WorksheetsMaintenance Publications
Total questions: 38
Worksheet time: 19mins
(1) Propellers are NOT included in the Airworthiness
Directive system.
(2) A certificated powerplant mechanic may make a minor repair on an aluminum propeller and approve for return to service
Regarding the above statements,
Only No.2 is true
Both No.1 and No.2 are true
Neither No.1 nor No.2 is true
(1) The Federal Aviation Regulations require approval after compliance with the data of a
Supplemental Type Certificate
(2) An installation of an item manufactured in accordance with the Technical Standard Order system requires no further approval for installation in a particular aircraft
Regarding the above statements,
Only No.2 is true
Neither No.1 and No.2 is true
only no.1 is true
Type Certificate Data Sheets are issued for which of the following products?
Aircraft, engines and propellers
Aircraft, engines and appliance
Aircraft, engines, propellers and appliance
Where are technical descriptions of certificated propellers found?
Applicable Airworthiness Directives
Aircraft Specification
Propeller Type Certificate Data Sheet
(1) Manufacturer's data and FAA publications such as Airworthiness Directives, Type Certificate Data
Sheets, and advisory circulars are all approved data
(2) FAA publications such as Technical Standard Orders, Airworthiness Directives, Type Certificate Data Sheets, and Aircraft Specifications and Supplemental Type Certificates are all approved data
Regarding the above statements,
Both No. 1 and No.2 are true
Only No. 1 is true
only no. 2 is true
The following is a table of airspeed limits as given in an FAA-issued aircraft specification:
Normal-exceed speed 293 knots Maximum landing gear operation speed 174 knots
Maximum flap extended speed 139 knots
The high end of the white arc on the airspeed instrument would be
260 knots
293 knots
139 knots
Which regulation provides the airworthiness standards for an airplane certificated in the normal category?
14 CFR Part 27
14 CFR Part 25
14 CFR Part 23
Placards required on an aircraft are specified in
AC 43. 13-1B
The Federal Aviation Regulations under which the aircraft was type certificated
Aircraft Specifications or Type Certificate Data
Sheets
Aviation Maintenance Alerts (formerly General
Aviation Airworthiness Alerts)
Provide mandatory procedure to prevent or correct serious aircraft problems
Provide information about aircraft problems and suggested corrective actions
Provide temporary emergency procedures until
Airworthiness Directives can be issued
Airworthiness Directives can be issued
what is the maintenance recording responsibility of the person who complies with an Airworthiness Directive?
Advise the aircraft owner/operator of the work performed
Make an entry in the maintenance record of that equipment
Advise the FAA district of office of the work performed, by submitting an FAA Form 337
Primary responsibility for compliance with Airworthiness Directives lies with the
Aircraft owner or operator
Certificated mechanic holding an Inspection Authorization who conducts appropriate inspections
Certificated mechanic who maintains the aircraft
A Technical Standard Order (TSO) is issued by whom?
The Aircraft Industry
Part Manufacturers
The Administrator
Check trust bearing nuts for tightness on new or newly overhauled engines at the first 50-hour inspection following installation. Subsequent inspections on thrust bearing nuts will be made at each third 50-hour inspection.
From the above statement, at what intervals should you check the thrust bearing nut for tightness?
150 hours
200 hours
250 hours
A complete detailed inspection and adjustment of the valve mechanism will be made at the first 25 hours after the engine has been placed in service.
Subsequent inspections of the valve mechanism will be made each 50-hour period. From the above statement, at what intervals will valve mechanism inspections be performed?
100 hours
50 hours
125 hours
How long are AD compliance records required to be kept?
Until the work is repeated or superseded by other work
For one year after the work is performed, or until the work is repeated or superseded by other work
They shall be retained, and then transferred with the aircraft when it is solid
What does the Type Certificate Data designation code '2 PCSM' mean?
Two place (number of seats), closed, sea, monoplane.
Two wing(biplane), primary category, semimonocoque (airframe)
Neither of the other two choices.
Suitability for the use of a specific propeller with a particular engine-airplane combination can be determined by reference to what informational source?
Propeller Specifications or Propeller Type Certificate Data Sheet
Aircraft Specifications or Aircraft Type Certificate Data Sheet.
Alphabetical Index of Current Propeller Type Certificate Data Sheets, Specifications and Listings.
An aircraft Type Certificate Data Sheet contains.
Maximum fuel grade to be used
Control surface adjustment points
Location of the datum
The Air Transport Association of America (ATA)
Specification No. 100 (1) establishes a standard for the presentation of technical data in maintenance manuals.
(2) Divides the aircraft into numbered systems and simplify locating maintenance instructions.
Regarding the above statements,
Both No. 1 and No.2 are
Neither No.1 nor No.2 is true
Only no.1 is true
Which of the following includes all the regulatory
definitions of 'maintenance"?
Overhaul, repair, parts replacement, and
preservation, and preventive maintenance
Overhaul, repair, parts replacement, preservation, inspection, and preventive maintenance
Overhaul, repair, parts replacement, inspection, and preservation
(1) A Supplemental Type Certificate may be issued to more than one applicant for the same design change, providing each applicant shows compliance with the applicable airworthiness requirement.
(2) An installation of an item manufactured in accordance with the Technical Standard Order system requires no further approval for installation in a particular aircraft.
Regarding the above statements,
Both No. 1 and No.2 are true
Neither No.1 nor No.2 is true
Only No.1 is true
What is the maximum penalty for cheating or other unauthorized conduct when taking an FAA mechanic test?
Ineligibility to receive any certificate or rating for one year
Ineligibility to receive any certificate or rating for one year, and suspension or revocation of any certificate held
Ineligibility to receive any certificate or rating for one year, and suspension of any certificate held
Which regulation provides information regarding instrument range markings for an airplane certificated in the normal category?
14 CFR Part 21
14 CFR Part 25
14 CFR Part 23
what information is generally contained in Aircraft
Specifications or Type Certificate Data Sheets?
Empty weight of the aircraft
Useful load of aircraft
Control surface movements
The action required by an AD may take what form?
1. Inspection
2. Part(s) replacement
3. Design modification
4. Change in operating procedure(s)
5. Overall change in the content, firm and disposition of the aircraft maintenance records.
1,2,3,4
1,2,3,5
1,2,3,4,5
Airworthiness Directives are issued primarily to
Provide information about malfunction or defect trends
Present recommended maintenance procedures for correcting potentially hazardous defects
Correct an unsafe condition
Specifications pertaining to an aircraft model manufactured under a type certificate, of which less than 50 are shown on the FAA Aircraft Registry, can be found in the
Aircraft listing
Summary of Discontinued Aircraft
Specifications
FAA Statistical Handbook of Civil Aircraft
Specifications
The following words are an example of what kind of statement in an AD? 'Required within the next 25 hours time-in-service after the effective date of this
AD, unless already accomplished
Amendent
Compliance
Applicability
Under the Federal Aviation Regulations, an Aviation maintenance technician is required to perform maintenance on an aircraft so that it
Always meets its original type design
Is at least equal to its original or properly altered condition
Exceeds minimum standards with regard to aerodynamic function, structural strength, resistance to vibration, and other qualities affecting airworthiness
When is a mechanic responsible for checking AD compliance?
Never, the owner or operator is solely responsible
When performing an inspection required under part 91, 125, or 135
Anytime an aircraft or portion thereof is returned to service
When information is generally contained in Aircraft Specifications or Type Certificate Data Sheets?
Empty weight of the aircraft
Useful load of aircraft
Control surface movements
The issuance of an Airworthiness Certificate is governed by
14 CFR Part 23
14 CFR Part 21
14 CFR Part 39
An aircraft mechanic is privileged to perform major alterations on U.S. certificated aircraft; however, the work must be done in accordance with FAA-approved technical data before the aircraft can be returned to service. Which is NOT approved data?
Airworthiness Directives
AC 43. 13-24
Supplemental Type Certificates
. Technical information about older aircraft models, of which no more than 50 remain in service, can be found in the
Aircraft Listing
Summary of Deleted and Discontinued Aircraft Specifications
Index of Antique Aircraft
Where are technical descriptions of certificated propellers found?
Applicable Airworthiness Directives
Aircraft specifications
Propeller type Certificate Data Sheets
The Air Transport Association of America (ATA)
Specification No. 100
(1) Establishes a standard for the representation of technical data in maintenance manuals
(2) Divides the aircraft into numbered systems and subsystems in order to simplify locating maintenance instructions
Regarding the above statements,
Both No. 1 and No. 2 are correct
Neither No.1 nor No.2 is correct
Only No. 1 is correct
Which of the following are sometimes used as authorization to deviate from an aircraft's original type design?
1. FAA Form 337
2. Supplemental Type Certificate
3. Airworthiness Directives
4. Technical Standard Order
1,2,3,4
1,2,4
1,2,3
When an airworthy (at the time of sale) aircraft is sold, the Airworthiness Certificate
becomes invalid until the aircraft is reinspected and approved for return to service
is voided and a new Certificate is issued upon application by the new certificate is issued upon application by the new owner
is transferred with the aircraft
