
against the work piece
perfectly clean
You should release the pressure from an air compressor at the end of every work day and ................
before transporting it.
when it's unused for over an hour.
during your breaks.
if its used indoors.
Which of the following statements about engineered lumber is true?
Overall performance is highly unpredictable.
It uses wood that might otherwise be wasted.
It is available in limited dimensions.
Its defects are similar to solid wood but are made stronger.
One advantage of using engineered lumber over solid lumber is that it ............................
doesn't shrink and swell as much.
is heavier than solid lumber.
is available in limited lengths.
can be stored outside without worry of moisture damage.
How can you determine the grade of a piece of plywood?
Use product information brochures provided by the seller.
Compare the plywood to a standard grading chart.
You need to be able to identify them on sight.
The grade should be stamped on the plywood.
When laying out joists, how far from the corner of the sill plate should be first joist be located?
16".
24".
14 1/4".
15 1/4".
What is the outermost curve of an edgewise how on a joist?
Crown.
Bridging.
Web.
Cantilever.
If you use the "3-4-5 rule," which of these sets of wall measurements forms a 90 degree angle?
6' x 8' with 9.5' between them.
18' x 24' with 29' between them.
15' x 21' with 27' between them.
12' x 16' with 20 between them.
To lie out a wall's first opening, measure ___________________ to the center of the opening.
The nearest stud.
The centers of the nearest studs on each side.
Both sides of the opening.
One corner of the building.
How can you determine the rough opening size required for a door?
Take the width and length measurements directly from the door.
Check standard measurements used for all rough openings.
Check the door schedule in the building plans.
Use a carpenter's layout template to mark the plate.
How can you estimate the number of 16" OC studs needed for exterior walls?
Figure one stud per every 16 lineal inches of wall.
Figure one stud per lineal foot of wall.
Figure one stud per every 8 lineal inches of wall.
Figure one stud per every 32 lineal inches of wall.
For walls with a double top plate, how do you figure the total length of top and bottom plates needed?
Multiply the wall length by three.
Multiply the wall length by two.
Divide the wall length by three.
Divide the wall length by two.
How can you determine the number of 4 x 8 plywood sheets needed to sheathe a house?
Determine the total square footage of floor space and divide by 32.
Add together the lengths of all four walls and divide by 12.
Determine the total wall area and divide by 32.
Multiply the house's length by its width and divide by 8.
When you ____________ a wall, it means you make sure it is perpendicular (at a right angle) to the sub floor.
plumb
square
partition
block
Why do builders use a double plate above the top plate of a wall?
To add strength from a better quality of material used.
To add strength with this thicker piece of plate.
To tie the walls together at the top.
To tie the windows together at the top.
