NEW
Font size
WorksheetsWarm Air Systems Quiz
Total questions: 30
Worksheet time: 15mins
What is one advantage of warm air systems over wet central heating systems?
They require more maintenance.
They start delivering warm air quickly.
They are more expensive to install.
They need a special type of radiator.
What was a characteristic of early warm air installations in the 1960s and 1970s?
They were intended as full house central heating.
They had warm air outlets only on upper storeys.
They relied on natural convection to transfer heat.
They were commonly used in commercial buildings.
What is a feature of later warm air system installations?
They only use open-flues.
They can be upflow, downflow, or horizontal flow units.
They are only installed in new buildings.
They require manual operation.
What happens in conventional warm air systems when the heat exchanger reaches a predetermined temperature?
The fan shuts down immediately.
The burner will cycle on and off.
The system will switch to manual mode.
The air supply is cut off.
What is the function of the overhead thermostat in the heat exchanger system?
To increase the fan speed
To reset the system manually
To interrupt the supply to the gas valve
To adjust the room temperature
What is the purpose of a positive return air path in installations from the late 1970s onwards?
To increase the temperature of the heat exchanger
To prevent the room from becoming de-pressurised
To reduce the speed of the fan
To block air circulation through bathrooms
How does the fan differential thermostat in thermistor-based systems differ from older models?
It uses a manual control board
It requires frequent resetting
It is replaced by thermistors and an electronic control board
It operates at a higher temperature
What is the primary design feature of "slot-fit" appliances?
Access from the back only
Access from the sides only
Access from the front only
Access from all sides
What should be considered when designing duct layouts?
The color of the ducts
The size and layout of the building
The material of the ducts
The brand of the ducts
What is a common solution for replacing ageing warm air units?
Using larger appliances
Using modern heat engines
Using older models
Using electric heaters
What is a possible cause if little or no heat is emitted at registers?
Gas rate incorrect
Cracked heat exchanger
Blocked return air filter
Incorrectly set thermostat
Which technique is recommended for inspecting difficult areas of a heat exchanger?
Use a smoke pellet
Use a mirror
Use a powerful torch
Use a flue brush
What should be checked when the fan is operated during a heat exchanger inspection?
Gas valve assembly
Flame disturbance
Drive belt alignment
Circulation filter
According to the document, what should be done if the heat exchanger has split?
Replace the fan
Replace the heat exchanger
Clean the burner
Adjust the gas input
What is a sign that the heat exchanger may be cracked or corroded?
Smoke from the burner
Distorted flames when the fan starts
Gas leaks
Corrosion on the baffle
What should a registered engineer check before servicing a warm air heater?
The color of the heater
The installation complies with Standards and Manufacturers instructions
The age of the heater
The size of the heater
What is one method to inspect a warm air unit heat exchanger for cracks?
Listening for unusual sounds
Visual inspection using light
Checking the temperature
Measuring the airflow
What does a flame disturbance indicate during the inspection of a warm air unit?
A malfunctioning fan
A cracked heat exchanger
A blocked air filter
A faulty thermostat
What is the purpose of the smoke test in inspecting a warm air unit?
To check the color of the smoke
To detect a cracked heat exchanger
To measure the smoke temperature
To test the smoke alarm
What is a common issue with older warm air systems?
They are too energy efficient
They often have cracked heat exchangers
They are only suitable for small buildings
They require no maintenance
What is the role of a bypass damper in a warm air system?
To cool down the system
To regulate the airflow
To increase the air pressure
To block the return air path
What should be done if a warm air system's fan is not operating correctly?
Replace the entire system
Check the fan motor and wiring
Increase the gas input
Ignore the issue
What is a common indicator of a malfunctioning heat exchanger in a warm air unit?
Increased energy efficiency
Visible soot accumulation
Lower air pressure
Unusual noise from the ducts
What should be done if a warm air unit's burner fails to ignite?
Replace the heat exchanger
Check the gas supply
Clean the air filter
Increase the thermostat setting
What is the role of a limit switch in a warm air heating system?
To regulate the gas flow
To control the fan speed
To adjust the room temperature
To shut off the burner if the system overheats
What should be done if the burner flame is unstable during operation?
Clean the air filter
Increase the thermostat setting
Check the gas pressure and adjust if necessary
Replace the heat exchanger
What is a potential consequence of a blocked return air filter in a warm air system?
Increased energy efficiency
Reduced airflow and overheating
Lower gas consumption
Improved air quality
What maintenance task should be performed regularly to ensure efficient operation of a warm air unit?
Ignore the issue
Replace the entire system
Inspect and clean the air filters
Increase the gas input
What is a potential cause of unusual noise coming from a warm air unit?
Blocked air filter
High gas pressure
Loose fan belt
Cracked heat exchanger
What is a common maintenance task for ensuring the longevity of a warm air unit?
Inspect and clean the burner assembly
Replace the heat exchanger annually
Regularly lubricate the fan motor
Increase the gas input periodically
