Identify the symbol:

Identify the symbol:

Identify symbol:

Identify symbol labeled M1:

_________________________ drawings show physical details of an object as seen by the eye.

A____________________ diagram shows the connection of all components within a piece of equipment.

A __________ diagram looks like rungs on a ladder and shows the relationship between circuits and components.

Identify the symbol:

Identify the symbol:

The 5S organization system is a workplace organizational system that stands for sort, straighten, sweep or shine, standardize, and ___.

Sharp-edged and pointed tools should be carried with the cutting edge or point ___ and away from the body.

Power tools should be inspected and serviced by a qualified repair person at regular intervals as specified by the ___ or by OSHA.

All power tools should be grounded unless they are an approved ___ design.

Always check for the presence of ___ before taking any measurements.

A ___ tester is a test instrument that tests for a complete path for current to flow.

A ___ tester is a device that is plugged into a standard receptacle to determine if the receptacle is properly wired and energized.

A ___ tester is a device that indicates approximate voltage level and type (AC or DC) by the movement and vibration of a pointer on a scale.

A(n) ___ is a meter that can measure two or more electrical properties and displays the measured properties along calibrated scales using a pointer.

A(n) ___ is a meter that measures the current in a circuit by measuring the strength of the magnetic field around a single conductor.

___ voltages are produced by the magnetic fields generated by current-carrying conductors, fluorescent lighting, and operating electrical equipment.

A(n) ___ is a test instrument that provides a visual display of voltages.

A(n) ___ is a device that detects insulation deterioration by measuring high resistance values under high test voltage conditions.

A(n) ___ is a device used to measure ground connection resistance of electrical installations such as power plants, industrial plants, high-tension towers, and lightning arrestors.

No more than ___ load(s) should be placed in any circuit line between the power lines L1 and L2.

Two loads must not be connected in ___ in one line of a line diagram.

A ___ is the electrical device in a line diagram that uses the electrical power from L1 to L2.

The load is ___ all the time if no control device is included in a line.

The dashed line method works well when the control contacts are close together and the circuit is relatively ___.

All circuits are composed of ___ basic section(s).

___ is not a signal condition.

The ___ accomplishes no work by itself; it merely starts or stops the flow of current in that part of the circuit.

In most cases it is the operating coil in the circuit that is responsible for initiating the ___.

___ diagrams are one of the oldest and most common methods of illustrating and understanding basic logic functions.

___ logic is used in industry when two NO pushbuttons are connected in series to control a solenoid.

___ logic is used in industry when an NO pushbutton and an NO temperature switch are connected in parallel.

___ logic has an output if the control signal is OFF.

___ logic is an extension of NOT logic in which two or more NC contacts in series are used to control a load.

___ logic is an extension of NOT logic in which two or more NC contacts are connected in parallel to control a load.

___ circuits are also known as holding or sealing circuits.

An example of a(n) ___ process is a standard light switch that has only two positions: fully ON or fully OFF.

Additional stop pushbuttons are connected in series using ___ logic with the existing stop pushbuttons.

Additional start pushbuttons are connected in parallel using ___ logic with the existing start pushbuttons.

___ logic is used in a circuit when a pilot light is used to show that an operation has stopped.

___ is the frequent starting and stopping of a motor for short periods of time.

___ is the systematic elimination of various parts of a system, circuit, or process to locate a malfunctioning part.

A(n) ___ circuit is an electrical circuit that has an incomplete path that prevents current flow.

A switch in the OFF position is a(n) ___ circuit.

A(n) ___ circuit is a circuit in which current takes a shortcut around the normal path of current flow.

A(n) ___ short is a short circuit that opens the circuit as soon as the circuit is energized or when the section of the circuit containing the short is energized.

A ___ is a device that controls one electrical circuit by opening and closing contacts in another circuit.

A(n) ___ relay is a switching device that has sets of contacts that are closed by a magnetic effect.

A ___ relay is a mechanical switch operated by a magnetic coil.

___ relays are designed for commercial and industrial applications where economy and fast replacement are high priorities.