NEW
Font size
S
M
L
XL
WorksheetsModel IV_PPCE_2 Marks
Total questions: 15
Worksheet time: 15mins
Name
Class
Date
1.
The output of process planning is
a)
Route Sheet
b)
Sequence sheet
c)
Bar chart
d)
None of above
2.
The business objectives of process planning are
a)
Sales
b)
Cost Reduction
c)
Effective use of facilities
d)
All the above
3.
A drawing where one or two dimensions of a component are variable, the drawing is known as
a)
Single part drawing
b)
Collective single part drawing
c)
Assemble drawing
d)
Arrangement drawing
4.
Consider the following statements: The break-even point increases 1. If the fixed cost per unit increases 2. If the variable cost per unit decreases 3. If the selling price per unit decreases Which of the above statements is/are correct?
a)
1 only
b)
1 and 2
c)
2 and 3
d)
1 and 3
5.
Value of stock of material as on 1.09.2019 is Rs.26,000 ; Material purchased = Rs.274000; Wages to labour= Rs.120000; Value of stock of material as on 31.08.2020 is Rs.36,000 Direct expenses = Rs.5000. Determine the prime cost.
a)
Rs.384000
b)
Rs.389000
c)
Rs.353000
d)
Rs.375000
6.
A power hacksaw machine was purchased for Rs.25,000. After 5years the machine was valued at Rs.I0,000. Find out the depreciiuion amount according to the sinking fund method, the rate of interest being 5%.
a)
Rs.2715
b)
Rs2785
c)
Rs3755
d)
Rs.3795
7.
The volume and weight of filler rod used for welding are 10cc and 0.01Kg/cc. If the cost of filler rod is Rs.50 per Kg, the actual cost of filler material for 50 components is _____
a)
Rs.200
b)
Rs.250
c)
Rs.300
d)
Rs.350
8.
The net volume and weight of forged component are 50cc and 400gms respectively. If shear loss and scale loss each are 5 percent of net weight and other losses are negligible, Gross weight of component is _______-
a)
440gms
b)
445gms
c)
450gms
d)
455gms
9.
Labour cost per product is Rs. 2/hr and time taken by each product is 2 hr. The factory overhead is 20% of the labour costs. The factory cost for 100 products if material cost per product is Rs. 3, is.
a)
Rs. 700
b)
Rs. 740
c)
Rs. 780
d)
Rs. 820
10.
A 10 cm thick laminated plate consists of a 7 cm thick brass and a 3 cm thick mild steel plate. A 20 mm diameter hole is to be drilled through the plate. Estimate the total time taken for drilling if, Cutting speed for brass = 500rpm, Cutting speed for mild steel = 400rpm and feed of drill for both steel & brass = 0.25mm per revolution.
a)
45 sec
b)
60 sec
c)
75 sec
d)
90 sec
11.
Estimate the time required for cutting 3 mm pitch threads on a mild steel bar of 2.8cm diameter and 8cm long. Assume the cutting speed for threading as 170rpm.
a)
1.25min
b)
3min
c)
4.5min
d)
6min
12.
Find the time required to face a job 20 cm long and 10 cm wide with the help of milling cutter having of diameter 10cm with 8 teeth and revolving at 100 rpm. The feed per tooth should not exceed 0.125 mm.
a)
2.5min
b)
3.5min
c)
4.5min
d)
5.5min
13.
If the fixed cost of the assets for a given period doubles, then how much will the break-even quantity become?
a)
Half the original value
b)
Same as the original value
c)
Twice the original value
d)
Four times the original value
14.
Last year, a manufacturer produced 15000 products which were sold for Rs. 300 each. At that volume, the fixed costs were Rs.15.2 lacs and total variable costs were Rs. 21 lacs. The break even quantity of product would be:
a)
4000
b)
7800
c)
8400
d)
9500
15.
In a manual operation, observed time for a cycle of operation is 0.5 minute and the rating factor as observed by the time study engineer is 125%. All allowances put together is 15% of N.T. (Normal Time). Estimate the Standard Time.
a)
0.72 min
b)
0.5 min
c)
1 min
d)
1.2 min
Reset
