These diagrams will show a three-dimensional representation of the system or component and then display the general physical location of all other components within that system.

_____________ are useful when trying to explain a system using general descriptions instead of pictures or symbols.

______________ are very similar to Block diagrams, but instead of blocks, symbols are used to identify the major components of the system.

______________ use symbols to represent the different components in a system.

______________ use symbols to represent the different components in a system.

________________ shows even more detail, such as each individual contact number within each specific component

A _______________ explains complex digital systems in a way that is easy to read and understand

_____________________ diagrams are important for the physical engineering and construction of electrical facilities.

What are the 2 common schematic diagram?

Wiring diagrams are NOT often used when installing and troubleshooting equipment.

The best method for reading a ladder diagram is to start at the UPPER RIGHT of the diagram.

_______________ is represented by 2 vertical lines in the ladder diagram.

If the supply is DC, the left side of the rail is POSITIVE and the right side is NEGATIVE.

In ladder diagram, _____________ devices are used to perform logic functions that control the output devices.

In ladder diagram, _____________ devices cause the machine to perform its operation.

_____________ are the electrical wires that connect the circuit.

Each component in a ladder diagram should be labeled with its function and a way to identify it.

This logic gate is called a (an) _____________ gate.

This logic gate is called a (an) _____________ gate.

This logic gate is called a (an) _____________ gate.

This logic gate is called a (an) _____________ gate.

This logic gate is called a (an) _____________ gate.

This logic gate is called a (an) _____________ gate.

This logic gate is called a (an) _____________ gate.

Electrical panels protect workers from accidental contact with electrical components.

Electrical panels protect components against harmful atmospheric and environmental conditions.

Two commonly used standards for degree of protection for electrical panels.

According to NEMA, a HAZARDOUS location is where an ________________________ might occur.

The first digit of IP protection describes the degree of protection for a (1)_______________ while the second digit describes the degree of protection against (2)_________________.

The IEC enclosure does not include protection against mechanical damage, explosions, condensation or corrosive vapors.

The IEC enclosure does not include protection against mechanical damage, explosions, condensation or corrosive vapors.

To help workers to identify a particular wire, panel builder attach _________ to each wire.

The technician must ensure that wire numbers should match to the numbers on the print.

In numbering ladder diagram, all devices that are connected to the LEFT use wire number _____________.

In numbering ladder diagram, all devices that are connected to the RIGHT use wire number _____________.

Wire number change after passing each control device except for _______________ device.

Wire number change after passing each control device except for circuit protection device.

Wires from internal panel components connect to the terminal block facing inside the panel

Wires are not allowed to cross the terminal block

No more than 2 wire connections are allowed per terminal

________________ provide a convenient location for numbering the wires in a panel according to the print.

TERMINAL BLOCKS provide a convenient location for numbering the wires in a panel according to the print.

Terminal blocks are commonly installed in ______________.

TERMINAL BLOCKS are commonly installed in DIN RAIL.

From the picture shown, the circuit breaker is mounted in DIN RAIL.

A control panel contains devices such as motor starters, control relays, timers and control transformers

What do you call this device?

What do you call this device?

Start button has ___________ contact.

Stop button has ___________ contact.

The color of a STOP push button is ____________.

The terminal number of magnetic contactor coil is _________.

The main contact terminal number of magnetic contactor in the SUPPLY side is _______________.

The main contact terminal number of magnetic contactor in the LOAD side is _______________.

The NO auxiliary contact terminal number of magnetic contactor is ______________.

The NC auxiliary contact terminal number of magnetic contactor is ______________.

The NC terminal number of overload relay is

The NO terminal number of overload relay is

The pushbutton return to its original position when released.