wayground logo

Free Printable Worksheets

Font size

S
M
L
XL
Worksheets

Construction 1 - Semester Exam Review

Total questions: 97

Worksheet time: 1hrs 15mins

Name
Class
Date
1.

Convert 144" to feet

a)

1728'

b)

12'

c)

48'

d)

432'

2.

Convert 8' 0 1/2" to inches

a)

0.70"

b)

20 1/2"

c)

96 1/2"

d)

102"

3.

What is 5' 6" + 3' 4" =

a)

8'-10"

b)

2'-2"

c)

15'-24"

d)

1'-3"

4.

Solve 23' 6' + 7' 6"

a)

30'-12"

b)

18'

c)

35'

d)

31'

5.

Double the fraction 3/16

a)

3/32

b)

6/32

c)

3/8

d)

16/3

6.

double the fraction 5 3/8

a)

10 3/4

b)

5 3/4

c)

2 3/16

d)

10 3/8

7.

What direction is considered plumb?

a)

horizontal

b)

vertical

c)

north

d)

south

8.

Cut the fraction in half 3/4

a)

1 1/2

b)

6/8

c)

3/8

d)

6/4

9.

What direction is considered level?

a)

horizontal

b)

vertical

c)

east

d)

west

10.

What tool is used to make a long layout line?

a)

tape measure

b)

level

c)

chalk line

d)

speed square

11.

Cut the fraction in half 7/8

a)

7/4

b)

7/16

c)

1 3/4

d)

3/4

12.

You need to drill a hole to hang a picture in the center of your board. Your board is 8 1/2 inches long. At what measurement should you drill your hole?

a)

17"

b)

4 1/2

c)

5"

d)

4 1/4"

13.

This is a

a)

Vice Grip

b)

Dolphin Wrench

c)

Try Square

d)

Chalk Line

14.

This is a...

a)

Channel Locks

b)

Needle Nose Wrench

c)

Adjustable

Crescent Wrench

d)

Sliding T Bevel

15.

This is a...

a)

Stair Gauge

b)

Framing Square

c)

Yard Stick

d)

Sliding T Bevel

16.
a)

Laser Level

b)

Tape Measure

c)

Try Square

d)

Speed Square

17.

This is a...

a)

Drill

b)

Impact Driver

c)

Nut Driver

d)

Wood Screw

18.

This is a...

a)

Forstner Bit

b)

Impact Driver

c)

Drill

d)

Framing Nailer

19.
a)
level
b)
combination square
c)
framing square
20.

Match the following

a)
1.

Cold Chisel

b)
2.

Wood Chisel

c)
3.

Sawzall or Saber Saw

d)
4.

Jig Saw

e)
5.

Sliding Compound Miter Saw

21.

Match the following

a)
1.

Combination Square

b)
2.

Framing Square

c)
3.

Speed or Swanson Square

d)
4.

Folding Ruler

e)
5.

Tri-Square or Tile Square

22.

Match the following

a)
1.

Adjustable Pliers or Channel Locks

b)
2.

Slip Joint Pliers

c)
3.

Needle Nose Pliers

d)
4.

Lineman Pliers

e)
5.

Locking Pliers or Vise Grips

23.

Match the following

a)
1.

Spirit Level or 2' Level

b)
2.

4' Level

c)
3.

Line Level

d)
4.

Plumb Bob

e)
5.

Laser Level

24.

Match the following

a)
1.

Combination Wranch

b)
2.

Box End Wrench

c)
3.

Ratcheting Wrench

d)
4.

Pipe Wrench

e)
5.

Adjustable or Crescent Wrench

25.

Match the following

a)
1.

Impact Driver

b)
2.

Cordless Drill

c)
3.

Circular Saw / Skill Saw

d)
4.

Framing Hammer

e)
5.

Curved Claw Hammer

26.

Check to ensure that all safety ______ and tables are in place and working correctly.

a)

nets

b)

guards

c)

chains

d)

switches

27.

Before using the Miter Saw, you should

a)

Ask instructor's permission

b)

Remove all jewelry, eliminate loose clothing, and confine long hair

c)

Wear approved sanitized safety glasses

d)

All of the above

28.

Disconnect the power ________ making any angle or blade adjustments

a)

after

b)

during

c)

before

d)

none of the above

29.

Have all cut lines clearly marked before using the Miter Saw

a)

True

b)

False

30.

Keep your fingers _________ from the cut line and blade.

a)

away

b)

under

c)

near

d)

on

31.

_____________ start the blade while it is touching the stock (material you are cutting)

a)

Do

b)

Do not

c)

All of the above

d)

None of the above

32.

After you are finished with the Miter Saw, you should:

a)

Wait for the Miter Saw to come to a complete stop

b)

Clean up all scraps and dust after the blade stops

c)

Both of these

d)

None of these

33.

What is the margin of safety for the miter saw. (minimum distance your finger's should come to the blade?)

a)

4"

b)

3"

c)

Differs from saw to saw.

d)

8"

34.

The amount of material a blade removes from the lumber when making a cut is called?

a)

Blade curve

b)

Kerf

c)

Cut waste

d)

Extracted waste

35.

What type of cut is this?

a)

Rip Cut

b)

Cross cut

c)

Miter cut

d)

Compound cut

36.

How is a miter saw sized?

a)

By the maximum size of stock which can be cut on the machine.

b)

By the horsepower rating of the motor.

c)

By the diameter of blade used on the saw.

d)

All of the above.

37.

Identify part number 1 in the picture.

a)

Blade

b)

Retractable blade guard

c)

Fence

d)

Miter Scale

38.
All table saw adjustments should be made:
a)
While the saw is in motion
b)
While the saw is completely stopped.
c)
It depends on which type of blade you're using.
d)
After the fence has been removed from the table.
39.
Use a push stick when ripping material less than ________.
a)
4" wide
b)
12" wide
c)
1" wide
d)
the fence height
40.

Identify Part A

a)

Blade Guard

b)

Table

c)

Miter Guage

d)

Elevation Hand Wheel

41.

Identify Part B

a)

Miter Gauge

b)

Power Switch

c)

Blade Guard

d)

Table

42.

Identify Part C

a)

Fence

b)

Tilt Hand Wheel

c)

Miter Gauge

d)

Blade Guard

43.

The saw blade should extend through the material being cut by ______ inches

a)

1/8

b)

1/4

c)

1/2

d)

1

44.

Material should be well supported when being cut with the portable circular saw to ______

a)

Keep it from falling over

b)

So the cut can be made quickly

c)

To prevent damaging material

d)

To prevent binding the saw blade and causing a kickback

45.

To make a long straight cut with the portable circular saw .......

a)

Clamp a guide on the material

b)

Such cuts can not be made with a portable circular saw

c)

Move the saw rapidly through the cut

d)

Move the saw slowly through the cut so it can be guided straight

46.

Before putting the saw down after a cut has been made......

a)

Unplug the saw

b)

Make sure the cover is over the blade

c)

Make sure the blade has stopped rotating

d)

All of the above

47.

The blade on the Portable Circular Saw should be aligned _______ when making a cut.

a)

On the waste side of the marking line

b)

On the marking line

c)

1/4 inch away from the marking line

d)

1/2 inch away from the marking line

48.

To make a plunge cut with the Portable Circular Saw the operator should______

a)

Uncover the blade and slowly lower the blade into the material being cut

b)

Rest the heel of the saw base on the material, uncover the blade and slowly lower the blade into the material being cut

c)

Rest the front of the saw base on the material, uncover the blade and slowly lower the blade into the material being cut

d)

Lock the into a stationary position, turn it on and raise the material into the saw blade

49.

Identify this tool.

a)

Portable Circular Saw

b)

Cordless Drill

c)

Hack Saw

d)

Circular Saw Blade

50.

Name the tool

a)

Hammer

b)

Air compressor

c)

Slip Joint pliers

d)

Locking pliers

51.

Name the tool.

a)

Felipe Screwdriver

b)

X Screwdriver

c)

Phillips Screwdriver

d)

Long Screwdriver

52.
a)
Ball Peen Hammer
b)
Wrench
c)
Claw Hammer
53.
a)
G Clamp
b)
C Clamp
c)
Bar clamp
54.
a)
Combination square
b)
try square
c)
framing square
55.

This is a..

a)

Hand Planer

b)

Flat Bar

c)

Wood Chisel

d)

Cats Paw

56.
a)

Laser Level

b)

Tape Measure

c)

Try Square

d)

Speed Square

57.

This is a...

a)

Hook Blade

b)

Belt Sander

c)

Jig Saw

d)

Sawzall

58.

This is a...

a)

Drill

b)

Impact Driver

c)

Nut Driver

d)

Wood Screw

59.

This is a...

a)

Forstner Bit

b)

Impact Driver

c)

Drill

d)

Framing Nailer

60.

What is this type of plier?

a)

Slip Joint

b)

Side Cutting

c)

Linemans

d)

Needle Nose

61.

a)

hex (Allen) wrenches

b)

angle wrenches

c)

corner bevel

d)

corner support

62.

a)

hack saw

b)

keyhole saw

c)

back saw

d)

coping saw

63.

a)

expansion bit

b)

twist bit

c)

auger bit

d)

Forsner bit

64.

a)

masonary bit

b)

power bit

c)

hole bit

d)

paddle or spade bit

65.

a)

Forsner bit

b)

countersink

c)

auger bit

d)

flare bit

66.

a)

circle saw

b)

hole saw

c)

depth saw

d)

chuck saw

67.
a)

Expansion Auger Bit

b)

Brad Point Bit

c)

Auger Bit

d)

Drill Bit

68.

When should eye protection be worn in the shop?

a)

at all times when you are in the shop area

b)

only when you are working

c)

only when you are watching someone else work

d)

only when you feel like it

69.
When should accidents be reported to the teacher?
a)
if the injury is minor, it doesn't need to be reported
b)
immediately, no matter how small
c)
at the end of class 
70.
Which of the following should never be worn around tools and machines? (a)  
Choose from the below words
jewelry and loose fitting clothing
blue jeans
sneakers 
71.

When should spills be cleaned up?

a)

immediately

b)

at the end of class

c)

when the custodian is able to clean it up

72.
No (a)   is allowed in the shop.
a)
blueprints
b)
PPE
c)
effort
d)
 horseplay 
73.

Users must ____ _______ ______  at the end of class.

a)
leave all tools
b)
leave the area
c)
clean up area
d)
None of the above
74.

Never  ________ _________ __________ equipment you have not received training on.

a)
attempt to use
b)
attempt to photograph
c)
attempt to describe
d)
attempt to oil
75.

If a machine is not working correctly:

a)

Shut it off and go to a different machine

b)

Google how to make it better

c)

Turn the music up in your ear buds

d)

Report it to the Instructor

76.

What is the correct way to hold a sharp object?

a)

With the sharp point facing downward toward the ground

b)

With the sharp point facing upward toward your body

c)

With the sharp point facing to the right

d)

With the sharp point facing to the left

77.
Use a ____________ or rag to clear away scraps and sawdust. 
a)
Brush
b)

Air Hose

c)

Hand

d)

Scrap Lumber

78.
When you are finished with a tool, return it to its assigned (a)   area. 
Choose from the below words
Electrical
Help
Storage
Damages
79.
Ask for (a)   when you need to handle large or heavy material. 
Choose from the below words
Electrical
Help
Storage
Legs
80.
Lift with your (a)   , not with your back. 
Choose from the below words
Electrical
Help
Damaged
Legs
81.
Equipment with a (a)   power cord should be reported to the instructor.  It should not be sued. 
Choose from the below words
Electrical
Help
Damaged
Legs
82.
Don't yank on the power cord to disconnect a tool.  Pull the __________________. 
a)
Guards
b)
Plug
c)
Adjustments
d)
Running
83.
Always disconnect the power equipment before you make any major _________________. 
a)
Guards
b)
Plug
c)
Adjustments
d)
Completely
84.
Never adjust equipment while it is ___________. 
a)
Plug
b)
Guards
c)
Completely
d)
Running
85.
When you turn off a machine, stay with it until it is _________ stopped. 
a)
Guards
b)
Plug
c)
Completely
d)
Running
86.
Don't __________ anyone while they are operating the equipment. 
a)
Safe
b)
Distract
c)
Play
d)
Attention
87.
Using the tools and equipment requires your complete __________ at all times. 
a)
Safe
b)
Stopped
c)
Distract
d)
Attention
88.
Never fool around or ______________ in the shop.
a)
Safe
b)
Play
c)
Distract
d)
Attention
89.

If your hair is long enough to touch your shoulders or covers your eyes, you must be___

a)

tied back

b)

cut off

c)

put under a hat

d)

"braided" by a power tool

90.

Do not leave a machine until all _____ has stopped.

a)

motion

b)

motors

c)

power

d)

dancing

91.

Make sure what is turned on before using machines?

a)

Your brain

b)

The machine

c)

Dust collector

d)

The oven

92.

If something goes wrong, what should you do?

a)

Continue like nothing happened

b)

Blame it on the nearest person

c)

Go bananas

d)

Turn everything off and get the instructor

93.

Use tools

a)

for their designated purpose only

b)

as a weapon

c)

in situations where the correct tool isnt available

d)

as needed

94.

All guards

a)

are optional

b)

are a distraction from your work

c)

must be kept in place. Under no circumstance should the guards be removed.

d)

must be kept out of the way of your work so they do not interfere.

95.

All tools used

a)

are color coded and assigned to a team.

b)

will be replaced by the last person to use it.

c)

will be returned to their proper storage area after use.

d)

will be cleaned daily.

96.

Unplug

a)

machines when in use

b)

safety switches

c)

power tools before performing maintenance, changing components or clearing jams.

d)

power tools before sweeping, changing components or clearing jams.

97.
Never  ________ ___ ____equipment you have not received training on.
a)
attempt to use
b)
attempt to photograph
c)
attempt to describe
d)
attempt to oil

Similar Resources on Wayground

RELIGION 10 - PART 1 Review

97 questions

RELIGION 10 - PART 1 Review

quiz

Worksheet

•

10th Grade

Pengetahuan agama

100 questions

Pengetahuan agama

quiz

Worksheet

•

4th - 11th Grade

Star Wars 101 - Ultimate Trivia

101 questions

Star Wars 101 - Ultimate Trivia

quiz

Worksheet

•

KG - Professional Dev...

Intro 2 Psych--re-learn

100 questions

Intro 2 Psych--re-learn

quiz

Worksheet

•

11th - 12th Grade

#IBE-YES, ICOULD!, 10º 2020

94 questions

#IBE-YES, ICOULD!, 10º 2020

quiz

Worksheet

•

10th Grade

LP UP 2

100 questions

LP UP 2

quiz

Worksheet

•

10th Grade - University

Undercarriedge 5

100 questions

Undercarriedge 5

quiz

Worksheet

•

12th Grade - University

AFNR Final Exam Spring 2020

100 questions

AFNR Final Exam Spring 2020

quiz

Worksheet

•

9th - 11th Grade