WorksheetsIET Onsite Guide Quiz RJH
Total questions: 30
Worksheet time: 30mins
Name
Class
Date
1.
What is the primary purpose of an RCD?
a)
Prevent electrical fires
b)
Protect against electrocution
c)
Reduce energy consumption
d)
Increase circuit capacity
2.
Which type of cable is typically used in domestic installations?
a)
Mineral Insulated Copper Cable (MICC)
b)
Twin and Earth
c)
Steel-Wire Armored (SWA)
d)
High Voltage Cable
3.
What should be considered first when designing a circuit?
a)
Insulation resistance
b)
Maximum demand and diversity
c)
Earthing conductor size
d)
Overvoltage protection
4.
What is the purpose of a main protective bonding conductor?
a)
To increase circuit efficiency
b)
To connect all exposed-conductive-parts to the main earthing terminal
c)
To insulate the main supply
d)
To isolate the installation from fault current
5.
Which is the correct earthing arrangement for most UK domestic installations?
a)
TT system
b)
IT system
c)
TN-C-S system
d)
TN-S system
6.
What is the minimum cross-sectional area of a main bonding conductor in a typical domestic installation?
a)
2.5 mm²
b)
4 mm²
c)
6 mm²
d)
10 mm²
7.
Which type of protective device is most suited for lighting circuits?
a)
RCBO
b)
RCD
c)
MCB
d)
Fuse link
8.
What is the maximum permissible voltage drop for a lighting circuit?
a)
0.03
b)
0.05
c)
0.08
d)
0.1
9.
What factor is considered when choosing a cable size?
a)
Expected life span
b)
Installation cost
c)
Current-carrying capacity
d)
Protective device brand
10.
What document certifies the compliance of a new electrical installation?
a)
Part P Certificate
b)
Electrical Installation Certificate
c)
Building Regulation Certificate
d)
Periodic Inspection Report
11.
What should be tested first during an inspection?
a)
Continuity of protective conductors
b)
Insulation resistance
c)
Polarity of the circuit
d)
Earth fault loop impedance
12.
What does an insulation resistance test check for?
a)
Circuit continuity
b)
Adequacy of bonding
c)
Faulty wiring or insulation breakdown
d)
Correct polarity
13.
In Zone 1 of a bathroom, what is the minimum IP rating required for electrical equipment?
a)
IPX2
b)
IPX4
c)
IPX5
d)
IPX7
14.
What is the main safety concern for electrical installations in agricultural buildings?
a)
Dust accumulation
b)
Corrosive gases
c)
Moisture and mechanical damage
d)
High voltage requirements
15.
What is required when installing socket outlets in outdoor environments?
a)
IP54 protection
b)
RCD protection
c)
Surge arresters
d)
Heat-resistant cabling
16.
What is the minimum disconnection time for a circuit with a final protective device not exceeding 32 A in a TN system?
a)
0.1 seconds
b)
0.4 seconds
c)
1 second
d)
2 seconds
17.
How often should a portable appliance test (PAT) be conducted for electrical equipment in an office?
a)
Monthly
b)
Annually
c)
Every 3 years
d)
Every 5 years
18.
Overload protection is provided by which device?
a)
RCD
b)
MCB
c)
RCBO
d)
Earthing conductor
19.
What is the purpose of a polarity test during inspection?
a)
To check circuit continuity
b)
To ensure correct connections of live, neutral, and earth
c)
To verify insulation resistance
d)
To determine earth fault loop impedance
20.
At what voltage should an insulation resistance test typically be performed for a 230 V circuit?
a)
230 V
b)
250 V
c)
500 V
d)
1000 V
21.
What is the primary purpose of an earth fault loop impedance test?
a)
Measure the continuity of conductors
b)
Test the insulation of the circuit
c)
Verify disconnection times of protective devices
d)
Assess voltage drop
22.
When calculating a circuit’s design current (Ib), which factor is essential?
a)
Supply frequency
b)
Power rating of connected equipment
c)
Distance to the distribution board
d)
The material of the cable insulation
23.
What is the main purpose of diversity factors in circuit design?
a)
Reduce circuit testing times
b)
Allow for reduced conductor sizes
c)
Account for simultaneous use of multiple loads
d)
Reduce the cost of installation
24.
What should be checked to ensure compliance when selecting a protective device for a circuit?
a)
The device’s appearance
b)
The cost of the device
c)
The device’s breaking capacity
d)
The voltage of the device’s coil
25.
What special consideration is required for electrical installations in swimming pools?
a)
IP ratings for equipment in wet areas
b)
Additional lighting circuits
c)
Over-voltage protection
d)
Use of twin and earth cables
26.
For circuits supplying equipment in marinas, what safety requirement is mandatory?
a)
Double insulation
b)
Use of armored cable only
c)
RCD protection with 30 mA sensitivity
d)
Use of halogen-free cables
27.
Which of the following offers protection against both overload and residual current?
a)
RCBO
b)
RCD
c)
MCB
d)
Fuse
28.
In a TT system, what component ensures the installation operates safely?
a)
Metal-clad cable
b)
Earth electrode
c)
Fuse link
d)
Surge arrester
29.
What is the required sensitivity for an RCD providing additional protection?
a)
10 mA
b)
30 mA
c)
50 mA
d)
100 mA
30.
When should a surge protective device (SPD) be installed in an electrical installation?
a)
Only in domestic installations
b)
If there is a risk of transient overvoltages
c)
To replace RCDs in high-voltage circuits
d)
When the installation supplies outdoor equipment
100 %
