wayground logo

Free Printable Worksheets

NEW

Font size

S
M
L
XL
Worksheets

IMI REVISION LEVEL2

Total questions: 64

Worksheet time: 21mins

Name
Class
Date
1.

What does the diagram illustrate about a 'Single point' system?

a)

It shows the point of air intake only.

b)

It illustrates the connection between fuel, air, and the engine control unit (ECU) in a system.

c)

It depicts a cooling system for electronic components.

d)

It represents a hydraulic system.

2.

What does SPI stand for in the context of fuel injection systems?

a)

Single Point Injection

b)

Systematic Point Interface

c)

Single Pressure Injection

d)

Systematic Pressure Increase

3.

What is the fuel supply pressure for a Single Point Injection system?

a)

2 bar

b)

1 bar

c)

0.5 bar

d)

1.5 bar

4.

What is the primary function of an ECU (Electronic Control Unit) in automotive systems?

a)

To play music through the car's audio system

b)

To control the vehicle's electronic systems by processing input signals and sending output signals

c)

To monitor the car's fuel levels only

d)

To enhance the vehicle's external appearance

5.

The definition of the term 'castor angle' is defined as

a)

inclination of the road wheel relative to the vertical axis, when viewed from the side of the vehicle

b)

angle of the road wheel steering axis relative to the vertical, as viewed from above the vehicle

c)

angle of the road wheel steering axis relative to the vertical, as viewed from the side of the vehicle

d)

inclination of the road wheel relative to the vertical axis, when viewed from the front of the vehicle

6.

During traction control operation

a)

the brake is rapidly applied and released on the spinning wheel until traction is regained

b)

the brake is applied on the non spinning wheel until traction is regained

c)

the brake is applied on the spinning wheel until traction is regained

d)

the brake is rapidly applied and released on the non spinning wheel until traction is regained

7.

When cornering, a vehicle with electronically controlled air suspension will,

a)

immediately provide more air pressure to the air springs on the outside of the bend

b)

provide more air pressure to the air springs on the outside of the bend after a short delay

c)

immediately provide more air pressure to the air springs on the inside of the bend

d)

provide more air pressure to the air springs on the inside of the bend after a short delay

8.

One advantage of a vehicle fitted with EPAS over a vehicle fitted with hydraulic power steering is

a)

less steering effort

b)

no torque sensing required

c)

reduced steering rack ratio

d)

improved fuel economy

9.

During hard braking, an insecure load in the boot will slide forward due to

a)

Normal force

b)

gravitational force

c)

inertia force

d)

centrifugal force

10.

On a hybrid vehicle, which one of the following is responsible for the amount of regenerative braking required?

a)

The main brake pedal switch

b)

The ABS modulator valves

c)

Master cylinder pressure sensor

d)

All four wheel speed sensors

11.

What does a central door locking actuator contain?

a)

Solenoid and rocker switch

b)

Drive motor and gear

c)

Motor and solenoid

d)

Solenoid and gear

12.

What is the name of the electrical principle, that is used to stop the wiper system against momentum, once the wipers has been switched off?

a)

Regenerative braking

b)

Electromotive force

c)

Electromagnetic induction

d)

Reactive braking

13.

The device shown is more commonly know as

a)

a logic gate

b)

a transistor

c)

a solenoid switch

d)

an intergrated circuit (IC)

14.

How is the compressor clutch engaged on an air conditioning system?

a)

Using a solenoid

b)

Using Permanet magnets

c)

Electromagnetically

d)

Mechanically using gears

15.

What should the resistance reading of a door contact switch be, when the door is closed?

a)

Infinity

b)

0 Ohms

c)

100 Ohms

d)

10K ohms

16.

What are the main advantages of using LED lighting

a)

They produce a bright blue light from 1 LED

b)

Quick reaction and greater reliability

c)

Quick reaction and greater reliability

d)

Slow reaction time increasing life expectancy

17.

On a typical vehicle heater system, a customer complains of loss of slowspeeds of the motor. What would be the most likely fault?

a)

Resistor pack failure

b)

Coolant sensor faulty

c)

Switch faulty unit

d)

Motor brush failure

18.

When checking an electric window or mirror, what should be checked first?

a)

Fuse

b)

Switch

c)

wiring

d)

Motor

19.

In relation to cooling and air conditioning, what is meant by the term convection?

a)

Transfer of heat using waves or particles

b)

The difference in air pressure

c)

Transfer of heat which involves a fluid

d)

Flow of heat through a material

20.

On a SRS system with an Airbag and Seatbelt Pre-tensioner, what will be occurring from 10-15 milliseconds after impact?

a)

Driver hits the bag and the pre-tensioner releases

b)

Impact identified and pre-tensioner ignition

c)

Airbag is inflated and the pre-tensioning is complete

d)

Airbag starts to inflate and pre-tensioner moving

21.

What would the symptom be, if the system earth failed on an electric window circuit?

a)

Window would opeerate slowly

b)

Window would not operate

c)

Window would only do down

d)

Window would only go up

22.

What does PWM stand for?

a)

pulse width modulation

b)

primary wired modules

c)

Pulse weighted motors

d)

Pulse wired motors

23.

How many motors are used in a typical single electric mirror adjusting system?

a)

1

b)

2

c)

3

d)

0

24.

which one of the following terms applies to the reflector part of a headlight?

a)

Prism

b)

lense

c)

Parabolic

d)

condenser

25.

What are the symptoms likely to be the next time the engine is started if the alternator charge warning lamp has blown?

a)

The alternator will overcharge

b)

The alternator will only charge at idle

c)

The alternator will only charge at high revs

d)

The alternator will not charge

26.

The pattern shown on an oscilloscope of an hall effect type sensor would be a

a)

Square wave

b)

cosine wave

c)

saw tooth

d)

Sine Wave

27.

How does an ABS system with an inductive wheel speed sensors know that a wheel is slowing down?

a)

an decreasing D.C. voltage

b)

an increasing D.C. voltage

c)

an decreasing A.C. voltage

d)

an increasing A.C. voltage

28.

the diagram represents a wave form from an inductive speed sensor. What will happen to the sine wave as the component rotates faster?

a)

Voltage remains the same and the frequency increases

b)

Voltage increases and the frequency increases

c)

Voltage increases and the frequency remains the same

d)

voltage remains the same and the frequency remains the same

29.

What is an electronic device that lets electronic current flow only 1 way

a)

zener diode

b)

capacitor

c)

Transistor

d)

Rectifier

30.

Your Satellite Navigation system is struggling to locate your position. the most likely cause is

a)

a faulty yaw angle sensor

b)

a faulty wheel speed sensor

c)

only 2 satellites are in view of the receiver

d)

only 3 satellites are in view of the receiver

31.

What will be the effect of a lamp with a poor earth connection?

a)

Lamp will be dim

b)

Circuit fuse will blow

c)

the bulb will blow

d)

lamp will be brighter

32.

An ohms test on a Thermister indicates 0C=4500 ohms 100C 200 ohms this type of thermister is

a)

negative temperature coefficient

b)

positive temperature coefficient

c)

exponential temperature coefficient

d)

reverse temperature coefficient

33.

The pattern shown on an oscilloscope of an inductive type sensor would be a

a)

square wave

b)

cosine wave

c)

saw tooth

d)

sine wave

34.

The function of the low pressure switch in an air conditioning system is to

a)

regulate refrigerant flow when the system is switched on

b)

increase air flow through the condenser when required

c)

disconnect the compressor due to low gas/liquid level

d)

reduce evaporator temperature when required

35.

What is a multiplex network?

a)

a data bus system carrying signals to and from remote control units

b)

more wiring than conventional automotive wiring systems

c)

a data bus system carrying battery voltage to and from remote control units

d)

a data bus system carrying AC signals to and from remote control units

36.

What readings would be expected when checking the feed to the terminals on a front heated screen?

a)

Within 0.5v of the battery voltage

b)

Within 1.75V of the battery voltage

c)

Within 2.5v of the battery voltage

d)

Within 4.6v of the battery voltage

37.

What is the correct procedure to check for a parasitic drain

a)

Ignition off, disconnect both battery leads and connect an ammeter in parallel

b)

Ignition off, disconnect the battery earth and connect an ammeter in series

c)

Ignition off, disconnect the battery positive and connect a voltmeter on series

d)

Ignition on, disconnect both battery positive and connect an ohmmeter in series

38.

A diesel glow plug is suspected to be faulty. The test to be carried out would be

a)

an amperage check with an ohmmeter

b)

a switching check with an oscilloscope

c)

a voltage check with an ohmmeter

d)

a resistance test with an ohmmeter

39.

What on a car uses a sun load sensor?

a)

Climate control system

b)

Central door locking

c)

A car alarm

d)

An electric window

40.

A gas discharge bulb contains what

a)

electrodes, argon, silver and metal salts

b)

electrodes, xenon, mercury and metal salts

c)

wire elements, helium gas and metal salts

d)

a tungsten electrode, silver and metal salts

41.

What does Flemings left hand rule relate too?

a)

Flemings right hand rule is used with motors

b)

Flemings left hand rule is used with generators

c)

Flemings left hand rule is used with motors

d)

Flemings left hand rule is used with ohms law

42.

On a hybrid electric vehicle, regenerative braking is when the

a)

generator acts as a motor

b)

brake fluid recuperates

c)

parking brake is slowly applied

d)

motor acts as a generator

43.

Which of the following statements is correct?

a)

1 Hertz = 1 cycle per second

b)

Hertz is the unit of magnetic flux

c)

The unit of power is the Hertz

d)

1 Hertz = 360 degrees rotation

44.

When checking for parasitic drain, the voltmeter is connected in parrallel with the battery and all consumers are switch on

a)

True

b)

False

45.

A strain gauge pressure sensor incorporates the use of

a)

magnetic induction

b)

a thermister

c)

sensing resistors

d)

piezo crystals

46.

Which of the following is NOT true about LEDs?

a)

LEDs have a shorter operating life than conventional bulbs

b)

LEDs can produce a brighter light than conventional bulbs

c)

LEDs can operate quicker than conventional bulbs

d)

LEDs are vibration resistant

47.

What is the operating temperature of an incandescent bulb?

a)

2000 degrees celcius

b)

2300 degrees celcius

c)

1500 degrees celcius

d)

3000 degrees celcius

48.

What does DRL stand for?

a)

Daylight running lamps

b)

Daytime running lights

c)

Digital resonance lighting

d)

Digital running lighting

49.

When discussing engine temperature sensors, what does NTC stand for?

a)

Negative temperature coolant

b)

Negative temperature coefficient

c)

Numbered temperature coolant

d)

Numbered temperature current

50.

What sensor is used for automatic headlight systems?

a)

Thermistor

b)

Photo cell

c)

Inductive

d)

Hall effect

51.

In modern, heavy commercial vehicles, what is the most common use for LED lighting?

a)

Side marker lights

b)

Headlight low beam

c)

Front driving lights

d)

Front fog lights

52.

Directional indicators should flash at which rate?

a)

40 to 100 flashes per minute

b)

60 to 120 flashes per minute

c)

95 to 125 flashes per minute

d)

90 to 140 flashes per minute

53.

How many wires are normally connected to a twin filament light bulb?

a)

1

b)

2

c)

3

d)

4

54.

Identify the circuit the item shown belongs to.

a)

The indicator circuit

b)

The headlamp circuit

c)

The spot light circuit

d)

The reverse lamp circuit

55.

What does PWM stand for?

a)

Pressure width modulation

b)

Pulse width modulation

c)

Pulse wave modulation

d)

Pressure wave modulation

56.

Where is the reverse light switch normally mounted?

a)

Instrument panel

b)

Transmission

c)

Brake pedal arm

d)

None of the above

57.

How many brushes does a two-speed wiper motor have?

a)

1

b)

2

c)

3

d)

4

58.

Where is the stoplight switch normally mounted?

a)

Instrument panel

b)

Transmission

c)

Brake pedal arm

d)

None of the above

59.

A gas discharge bulb contains what?

a)

A tungsten electrode, silver and metal salts

b)

Wire elements, helium gas and metal salts

c)

Electrodes, argon, silver and metal salts

d)

Electrodes, xenon, mercury and metal salts

60.

What is the reflective part of a headlamp called?

a)

A prism

b)

A parabolic

c)

A lens

d)

A condenser

61.

What is the part below used for?

a)

Stop light operation

b)

Airbag control

c)

Interior lamp circuits

d)

Side light operation

62.

Which of the following components is essential for the operation of a piezoelectric sensor?

a)

Capacitor

b)

Resistor

c)

Piezoelectric crystal

d)

Inductor

63.

What is the primary function of a thermistor in an electronic circuit?

a)

To store electrical energy

b)

To measure temperature

c)

To amplify signals

d)

To convert AC to DC

64.

Which type of sensor is commonly used to detect the rotational speed of a wheel?

a)

Thermistor

b)

Inductive sensor

c)

Capacitive sensor

d)

Photoelectric sensor