WorksheetsQuality Control quiz
Total questions: 28
Worksheet time: 22mins
How to standardize the management use of four point bending strength tester? [Four Point Bending Test]
a. Ensure instrument in stable state.
b. Ensure instrument in control state.
c. Ensure instrument in fix state.
Labor protection that is not included in this test? [Four Point Bending Test]
a. Googles
b. Hair Net
c. Uniform Cloth
d. Helmet
How does the power work for the four point bending machine ? [Four Point Bending Test]
a. Turn on the power and pull the emergency stop button.
b. Turn on the power and push the emergency stop button.
c. Turn on the power and enter the emergency stop button.
Which tools is not included in Four point bending test inspection? [Four Point Bending Test]
a. Four point bending test software.
b. Four point bending test machine.
c. Four point bending test meter.
Which operation system procedure is not included in Four Point Bending Inspection? [Four Point Bending Test]
a. Perform 0 calibrations.
c. Select 560nm wave band as the judgement area.
b. Input thickness,width,and support support distances.
During the back plane test in four point bending inspection. How many sample glass need to be prepare? [Four Point Bending Test]
a. 4 sample glass
b. 5 sample glass
c. 6 sample glass
Before testing, what is the standard height of the lower shelf in four point bending test inspection? [Four Point Bending Test]
a. 1441mm
b. 1451mm
c. 1461mm
What is the purpose for the tin surface inspection? [Tin Surface Inspection]
a. To standardize the distinction between tin and air surface of glasses
b. To standardize the type of glass that is used.
c. To standardize air surface glass.
What is the model number for the tool used? [Tin Surface Inspection]
a. TS680
b. TS580
c. TS560
Do we illuminate the tool from the top or the bottom of the glass to see results? [Tin Surface Inspection]
a. Bottom
b. Top
c. Inside
Where is the tin surface usually found? [Tin Surface Inspection]
a. Top of the glass
b. Bottom of the glass
c. The edge of the glass
How do we acknowledge if it is an air surface? [Tin Surface Inspection]
a. If the glass shows a blue-ish color
b. If there is no glow
c. If the car cannot start
How do we know if its a tin surface? [Tin Surface Inspection]
a. If there is an obvious torquise glow
b. If there is an obvious purple glow
c. If there is an obvious white glow
Which of the following statements is true? [Tin Surface Inspection]
a. If there is no glow, it is a Tin surface
b. If there is a green glow, it is an Air surface
c. If there is a white glow, it is a Tin surface
What is the main purpose of Contact Angle test ? [Contact Angle Inspection]
a. To test the Hydrophilic properties of coated glass.
b. To test the Hydrophilic & Hydrophobic properties of non-coated glass.
c. To test the Hydrophilic & Hydrophobic properties of coated glass.
What is the tools for this test ? [Contact Angle Inspection]
a. Laptop, angle instrument, usb cable
b. Vernier caliper, steel tape, usb cable
c. Angle instrument, laptop, vernier caliper
After we enter the software test, what is the next step for this test operation ? [Contact Angle Inspection]
a. Place glass retention film on testing table.
b. Turn on camera in the software & Capture detection interface.
c. Set up the instrument & connect sequentially.
One important precaution in this test ? [Contact Angle Inspection]
a. Use a long USB Cable
b. Blue line must be in the middle of the water droplet when fitting value
c. Glass must be perpendicular to the edge.
Where do you record the result for Contact Angle test ? [Contact Angle Inspection]
a. Backplane glass sampling record form.
b. Coated glass sampling record form.
c. front-plate glass sampling record form.
If there is no water in the detector, what we should do to the button ? [Contact Angle Inspection]
a. Turn clockwise
b. Turn counter clockwise
c. Do not turn
What is the average value for this test ? [Contact Angle Inspection]
a. ≤ 40°
b. ≥ 40°
c. 40°
What is the purpose of Transmissivity test? [Transmittance Inspection]
a. To measure thickness of glass
b. To measure light transmission of glass
To measure effectivity of coating.
What is the increase rate of float glass? [Transmittance Inspection]
a. 2.6%
b. 2.4%
c. 2.5%
What is the standard qualification of tempered glass? [Transmittance Inspection]
a. ≥ 90.14%
b. ≥ 94.35%
c. ≥ 91.60%
What is the standard qualification for Calendered glass, Single layered coating? [Transmittance Inspection]
a. ≥ 91.60%
b. ≥ 93.80%
c. ≥ 94.35%
What is the standard qualification for Calendered glass, Double layered coating? [Transmittance Inspection]
a. ≥ 94.15%
b. ≥ 94.35%
c. ≥ 91.60%
What is the standard qualification for Float glass? [Transmittance Inspection]
a. ≥ 94.35%
b. ≥ 91.60%
c. ≥ 94.15%
How many times do QC inspector needs to calibrate the transmittance detector machine (AOPTEK Spectral Transmittance Device) ? [Transmittance Inspection]
a. Once per year
b. Two times per shift
c. Once per day
