WorksheetsFurniture Testing 2
Total questions: 25
Worksheet time: 1hrs 20mins
What is the function of this Furniture testing Machine?
(a)
Which one of the following sharing a same furniture?
Seating | Table | Storage
Domestic & Office Furniture
Educational & Office Furniture
Non Domestic & Office Furniture
Domestic & Non Domestic Furniture
Domestic, Non Domestic, Educational & Office furniture are the list of:
Furniture Category
Furniture Type
Furniture Test
Furniture Use
EN acronym refer to?
(a)
BSEN 12520:2015 – Furniture – strength, durability and safety – requirements for domestic seating.
5.1 – All parts of the seating with which the user come into contact, during intended use, shall be designed to ensure that physical injury and damage are avoided
These requirements are met when:-
Edges of the seat, back rest and arm rests, which are in contact with the user when sitting are rounded or chamfered.
Ends of hollow components are closed or capped
Shear & squeeze point exists if the distance between two accessible parts moving relative to each other can be more than 7mm or less than 18mm in any position during movement
All other edges accessible during use shall be free from burrs and / or sharp edges;
What standards (BS EN) are involved in the testing of domestic furniture category?
Dom. furn. – seating – Test method
Furniture – seating – determination of stability
Furniture – strength, durability & safety)
Furniture – Standard Safety Specification for Chair and Stools
Which one is NOT the test type needed for Educational Chair category?
Safety
Stability
Strength & Durability
Fatigue
Base on BSEN 1022:2018. How many chair size marks are in furniture testing?
7
6
8
5
The chair size is measured from the floor surface to the point?
D
C
B
A
Other than General Requirements. What is the test needed for safety?
(a)
What types of visual images need to be captured prior to conducting a testing session?"
Component view
Standard plan view
Potential hazardous or failure parts / components
High angel/ eye level/ Low angle
Should the laboratory always be within a temperature range?
15ºC ~ 25ºC
10ºC ~ 20ºC
25ºC ~ 35ºC
5ºC ~ 20ºC
What is the recommended controlled temperature of the laboratory?
23°C
20°C
22°C
21°C
What is the name of furniture testing machine as on Figure
Seat Front Edge Durability Test Machine
Arm Sideways Test Machine
Vertical ImpactTest Machine
Arm Durability Test Machine
What is the name of furniture testing machine as on Figure
Seat Front Edge Durability Test Machine
Arm Sideways Test Machine
Vertical ImpactTest Machine
Arm Durability Test Machine
Which one is NOT the name of furniture testing machine as on Figure
Seat Front Edge Durability Test Machine
Arm Sideways Test Machine
Vertical Impact Test Machine
Arm Durability Test Machine
Which one of the test types does NOT require conducting 10x cycles?
Seat front edge durability test
Back impact test
Seat static load & back static load test
Arm rest durability test
How many cycles does the Seat Front Edge Durability test need to complete?
25,000
10
50,000
10+2
The strength & durability requirements are fulfilled when during and after testing in accordance:
There are no fractures of any member, joint or component
There are no loosening of joints intended to be rigid
Seating fulfils the stability requirements
Seating fulfils its functions after removal of the test loads
All other edges accessible during use shall be free from burrs and / or sharp edges
Identify point i, ii and iii as in figure.
i.Back Load Point
ii.Seat Load Point
iii.Point S
i.Seat Load Point
ii.Back Load Point
iii.Point S
i.Back Load Point
ii.Point S
iii.Seat Load Point
i.Point S
ii.Back Load Point
iii.Seat Load Point
Which of the following is NOT a category of furniture?
Educational
Non Domestic
Domestic
Industrial
What is the main purpose of the Arm Rest Durability Test?
To assess the durability of the arm rest
To measure the height of the chair
To check the strength of the seat
To test the stability of the furniture
According to furniture testing standards, which test is used to evaluate the stability of a chair?
Stability test
Back impact test
Seat static load test
Arm sideways test
Which test is performed to check the strength of a chair's backrest?
Arm rest durability test
Back impact test
Stability test
Seat static load test
What is the main objective of the Stability Test in furniture testing?
To measure the weight of the furniture
To ensure the furniture does not tip over easily
To assess the comfort level
To check the color fastness
