WorksheetsCarpentry EOPA Part 2
Total questions: 53
Worksheet time: 27mins
Complete the following statement with the BEST choice.
To calculate the pitch of a roof one must divide the ____________by the ____________
Rise, run
Slope, length
Run, rise
Length, slope
What is the primary purpose of following industry standards during the installation of wood shingles and miter corners?
To jeopardize project quality
To ensure long term performance
To ignore best practices
To delay projection completion
Plans call for 12’ pilasters, in the corners and at third points around the perimeter of the foundation of the structure measuring 91’ x 85’. What are the measurements center line to centerline between the pilasters on the short and long sides?
26’ & 28’
27’4” & 29’4”
28’4” & 30’4”
28’ & 30’
The International Residential Code (IRC) requires a step to be no greater than 7 ¾" with a tread depth of no less than 10”. What are the minimum number of treads and the minimum length of the stairway that is 10’6” from floor to floor?
15 treads, 12’6”
16 treads, 13’4”
14 treads, 11’8”
12 treads, 10’
What type of saw is BEST to cut moldings?
Circular saw
Chain saw
A power or hand miter saw
Snips
Every opening must have a support on how many sides?
3
4
2
2 or 3
In high wind areas, how often should hurricanes ties be installed, tying the rafter to the double top plates?
At every rafter
24 inches on center
48 inches on center
72 inches on center
Which softwood is often used for window frames, door jamb and exterior trim in residential construction?
Hemlock
Douglas Fir
White Pine
Cedar
Complete the following statement with the BEST choice.
Roof sheathing should always be _______________ row to row
Taped
Water-proofed
Staggered
Nailed
What is a typical use of cherry hardwood in residential construction?
Roof trussed
Exterior decking
Interior cabinetry and furniture
Basement insulation
Complete the following statement with the BEST choice.
Shop built or manufactured forms shall be ____________ to enable reuse.
Handled
Cleaned
Discarded
Both handle and cleaned
Toe boards must be used on work platforms when working over what height?
4 ft
6 ft
8 ft
10 ft
Which of the following is typically NOT used as a benchmark in construction projects?
Permanent survey monuments
Manholes or utility access points
GPS coordinates
Temporary stakes or flags
With single 2X trimmers on each side of a rough opening, how much longer should a header be built for the rough opening size?
¾"
1 ½"
2 ½"
3"
A rafter with a 6 in 12 pitch in said to have a slope what?
6 run 12 rise
0.75
0.5
72
What is the minimum width of a stairwell with one handrail?
27"
30"
32"
36"
When setting up a Builder's Level on concrete, what methods ensure the base doesn't move?
Setting up on plywood
Duct Tape, Tape Measure
Decking boards on top of concrete
Thick cardboard or triangular wood base
Complete the following statement with the BEST choice
Before framing roof openings for dormers, rafters or joist need to be ________ for__________
checked, capacity
modified, openings
marked, slope
aligned, windows
Which factor should guide the installation process of gypsum board?
Personal Preference
Social Media posts
Costing savings
Project plans
Why is it important to follow blueprints when installing gypsum board?
So proper fire ratings are maintained where they are required
To decrease project complexity
To reduce waste
To reduce project costs
Complete the following statement with the BEST choice.
The simplest method to lay out a rafter is to step off the layout in ________ increments.
1"
6"
equal
1 foot
What is a common application of teak hardwood in residential construction?
Window frames
Interior paneling
Decking and outdoor furniture
Attic insulation
When installing crown molding or other trims, what type of tool is used to measure?
Tape Measure
Folding Ruler
Square
Yard Stick
In a window schedule, what does the abbreviation "W x H" typically represent?
Window Width x Height
Water Header
Window Hardware
Wall Height
What is the maximum gap between a grinding wheel and tool rest on a bench grinder?
0"
1/16"
1/8"
3/16
What is the maximum deflection of a floor joist be (in inches) when installing ceramic tile?
L in inches/120
L in inches/180
L in inches/240
L in inches/360
The plans call for support columns to be no more than 12' center to center, equally spaced, in each direction. How many columns and piers are required on a project whose dimensions are 64' x 44'?
35
32
36
38
Complete the following statement with the BEST choice.
Sheath on a roof should always have ______ bearing on a rafter or joist at each end.
at least equal
full
partial
3/8"
What direction should a joist crown be installed?
With the crown up
With the crown down
With the crown to the right
With the crown to the left
When laying out a foundation all measurements originate from which of the following?
Using your laser level
The benchmark
Using batterboards
The property line
Which type of molding is typically installed horizontally on the wall surface, dividing it into upper and lower sections?
Baseboards
Chair rail
Crown molding
Casing
What is the primary reason for following manufacturer recommendations during siding installation?
To decrease projection completion
To overlook quality control
to ensure product durability and comply with product warranties
To reduce project costs
If the exterior walls are 24" apart and are 10' high, what are the rise and run of the roof if the peak is 16"
6/12
10/24
12/6
10/12
Use the Pythagorean theorem to calculate the diagonal distance between opposite corners to determine the squareness of a footing with dimensions 120' x 160'
220 feet
210 feet
230 feet
200 feet
Complete the following statement with the BEST choice.
The width of any ______ should be added to calculate the length of the rafter
sheathing
firestops
overhang
soffit boards
What is the maximum height of the work surface when using ladder jacks?
12 ft
16 ft
20 ft
25 ft
Complete the following statement with the BEST choice.
Nails, stakes and ties shall be removed from forms ______
When sorting
When directed
For safety
Prior to reuse
What is a common use of cedar softwood in residential construction?
Roof sheathing
Interior paneling
Exterior siding and trim
Flooring
What type of defect in lumber is characterized by irregularly shaped cavities or holes caused by insects?
Checks
Wane
Decayed
Insect Damage
What does the abbreviation "OC" commonly stand for"
Overhang Clearance
On Center
Outer Corner
Off Cut
What is the first step in ensuring that a window frame is installed correctly according to the project blueprint and manufacturer's standardd?
Check the rough opening for correct dimensions and levelness before installation
Install the window sash into the frame to ensure it fits before securing the frame
Immediately secure the frame with nails to the rough opening
Apply caulking around the perimeter of the opening before placing the frame
What is the recommended tolerance when installing corner boards, moldings or metal/vinyl corners?
1/4"
1/8"
1/2"
1'
What is the minimum ratio of a cantilevered floor joist?
1 FT of Cantilevered per 2 FT of Backspan
1 FT of Cantilevered per 3 FT of Backspan
1 FT of Cantilevered per 4 FT of Backspan
1 FT of Cantilevered per 5 FT of Backspan
When installing folding doors, why is it most important to follow industry and manufacturers' and standards?
To ensure proper closure
To ensure there is enough room for door operation
To create eye appeal within the project
All answer choices are correct
If the exterior walls of a house are 32' apart and are 12' high, what are the rise and run of the roof if peak is 18"
12/16
6/16
16/6
12/32
Which of the following is NOT typically found in drawing notes and specifications?
Material requirements
Tolerances
Geometric dimensioning and tolerancing
Engineering calculations
Which type of drawing view would be most helpful in determining the thickness of a wall in a building?
Plan view
Elevation view
Section view
Isometric view
What is the PRIMARY purpose of measuring, cutting and installing gypsum board?
To cause delays in the construction project
To experiment with various methods of installation
To ensure the product is installed correctly and meets the codes
To help create short cuts, saving time
When constructing a built-in, where can one find specified sizes, shapes and finishes?
Builders can use personal judgment for these elements, so they are not specified anywhere
Written on the drywall for where the built-in will be placed
Project blueprints or plans
Owners decide these elements, SO the builder should leave them unfinished
When installing accessories, how should the carpenter find their intended locations?
. By looking on the accessory box
Accessories do not have intended locations
By watching a video on the topic By watching a video on the topic
By viewing project blueprints or plans
How much should end joints be offset between rows when installing subfloor or roof decking?
16 inches
19.2 inches
32 inches
48 inches
According to the manufacturer's recommendations, when should adhesive NOT be used before installing a subfloor over wood joists?
With crawlspace applications
With basement applications
With slab on grade applications
When installing subfloor in attic spaces
To lay out a common rafter, what roof measurement does one need to know
Pitch
Rise
Run
Area
