Used as a terminal of the soil branch in each floor?

Always located near the stairs for use by firemen in case of fire?

It considers the building density in the locality and flammability of the structures and its content.

A vertical pipe usually used for the storage of water frequently under pressure.

Minimum of number of water closet required at Office 20 persons for employee use?

Minimum of number of water closet required at elementary school for 35 females?

When a backflow prevention device does not bear a critical level marking, the part of the device that shall constitute the critical level is the ____.

Disposal of sewage, or other liquid waste shall be by means of ____.

Roofs, inner courts, vent shafts, light wells or similar areas having drains shall discharge to (a) ____.

The organization, office, or individual responsible for enforcing the requirements of a code or standard is the ____.

A mechanical device used to circulate hot water to the plumbing system?

Used on a smaller distribution system 6 m or less for elevating water wells or other sources.

It is inserted into the water main and it serves as the control of the water service.

Piping, fixtures or equipment that are installed so that they interfere with normal operation and use of windows or doors shall be ____.

The valve for controlling two or more outlet in a cold water supply line may be a?

Refers to the pressure range measured over a period of 24 hours.

Air pressure in drainage pipes greater than atmospheric pressure.

Refers to an individual who worked in the sanitary field of ancient Rome.

It shall be the minimum cross-sectional area at the seat of the control valve or the supply pipe or tubing which feeds the device or outlet.

Airgap less than 25 mm shall only be approved as a permanent part of a listed assembly that has been tested under actual backflow conditions with vacuums of from?

Upright position, has a minimum of 150 mm or listed distance above all downstream piping and flood level rim of receptor as a function of device assembly.

As a function, it requires 30.5 cm minimum clearance at bottom for maintenance. May need platform/ladder for test and repair. May discharge water.

As a function it requires 30.5 cm minimum clearance at bottom for maintenance. May need platform/ladder for test and repair. Does not discharge water.

A general requirement, where access and clearance shall require minimum of ____ space between the lowest portion of the assembly and the grade, floor or platform.

An approved atmospheric vacuum breaker is installed not less than ____ above the flood level rim of such trapped fixture, so that at no time will any such device be subjected to any backpressure.

Water closet and urinal tanks shall be equipped with a listed ball cock shall be installed with the critical level at least ____ above the full opening of the overflow pipe.

Water closet flushometer tanks shall be protected against backflow by an approved ____ device or method.

Water supply inlets not protected by atmospheric vacuum breakers shall be protected by approved.

Potable water outlet with hose attachments other than water heater drains and clothes washer connections shall be protected by a listed or by a listed atmospheric vacuum breaker.

A device that shall not be located in any area containing fumes that are toxic, poisonous and corrosive.

Where a grounding system, acceptable to the AA is installed, inspected and approved metallic pipe may be replaced with?

Elevated or gravity tank vent shall be screened with a fine corrosion-resistant screen with openings not less than.

In water distribution system, it shall be installed on the water heating system in an approved location based on its listing requirements and the manufacturer’s instructions.

In water piping, it shall provide equivalent protection and application is restricted to those short pipe lengths at point of connection with fittings necessarily stripped fro threading and jointing.

Unions shall be installed in the water supply piping within away from regulating equipment, water heater, conditioning tank and similar equipment.

No water filter, water softener, backflow prevention device or similar devices regulated by this Code shall be installed in any potable water supply piping when the diameter of the inlet and/or outlet of nay device or its connecting pipings are less than the diameter of the water supply distribution piping.

In water piping, it shall not compress, distort cut or abrade the piping and shall allow free movement of pipe.

It shall be tightly fastened with corrosive resistant fasteners up to the floor with top surface ¼ inch (6.4 mm) above finish floor.

It shall be installed at all changes in direction as tees and bends, change in size as reducers, stops as a dead ends and valves.

The result estimating continuous supply demands in LPS for lawn sprinklers, air conditioners, etc, and add the sum to the total demand for fixtures.

In WSFU, the weights for maximum separate demands may be taken as of the listed demand for the supply.

In sizing water supply system, velocities shall not exceed of the maximum values given in the appropriate installation standard.

Hot water piping system over shall be provided with backflow preventer designed to operate without rendering any portion of the assembly inoperative.

PEX tubing shall be installed not less than from the water heater.

A pipe installed to vent, a fixture trap and which connects with the vent system above the fixture served or terminates in the open air.

Trap size of fixtures for Wash basin.

Trap size of fixtures for slop sinks (ordinary).

Minimum cost. Least efficient subject to clogging, noisy. Simple washout and emptying through small irregular passage way, prohibited by some health codes.

Trap size of fixtures for Urinals (through).

Includes water supply and distribution pipe; plumbing fixture and traps, soil, waste and vent pipes; house drain and house sewers including their respective connections.

Trap size of fixtures for Water closets.

Ratio of water closets for female population for elementary and secondary school.

A valve which in the water flow is shut off by a flat disk that is screwed down onto its seat.

The luminous flux density incident on a surface.

A short length of pipe with threads at each end; used to join couplings or fittings.

Trap size of fixtures for Sinks (Dishwashers).

A pipe connecting upward from a soil and waste stack to a vent stack for the purpose of preventing pressure changes in the stack.

Trap size of fixtures for Drinking Fountain.

A trench containing course aggregate and a distribution tile pipe through which septic tank effluent may flow covered with earth.

Trap size of fixtures for Combination Fixture.

Color coding of high pressure steam.

A passage under a road, embankment or canal which allow for the flow of water.

Is the backflow of used, contaminated or polluted water from a plumbing fixture due to negative pressure.

Is the lowest portion of the inside of any pipe or conduit that is not vertical.

An underground structure for drainage into which water from the roof or floor will drain through sewer.

An underground tank reservoir to store water.

Ratio of water closets for female population for principal worship places.

Noisy but highly efficient. Strong jet into leg forces contents out. Higher pressure required.

A U-shaped pipe filled with water and located beneath the plumbing fixtures to form a seal against the passages of gases and odors.

Trap size of fixtures for Fountain cupsiders.

Fitting for base or soil stack and building drain.

The length along the center of the pipe and fitting.

Trap size of fixtures for Floor drain.

Moderately noisy. Similar to siphon jet except that rap passageway and water surface area are smaller.

Trap size of fixtures for Laundry trays.

It is permitted that a branch soil or waste pipe to which two and more than 8 water closets, pedestal urinals, trap standard slop sinks, or shower stall are connected in a series.

A short internally-threaded (female thread) section of pipe, used to join two pipes of conduits.

A vent connecting at the junction of two fixture drains and serving as a vent for both fixtures a single vent that ventilates multiple raps, in the case of back to back fixture.

The third kind of water after the storm water and area water.

Quiet, extremely sanitary. Like the siphon jet but having the flushing water directed through the rim to create a vortex that scours the bowl.

Piping which shall not be installed under or within 2 ft (0.6m) at any building or structure is?

The extension of a soil or waste stack above the highest horizontal drain connected to the stack horizontal drain, the uppermost end above the roof.

A branch vent that serves two or more traps and extends from in front of the last fixture connection of a horizontal branch to the vent stack.

Ratio of water closets for male population for elementary and secondary school.

A pipe fitting within the interconnection of pipes for the purpose of easy dismantling of the connection when needed.

Service drop conductor clearance over the roof.

A device that discharge a predetermined volume of water to fixture for flushing purposes and is activated by direct water pressure.

Trap size of fixtures for Bathfoot.

The principal artery of the venting system to which vent branches maybe connected.

Wet standpipe for a riser not more than 15 m.

A flange that closes the end of a pipe used to discharge water.

Minimum height of dry standpipe outlet from the floor line.

Trap size of fixtures for urinals (up).

A branch vents that performs its functions for two or more traps.

Trap size of fixtures for Sinks (kitchen or residence).

A horizontal vent connecting one or more individual vents with a vent stack and stack vent.

Minimum height of Fire Service Connection from the grade/floor.

Refers to any group of two or more similar adjacent fixtures which discharge into a common horizontal waste or soil branch.

Is a pipe connecting several fixtures.

A valve which maintains uniform pressure on its outlet side regardless of its pressure fluctuation on the inlet side above the pressure level.

Used to connect the two ends pipes, neither of which can be turned.

Ratio of lavatory to number of occupants.

Maximum height of Fire Service Connection from grade/floor.

A flange that is not drilled.

The type of bathtub other than sunken, square, free standing.

A type of fitting for yoke vent.

Another classification of storm drain, besides from inside drain and outside drain.

Is a device located at the bottom of the tank for the purpose of flushing water closets and similar fixtures.

Is the extended portion of a pipe that is closed at one end to which no connections are made on the extended portion.

Install to be able to meet the water requirements during peak demands from a low yielding water well.

Process of flushing, cleaning to remove dirt by the flowing liquid through it.

Ratio of urinals for elementary schools.

Trap size of fixtures for Urinal (stall).

Trap size of fixtures for slop sinks (with combine trap).

Trap size of fixtures for Urinals (pedestal).

An arrangement of venting so installed that one vent pipe will serve two traps.

Trap size of fixtures for pantry or bar.

A vent that does not serve as drain and is located where it is not exposed to back up of waste from a drainage pipe.

Color coding for fuel oil division.

Trap size of fixtures for bath Shower stall.

Trap size of fixtures for Bidet.

Minimum discharge pipe and fitting for bathtub.

Wet standpipe for riser more than 15 m.

Sanitary, efficient very quiet. A toilet bowl which the flushing water enters through the rim and siphonic action initiated by a water jet draws the contents of the bowl through the trap way.

Dry standpipe for a riser below 23 m.

It is a pipe on the fixture side of the trap through which vapor or foul air is removed from a room fixture.

Tap used to measure pressure in a water system.

The lowest portion of the inside top surface of the channel through trap.

Water which undergoes treatment, either physical, biological or chemical means to improve water quality.

A bathroom containing a water closet and a lavatory.

How many gallons of water for the water closet flushing requirements?

Flushing is very noisy, expensive and has a low water usage (1.5 gpf) that helps conserve water. Large water surface makes this model efficient and design features make it suitable for residential use.

A vent connecting at the junction of two fixture drains and serving as a vent for both fixtures.

How can you differentiate between soil pipe and waste pipe when laid side by side.

It is added to water to reduce salinity.