Font size
WorksheetsAg Safety
Total questions: 49
Worksheet time: 4hrs 5mins
Select all of the following questions workers should include on a checklist for inspecting a ladder:
Are there any missing or broken rungs or steps
Are there any worn, damaged or missing feet
Has the ladder reached its end of duty date provided by the manufacturer
Is the rope on an extension ladder worn, broken or frayed
Strong, non-conductive and susceptible to weather and age all describe a ladder made of what type of material?
Wood
Fiberglass
Aluminum
Composit
Workers should never allow their center of gravity to extend beyond the rails of the ladder.
True
False
Sara is working on a scaffold and accidentally kicks a loose screwdriver. Which of the following will help prevent the screwdriver from falling to the ground?
Observe the OSHA Six Foot Rule
Top rail
Mid rail
Toe board
The OSHA Six Foot Rule states any worker under six feet in height must wear fall protection equipment.
True
False
Which of the following describes a personal fall arrest system?
A safety net installed around a scaffold or building
A harness worn around the upper body and waist, connected to a lanyard or lifeline, which is properly anchored to the building or structure
A safety belt worn around the waist with a lanyard attached to the ladder
Straps worn around the shoulders attached to the scaffold
Ladders are NOT made from which of the following materials?
Wood
Fiberglass
Composite
Aluminum
A step ladder should never be ascended past the third step from the top.
True
False
Ryan is using his ladder safety checklist and observes a ladder on the jobsite with a broken rung. Ryan should notify his supervisor and ensure no one uses the ladder.
True
False
How many points of contact should a person ascending or descending a ladder have?
1
2
3
4
According to the Occupational Safety and Health Administration (OSHA), falls from elevated surfaces are the leading cause of injury and death on construction sites.
True
False
When a straight ladder is too close to a contact surface, it strengthens the ladder's stability.
True
False
Which of the following ladders is susceptible to UV rays, is very strong and does not conduct electricity?
Wood
Fiberglass
Composite
Aluminum
Elsa is using a miter saw to cut 2 x 4 lumber. What should she use to help hold the wood in place?
Her hand
Clamps
Have another person help hold the material
Vice
How far should fingers be kept away from the blade of a band saw?
1
2
3
4
Which of the following tools are usually handheld and designed to remove material from the edge of a work piece?
Router
Planer
Jointer
Shaper
Most nail guns are equipped with a safety device, commonly called a contact safety.
True
False
A push block should be used in which of the following instances?
Anytime a hand may possibly enter too close to a moving blade
Only when working with metal
Only when working with thin material
When wearing leather gloves
When working with pneumatic tools, one should always wear appropriate eye protection
True
False
A nail can follow the grain of the wood, causing it to curve and exit where it is not intended.
True
False
Only use attachments rated for the pneumatic tool.
True
False
Always have a finger on the trigger of a pneumatic tool.
True
False
Always read the manufacturer’s instruction manual for pneumatic tools.
True
False
A band or scroll saw is used for cutting smaller pieces of materials and can cut curves.
True
False
A drill should never be operated while wearing gloves or safety glasses.
True
False
Milly is using a sliding compound miter. Where should she start the cut on the material?
Directly over the material
At the outermost point traveling forward away from the fence
At the foremost point traveling backwards toward the fence
Dependent upon the size of material being cut
A blade which is circular and wraps around two drive wheels is associated with which of the following saws?
Band saw
Scroll saw
Circular saw
Table saw
Select the correct answer from the choices provided in the underlined section. Never let go of material between the blade and the guard / fence.
guard
fence
Select all of the following elements necessary to produce a fire.
Carbon dioxide
Fuel
Heat source
Oxygen
Tools with cords having exposed wiring should only be used after the cord has been repaired using electrical tape.
True
False
Oily rags should always be left in a designated container with a tight fitting lid.
True
False
Certain metals and substances, when heated during welding processes, will produce potential toxic gasses which are released into the atmosphere.
True
False
Common sense is one of the most valuable tools when working in a shop.
True
False
GFCI stands for which of the following?
Ground Fault Circuit Interrupter
Ground First Circuit Intermitter
General Fault Circuit Interrupter
Ground Finding Circuit Inspector
Select all of the following which are common fuel for a fire in a shop.
Metal shavings
Oily rags
Paper
Sawdust
A Safety Data Sheet does NOT contains which of the following?
Instructions for using the chemical
First aid measures
If the chemical will react with other substances
How a chemical will affect the body
Electrical equipment should never be used outside or in wet conditions unless the circuit is protected by a GFCI.
True
False
How should all chemicals be stored?
In a clearly marked and approved container or cabinet
In a plastic container in the shop’s supply closet
On OSHA approved shelving
In a clear container
Eli is staining his wood project using a pneumatic sprayer. Which respiratory protection should he be wearing?
No protection is required
Cotton face mask
Respirator
N95 particulate dust mask
Students and workers should NOT perform which of the following inspections on their hard hat?
Visually inspect the shell for cracks or damage
Squeeze the hard hat to ensure it is still pliable
Ensure hearing protection is attached
Check the suspension system
Maddie is sanding a piece of wood and sawdust entered her eye from not wearing safety glasses. What should be the first thing Maddie does?
Use the eye wash station
Report the incident to her instructor
Call her family
Go to the school nurse
Hearing loss usually occurs suddenly and without warning.
True
False
There is no need to wear safety glasses and a face shield at the same time.
True
False
Long hair should always be pulled back and pinned out of the way.
True
False
When should fire resistant clothing be worn?
When moving equipment
When doing anything in the shop
When using a drill press
When welding
Select the correct answer from the choices provided in the underlined section.
Hearing protectors must be tested and approved by ANSI in accordance with OSHA / EPA.
(a)
Respirators with filter canisters can protect the lungs from harmful fumes.
True
False
NRR stands for which of the following?
Noise Replacement Rating
Noise Rejection Rating
Noise Redirecting Rating
Noise Reduction Rating
Mark is working in the wood shop. Which of the following scenarios would be a safety hazard?
Wearing a welding hood when welding
Wearing earmuffs when using a miter saw
Wearing gloves when using a drill press
Wearing a hard hat during building construction
