WorksheetsEEOM Quiz 2
Total questions: 36
Worksheet time: 18mins
All are T-41 ALTERNATOR specifications except?
28 Volts
38 ampere rating
Connected to the engine through accessory housing
Encased in an alloy housing
My specifications are:
- Lead Acid
- 12 Cell
- 24 Volts
- 17 Ampere-hour
- Quick Disconnect fitting
- Installed in the tail cone aft of baggage compartment
What am I?
(a)
Specifications:
- 28 Volt standard AN type receptacle
- Use for cold weather starting or when lengthy electrical maintenance.
- With reverse polarity protection
What am I?
(a)
I am the primary source of electrical power. What am I?
(a)
Specifications:
- Located at the upper right of the firewall
- Solid-state
- Remove and replace item
- Not repairable
- Regulates the alternator field current
What am I?
(a)
Specifications:
- Located at the firewall
- Remove and replace item
- Non-repairable
- Open the over voltage warning light when the voltage reading is 32 Volts and simultaneously shuts off the alternator.
What am I?
(a)
Specifications:
Press to test light Located on the lower right side of the instrument panel Illuminate anytime electrical system voltage exceeds approximately 32 volts.
What am I?
(a)
Specifications:
- Toggle type switch
- Located beside the throttle control lever
- Installed with a switch guard
- The function is to apply or remove power to the alternator field circuit
What am I?
(a)
Specifications:
- Located on the right side of the instrument panel
- Indicates a charging or discharging condition
- Also indicates the flow of electricity, in amperes, from the alternator to the battery or from the battery to the aircraft electrical system.
What am I?
(a)
Tick the battery system components.
Battery
Battery Contactor
Master Switch
Circuit Breakers and Fuses
Alternator
Specifications:
- Mounted beside the battery box
- Plunger type contactor
- Actuated by the Master Switch
What am I?
(a)
Specifications:
- Located on the lower switch and control panel
- Push-Pull type
- Pulled-On
- Pushed-Off
What am I?
(a)
Specifications:
- Mounted on the lower switch and control panel
- Labeled according to their funcion and aperage
- Push to reset type
- Must cool before it can be reset
- If the breaker trips after reset, do not attempt to reset again.
What am I?
(a)
Tick all ALTERNATING SYSTEM COMPONENTS.
Ammeter
Voltage Regulator
Over Voltage Relay
Over Warning Voltage Warning Light
Alternator Switch
All are electrical power source EXCEPT?
Alternator
Battery
External Power
Solenoid
Resultant torque is with respect to time in OC RELAY USING INDUCTION DISC
True
False
Time setting is not available in this relay
instantaneous over current relay
Over current relay
directional relay
none of them
The input(s) of overcurrent relay is (are)
Current
voltage
both current and voltage
directional unit input
Most occurrence fault
L-G
LLG
LL
Three phase fault
Lengthiest part of power system
generation system
transmission system
distribution system
consumer part
Two way power flow available in
Restructured power system
conventional power system
smart grid
deregulated power system
What are they called?
pliers
scissors
screwdrivers
wire strippers
What are they?
scissores
screwdrivers
pliers
cable strippers
We make holes by this tool.
clamp
drilling machine
hammer
soldering
These are tools manipulated by hands without using electrical energy such as puller, hacksaw, pull-push rule, pliers, hammer and others.
Hand Tools
Power Tools
Pneumatic Tools
Electrical Tools
These are tools manipulated by our hands and with the use of electrical energy such as electric drill, grinding wheels, vacuum cleaner, and others.
Power Tools
Hand Tools
Pneumatic Tools
Electrical Tools
These are designed around three basic devices: the air cylinder, the vane motor, and the sprayer.
Power Tools
Hand Tools
Machine Tools
Pneumatic Tools
These are used to turn screws, nuts, and bolts with hexagonal or six-sided heads. A variety of wrenches are used in the shop.
Wrenches
Screwdrivers
Hammers
Pliers
These are used to remove gears and hubs from shafts, bushings from blind holes, and cylinder liners from engine blocks.
Screwdrivers
Wrenches
Hammers
Pliers
These are used to drive or turn screws
Pullers
Wrenches
Hammers
Screwdrivers
This can be either bench-mounted or installed on a pedestal
Electric drill
Vacuum cleaner
Pneumatic Torque Wrench.
Grinding tool
This refers to the visual observation of an expert on the appearance of the tools and equipment.
Visual inspection
Performance
Persons involved
Power supply
When there is something wrong with the performance of either hand tools or equipment, they need immediate repair or maintenance.
Visual inspection
Persons Involved
Performance
Power supply
Failure to meet the required power supply will result in a malfunction.
Power supply
Persons Involved
Performance
Functionality
Vibration or extra noise from the operation means problems with parts and accessories are starting to develop.
Visual Inspection
Persons Involved
Performance
Functionality
It refers to the technical person who has the knowledge and skills about the technology.
Visual Inspection
Persons Involved
Power Supply
Functionality
