NEW
Font size
WorksheetsWoods I Final Review
Total questions: 36
Worksheet time: 18mins
What kind of cuts are made with a bandsaw?
Crosscuts
Rip cuts
Curved cuts
Any cuts you want
What kind of cuts are made with a table saw?
Crosscuts
Rip cuts
Curved cuts
Any cuts you want
What kind of cuts are made with a miter saw?
Crosscuts
Rip cuts
Curved cuts
Any cuts you want
Where should the guard be positioned on the bandsaw?
Up to 1/4" above the stokc
Up to 1/8" above the stock
Up to 1/2" above the stock
Up to 1" above the stock
What is the purpose of relief cuts?
They are special cuts for softwood
They are special cuts for hardwood
They prevent the blade from binding
The are quick, rough cuts
When is it safe to put your hand in line with the blade of the bandsaw?
When your hand is at least 4" from the blade
When your hand is at least 2" from the blade
When your hand is at least 6" from the blade
When the machine is off
What do you do if you need to back out of a cut on the bandsaw?
Leave the power on, so it comes out smoothly
Leave the power on, but reduce the blade speed
Leave the power on and loosen the blade tension
Turn the power off and wait for the blade to stop
How should the miter saw be held after the cut is finished but before the blade stops moving?
The down position
Raised 1" above the cut stock
The up position
Pull the saw all the way out
Hands should never be closer than _____ inches to the blade when using the miter saw
2
4
6
8
Where should the saw blade be aligned when making a cut on the miter saw?
On the right side of the line
On the left side of the line
On the waste side of the line
On the marking line
How should the saw blade be moved through the stock when making a cut with the motorized miter saw that has a sliding arm?
Pull out then push down
Push straight down, then adjust the piece
Pull out, push down, then push forward
Push down, then pull out
Painted wood can be sanded on the belt and disc sander
True
False
Which of the following would NOT be safe practice when using the table saw?
Securing a helper to support the material being sawed
Pushing the material through the table saw with a push stick
Standing in line with the saw blade
Using a blade guard
When making a cut with the table saw, the saw blade should extend no more than __ inches above the stock being cut
3/8"
1/4"
1/2"
1/8"
What kind of stock CANNOT be cut with a table saw?
Square stock
Round stock
Flat stock
Thick stock
What is the purpose of an off-bearer in a table saw operation?
Remove scraps, support, and help pull stock through the table saw
Support the stock as it is pushed through the saw
Pull the stock through the saw
Support and pull the stock through the saw
What is the maximum cut recommended for the thickness planer?
1/32"
1/16"
1/8"
1/4"
What should you do if the lumber being planed gets stuck part way through the cut?
Stop the planer, remove, then discard the board
Stop the planer, wait until the cutter head stops, then readjust the planer
Lower the table to free the stock and keep cutting
Panic and run awway
How should lumber be fed into the planer?
With the grain
Against the grain
On edge
Only with the operator standing within 18" of the planer
Where should the bit be placed when starting a cut with the router?
Not in contact with the stock
Slightly tilted to make starting easier
In place and ready to start cutting as it turns on
Elevated to make it easier to see
Which of the following is NOT a safety precaution when using the router?
Disconnect the power before changing bits
Wearing safety glasses
Using a bit with a pilot ened
Holding the router with both hands
Which part of the wood should be cut with the router first to prevent splintering on the corner of wood?
Middle section
End grain
Left side
Right side
Which of the following is the correct procedure for holding the router while making a cut?
Hold the handle with one hand and guide the router with the other hand
Hold the handle with one hand and put the other hand on the motor housing
Hold on to the stock with pressure on the cutter bit side
Hold the router firmly with both hands
Is pine a softwood or hardwood?
Softwood
Hardwood
Is oak a softwood or hardwood?
Softwood
Hardwood
Is poplar a softwood or hardwood?
Softwood
Hardwood
Is alder a softwood or hardwood?
Softwood
Hardwood
What type of screw should be used with pine?
Fine
Coarse
What type of screw should be used with oak?
Fine
Coarse
What type of screw should be used with alder?
Fine
Coarse
What type of screw should be used with poplar?
Fine
Coarse
What is the purpose of sanding wood?
To create a smooth surface finish
To cut a piece of wood in half
To add color to the wood
To hide mistakes
Which grit of sandpaper would give you the roughest finish?
180
120
100
80
Which product listed would you use if you wanted to seal and protect wood?
Oil-based stain
Water-based stain
Polyurethane
Gel stain
Which of the following would you use if you wanted to change the color of the wood grain?
Stain
Oil
Varnish
Sand paper
Which direction of sanding will give a smoother finish?
Across the grain
In circles
With the grain
It doesn't actually matter
