WorksheetsShop Safety Exam Practice
Total questions: 39
Worksheet time: 20mins
A center punch is used to scribe a line
True
False
The ______ must be removed before turning on the switch.
Drill bit
Chuck key
Cord
Plug
You should ease up on the pressure just before the drill begins to break through the material to prevent
splitting the backside of the board
damage done to the drill bit
drilling into the tabletop
all of the above
It is okay to stop the revolving spindle of the drill with your hands
as long as the switch is off
if the cord is disconnected
never
Spring back is the tendency of the bent flange to return back a small amount
True
False
What is the maximum thickness mild steel that can be bent in the bending brake?
12 Gauge
14 Gauge
16 Gauge
18 Gauge
The Hold down (stripper) must be in ____________ position when punching a hole
the up
any
the up or down
the down
Which roller is adjusted to achieve the desired bend?
Upper Press Roll
Lower Press Roll
None of these
Idle Roll
Which roller(s) is adjusted for the thickness of the material being inserted.
Upper Press Roll
Lower Press Roll
None. They automatically Adjust
Which roller is adjusted for the thickness of the material being inserted.
Bottom Roller
Rear Roller
None. They automatically Adjust
Both Bottom Roller, and Rear Roller
Which roller is adjusted to achieve the desired bend?
Bottom Roller
Rear Roller
None. They automatically Adjust
Both Bottom Roller, and Rear Roller
What is the maximum gauge mild steel that can be rolled in a Slip Roller Machine?
16 Gauge
18 Gauge
20 Gauge
22 Gauge
During drilling operations the work must be firmly held by _____.
a drill chuck
a machine vice
your hand
a bench vice
As the drill breaks through the bottom side of your work, you should ____ the pressure on the feed lever.
increase
decrease
adjust
The upper saw guides should be set no more than ______ inch above the stock being cut.
1/2
3/4
1
1/4
It is important to keep your hands well clear of the blade and never allow your hands to pass ______ the blade.
behind
under
in front
none of the above
It is extremely important to ease up on the _____ of the stock when completing a cut on the band saw.
feed pressure
blade
table
edge
The maximum combined material thickness the portable spot welder can handle is?
1/4”
1/8”
1/16”
1/32”
The portable spot weld can only weld the following material.
steel
bronze
aluminum
copper
The maximum amount of weld time allowed is________ seconds
10
15
5
20
The spot welding machine works by a combination of _______.
sheet metal and electrodes
heat, pressure, and time
pressure and temperature
heat and spark
When scribing a line on a piece of sheet metal, color the area with _______ before scratching the line with the scratch awl.
paint
dry erase marker
a permanent marker
chalk
The bench vice is used to _______the metal sheet firmly during shaping operations.
cut
bend
hold
break
Mallets are soft hammers made of _______.
plastic
wood
rubber
all of the above
The blade must not extend more than __________ inch above the stock being cut.
3/4
1/4
1/16
1/2
The stock must be kept against the fence until __________.
the machine is turned off
the machine comes to a complete stop
it is clear of the blade
it falls off the table
“Tailing off” means ______.
using a helper to holdup the end of a long piece of stock while it is ripped
to hold your work so it will not “tail” or
vibrate
the scrap piece that has been cut off
the ripped end of the board
When crosscutting stock, always use the ______.
rip fence
hold-down foot
miter gauge
thickness gauge
You should use a push stick when running the table saw to _______.
rip short and narrow pieces of stock
adjust the stock
turn on the power
remove scraps
The operator must stand _____ so that he/she will not be in the way of the stock in the case of a “kick back.”
in front of the saw
directly behind the saw blade
slightly to the side of the saw
beside the saw
Breathing fumes of thinners is beneficial to your health and mind.
True
False
Both lock-off button and the power switch must pressed at the same time in order to start the saw
True
False
When operating the miter saw, one hand is used to press the power switch and the other hand must be at least _____ inches away from the blade
1
4
2
6
The only materials allowed to be cut on the power shear are
sheet metal and plastic
sheet metal and plastic
sheet metal and sheet aluminum
wood and plastic
The maximum thickness the sheet metal power shear can handle is
10 Gauge
14 Gauge
12 Gauge
16 Gauge
Your foot must be completely removed from the pedal box after completing each cut
True
False
Wearing gloves can be dangerous when working around machine tools.
True
False
Files are used to _______the sheet metal.
Finish
Rough
Cut
Bend
Paint fumes may explode or cause a serious fire if ignited.
True
False
