A parametric modeler is controlled by:

The ___ key(s) is used to launch the shortcut menu.

The design intent of this part is to have the hole centered on the front face. If you change the 100mm dimension to 75mm and the 150mm dimension to 200mm, will the hole remain centered?

The shortcut menu shown in the image is activated by:

You can create a custom Named View from the Camera and Render Options.

Which of the following are correct?

I. Hold the right mouse button to rotate the model on the screen.

II. To pan the model, hold down the Ctrl key and the right mouse button .

III. Use the mouse scroll wheel to zoom in and out of the model.

In what ways can you share documents?

You can reset changes made to a document by restoring a previous version to the current workspace.

If you make changes to a branch, they will reflect in the main workspace.

What methods can you use to switch to an Isometric view?

Projected views are different from model views because _____________________________.

You can only use the default configuration of an assembly to drive a Bill of Materials.

If you delete a driving dimension from a drawing view, the dimension will also be deleted from the model.

To create an exploded view in a drawing, the assembly file must already have an exploded configuration.

Which of the following tools can be used to add new views to a drawing?

After creating the first model view, Onshape places you into Projected View mode where you can add projected views of the model view.

In a drawing, if a dimension on a projected view is manually changed, that dimension on all of the other views will update as well.

Hole callouts appear in gray because they are driven by the hole information from the part file.

When you modify the size and location of the detail circle in the parent view, the detail view updates dynamically.

If you move a section view after it has been created, the section view`s alignment with the parent view will be broken.

A Bill of Materials can only be created within the drawing environment.

When you attach a balloon to a face or an edge, it is attached with an arrow.

If you change the View Orientation of a parent view or projected view, any other linked views will also change in orientation.

Which of the following is the icon for Callout?

Part Sketches can be used for mate relationships in assemblies.

Dashed line types shows there are multiple edges stacked in the drawing.

Each drawing sheet represents a new unique part.

A "+" on the drawing is always the center of an arc or circle.

A part dimensioned "0.500" has the same acceptable deviation as a part dimensioned "0.5".

Tolerances in the title block over-ride a dimension's tolerances.

Part numbers and descriptions help identify the part in the drawing.

Individual view scales always match the sheet scale.

Assembly items can be pulled from multiple documents and standard content.

Best practice is to copy documents then merge parts together when multiple users need to work on the same document.

When adding a mate, using rotate ____________.

For parts split into two pieces best practice is to __________.

__________ designate a reference dimension.

The ______ symbol represents a counterbore.

When a 12in long part is scaled 1:4, it appears to be ___in long on the paper.

What symbol represents a diameter?

What balloon symbol is associated with a Bill of Materials Line?

A projected view has an associated ___________ view.

When detailing a symmetric part that is not a revolved piece what line shows the part is symmetric.

What is the most important part of a revision block?

A ______ view type is based on an imaginary cut across the part.

When a small piece of information needs to be shown close up, a ____ view is best.

A bill of material is typically found _________.

Dashed lines on an assembly drawing are called _________ lines.

A drawing view normal to an angled faces is called a(n) _____ view.

Using the ________ feature can shorten long sections in a drawing view.

In order to save a design state, it's best practice to _______.

Which of the following is not a tab type found in Onshape?

When a document is shared, the third party has access to ____________ within the document

What can you NOT view in Follow mode?

To simulate or show motion in an assembly you must maintain at least one degree of freedom.

True or False: When creating an Exploded View, you can move multiple components at the same time in a single step.

Top-Down design involves creating a layout within an assembly and then designing the parts within the assembly environment.

The symbol next to the first part listed in the Instance List indicates ______.

True or False: You can insert a part into an assembly by dragging the part file from Windows Explorer into the Onshape window and dropping it in your assembly.

To rotate a single part within an assembly, click and drag it using the:

True or False: You cannot apply mates between the face of a model and a reference plane.

To use Snap Mode _______.

A Mate Connector can be placed on a vertex, midpoint of an edge, or the center of circular geometry.

True or False: You cannot flip the alignment of a mate while editing a mate.

A Fastened mate allows a part to translate along a single axis.

If you make a change to only one instance of a standard content component, it will automatically change every other instance that uses the same specifications.

To add additional copies of a component into an assembly:

What does the `M` stand for in a bolt with the sizing `M10`?

One way to remove an existing sketch entity is to select it and then press the __________ key on the keyboard.

True or False: You can double-click a feature in the graphics area to display its dimensions.

When box-selecting multiple items, to include only items completely enclosed within the box, drag the selection box from left to right.

Which of the following signify that a sketch is fully defined?

If you select a face to draw a sketch, the sketch entities cannot extend beyond the edges of that face.

The units of a document can be changed under Workspace Units in the Document Menu.

Which of the following is an indicator that you are in sketch mode?

To select multiple sketch entities, _________.

Which of the following is NOT a type of arc in Onshape?

You can fully define the shape and size of a sketch using only dimensions and geometric constraints.

If an endpoint of a line has a defined horizontal geometric constraint, and is dragged in any direction, it will maintain its horizontal constraint.

Which of the following geometric constraint flags indicate that sketch entities are coincident?

Which constraint has NOT been defined for the 2 segments shown?

What will happen when a sketch becomes over defined?

While in sketch mode, the number displayed near a sketch entity represents the sketch element`s exact size. Therefore, there is no need to add a dimension to set the dimensional value.

When sketched geometry is displayed in blue, the geometry is considered:

The Extrude feature can be used to remove material.

Which end type of an Extrude is used to add an equal amount of material to both sides of the sketch plane?

In order to create two-dimensional geometry such as lines, arcs, and rectangles, what mode should Onshape be in?

After an extruded feature has been created, you can always go back and edit the feature. When you edit an existing extrude feature, which of the following cannot be changed while editing the feature?

To edit an existing feature, right click on the feature in the Feature List and select "Edit Sketch."

How can you sketch the rectangle showing in the image so that the center of the rectangle and the origin coincide in the least number of clicks?

When sketched geometry is displayed in black, the geometry is considered:

Which icon would you click to activate the Dimension tool and add dimensions to a sketch?

Which type of Arc requires another entity to specify its start point?

When you select multiple edges to Chamfer, a flag is displayed on each edge and each one can be given individual Chamfer dimensions.

True or False: It is possible to add material to a part using a Chamfer feature.

You can create a plane at an offset distance by selecting a plane or a planar face as the reference.

If there is an existing centerline in a sketch, like the one in the sketch shown, then Onshape will automatically pre-select it as the revolve axis of a Revolved feature regardless of its position or orientation.

Which option needs to be selected from the Revolve Type drop-down list to revolve the sketch shown evenly on both sides of the sketch plane?

This feature is an example of a(n) ________.

A temporary axis is automatically created by Onshape for any part that has a circular edge or face.

Which check box in the Circular Pattern tool do you select so that the number of instances will always be evenly distributed?

Which feature would you most likely use to create the holes shown in the image?

The design intent of this part requires that the sketched circle be vertically aligned to the origin. Does the image shown indicate that this design intent has been achieved?

Which check box is selected to make sure that patterned instances are created on both sides of the original hole in the middle?

Which of the following can NOT be edited while using the Rib tool?

The Hollow option in the Shell tool allows you to create closed, thin-wall models like the images shown here. (Note: Section View used to show inside of cube.)

You can only select one face at a time when creating a Shell Feature.

To create the geometry shown in the image, where each wall has equal thickness, in the fewest number of mouse clicks, use the _____ Feature.

True or False: A Chamfer can be applied to an edge or a face.

User-created reference planes must reference the default top, left and right planes.

Which of the following is NOT a Plane Type in Onshape?

You can mirror an entire feature by selecting just one of its faces in the graphics area and specifying a plane or face to mirror about.

True or False: If the part you are designing is completely symmetric, you can complete the part by designing just half of the part and using one mirror feature.

When creating a part, if the features are created in the wrong order, you must delete the features and recreate them in the correct order.

Which of the following is NOT a type of arc in Onshape?

Reference the image shown here. Based on what you learned about design intent, is there ONLY ONE unique series of commands that can be used to create this part?

To extrude a sketch in both directions relative to the drawing plane,you must use a Blind end type.

The only way to create the Tab feature shown in the image is to start a sketch on the top face of the rectangular base.

In the image shown, what is the best way to make all of the fillets equal in size?

Which end type is best used when you want to extrude to a specified depth?

You must have a sketch drawn prior to activating the Extrude Remove feature.

True or False: You can select a planar face as the reference plane for mirroring a feature.

Which of the following icons represents the Onshape Mirror feature?

When using the Hole feature, it is only possible to create one hole.

Faces, edges, features, and loops can all be selected as entities to fillet.

When creating a Fillet, the Tangent Propagation option ensures that the Fillet is applied to all edges that are tangent to a selected edge.

When applying fillets, to include the edges tangent to the selected edge in the fillet, select the following option:

True or False: You can customize the material properties of a preset material.

Mass properties are calculated based on ___________.

Using the __________ option, you can change the state of a model back to where a particular feature or features weren`t yet created.

Which end type of an Extrude feature is used to add an equal amount of material to both sides of the sketch plane?

Which of the following ways allow you to place one sketch line, rather than a chain of lines?

Which of the following is an indicator that a sketch profile is closed?

Which type of Arc requires another entity to specify its start point?