WorksheetsCT111 MIDTERM
Total questions: 50
Worksheet time: 25mins
An instrument used to measure the amount of resistance.
voltmeter
ohmmeter
multi-tester
ammeter
A voltage will influence current only if the circuit is:
open
insulated
high resistance
closed
Primary batteries, unlike secondary batteries, may be:
charged once
used once
recharged over and over
stored indefinitely
This type of variable resistor with 3 contacts is usually used to control voltage.
light dependent resistor
potentiometer
rheostat
preset
Which of the following is the component symbol for light emitting diodes?
Which of the following is the component symbol for photo diodes?
What are the unit and symbol for current?
Ampere, A
Coulomb, I
Ampere, Q
Ampere, I
The circuit symbol, represents what type of switch?
2-way changeover switch
on-off switch
dual on-off switch
reversing switch
Which of the following circuit symbol is used to measure current?
Batte
A switch is a device that:
short circuits complex circuits
holds a fuse
has double poles
opens or completes a current path
The component symbol that converts sound to electrical energy is
The component symbol that converts electrical energy to sound is
The component symbol that converts electrical energy to sound is
The electronic component used to step up (increase) and/or step down (decrease) AC voltages.
cell
battery
fuse
transformer
An ammeter is used to measure
voltage
current
resistance
All of the above
This type of variable resistor with 2 contacts is usually used to control current.
fixed resistor
rheostat
potentiometer
preset
Current is:
the presence of a positive charge
the abundance of electrons
the movement of electrons
the repulsion of electrons
A short circuit will have:
a small current flow
a large current flow
no current flow
some current flow
A type of switch that is electrically operated.
SPST
reversing
relay
DPDT
A special diode which is used to maintain a fixed voltage across its terminals.
light emitting diode
zener diode
photodiode
general diode
Which of the following capacitor needs to be connected the correct way round?
general capacitor
polarized capacitor
variable capacitor
trimmer capacitor
Which of the following is not a type of energy source?
generator
rheostat
solar cell
battery
A thermistor is a type of
switch
resistor
battery
power supply
A two-terminal variable resistor is known as a
potentiometer
thermistor
rheostat
wiper
Fuses and circuit breakers are designed to ___ when excessive current flows.
buzz
illuminate
close
open
A multimeter measures
current
voltage
resistance
current, voltage, and resistance
A circuit breaker is a
fuse
switch
resettable protective device
resistor
What type of switch is this?
push button
SPST
DPDT
SPDT
Which of the following is not an advantage of implementing 5S technique?
To standardize work practices
To create a dirty workplace
To improve work efficiency
To improve work discipline
What phase of 5S are we talking about when we regulate how we color code our tools how we
use the red tag system?
Set in order
Shine
Standardize
Sort
Which of the following from the 5S technique means ‘to clean the workplace, everything, everyday,
without fail’?
Seiri
Seiketsu
Seiso
Seiton
The acronym for proper use of a fire extinguisher is:
PALS
PAST
PASS
None of the Above
What is the designation for fires involving cooking oils or fats?
Class C
Class B
Class K
Class A
The three elements of the fire triangle are:
Water, a heat source, and fuel
Fuel, oxygen, and earth
Oxygen, fuel, and a heat source
Oxygen, water, and fuel
Carbon Dioxide extinguishers are designed for which types of fuels?
Class A and C
Class A and B
Class B and C
Class A, B and C
An example of two “Class B” fuels would be:
Cardboard, newspapers
Grease, paint thinner
Cardboard, newspapers
All of the Above
Any unplanned or uncontrolled event resulting from unsafe acts/unsafe occupational
conditioning either of which can cause injury
Injury
Fire
Accident
Incident
Its a needle like that move on the scale of VOM
Zero Corrector
Pointer
Zero Ohm Adjustment
Selector Knob
It used to zero-in the pointer in measuring resistance.
Probe
needle corrector
Scale
Zero Ohm Adjustment
It used to connect the circuit and the electronic component to be measure
Pointer
Zero Ohm Adjustment
Scale
Test Probe
What is the best thing to do if the pointer doesn’t reach the zero position when connecting the test probes before taking any resistance measurement?
Continue to measure the resistance
Replace the batteries
Change the resistor
Replace the multitester
When measuring the voltage of batteries, what range setting wil you select in the range selector knob?
DCA
DCV
Ω
ACV
In reading the amount of voltage, always start with the______?
Highest range
Lowest range
Any range
None of the above
As a capacitor is being charged, the voltage across its terminals will:
increase
decrease
remain the same
oppose the source
What electronic symbol is shown?
NAND gate
OR Gate
EXOR Gate
NOT Gate
What electronic symbol is shown?
SPST Switch
DPST Switch
SPDT Switch
DPDT Switch
Identify the symbol?
Signal Ground
Chassis Ground
Dipole Antenna
Aerial Antenna
What electronic symbol is shown?
Voltmeter
Galvanometer
oscilloscope
thermistor
What electronic symbol is shown?
Voltmeter
Galvanometer
oscilloscope
thermistor
What electronic symbol is shown?
Voltmeter
Galvanometer
oscilloscope
thermistor
