Font size
WorksheetsTable IV study guide
Total questions: 132
Worksheet time: 1hrs 9mins
Table IV Tangos M98A4 tractor is used to...
Transport Patriot Missiile System.
Serve as an ally.
Roll, cross roll, and azimuth.
Enhance launcher electronic system.
What DA form is used for patriot launcher location and alignment data(surveyed site)?
DA form 7617.
DA form 9887.
DA form M903.
DA form 7167.
(IAW) the TC 3-01.86 during what table does the LS crew members conduct RFA drills?
Table II.
Table III.
Table I
Table IV
What Patriot Gunnery table do individual crew members learn to PMCS their equipment?
Table I.
Table II.
Table IV.
Table III.
What is the minimum area required to conduct GMT missiile reload?
20x25 m
25x20 m
29x29 cm
25x27
The M860A1 flatbed semitrailer is designed to be towed by a ....?
10 ton, 8x8, tractor truck M983.
Pac 2 and Pac 3.
10 ton, 8x9, HEMTT M983A4.
Launcher Missiile Round Distributer.
What are the two methods of missiile reload?
Centralized.
Decentralized.
Mobilized.
Industrialized.
What is the official nomenclature of the A1?
ELES.
ECS.
PMCS.
LMRD.
TRUE OR FALSE? During battery table II is when crew members are introduced to missiile reload, prior to taking the table IV exam.
False.
True.
What table does LS crew members demonstrate how to manually emplace the LS using the technical manuals?
Table II.
Table I.
Table III.
Table IV.
At temperatures below 40 degrees F, the 15Kw Gen set master switch must be set to preheat for....?
30 seconds.
40 seconds.
5 minutes.
35 seconds.
What position must the elevation actuator drive motor be set to in order to hand crack the platform up or down?
Relese.
Local.
Roate.
Road-march.
For launcher SINGARS to communicate with the ECS, what are the following settings?
16,000 CT Freq hop.
17,000 CT Freq hop.
25,000 CT Freq hop.
6,000 CT Freq hop.
What are the three GMT reload configurations that can be used for missiile reload?
Parallel.
Perpendicular.
End-to-end.
Diagonal.
Counter clock wise.
When preforming TEST launch procedures on an M903 Launching station, which ports does the operator connect the umbilical cables to the JBOX?
J13 AND J15.
J19 AND J16.
J14 AND J15.
B09 AND A09.
TRUE OR FALSE? The forks should not extend more that 6 inches past the edge of the GM canister when being placed on the LS.
TRUE.
FALSE.
On a M903 LS, how many PAC3 MSE and PAC3 munitions can be uploaded as a MIX load?
PAC 3 2 cans, PAC 3 MSE 3 pair cans.
PAC 2 2 cans, PAC 3 MSE 4 cans.
PAC 3 4 cans, PAC 3 MSE 4 pair cans.
Approximately how long does it take ECS to take control of the LS once it is placed in remote?
1 min delay.
30 second delay.
10 min delay.
5 min delay.
What is the max slope after leveling and raising the LS?
+/- 5 degrees.
+/- 2 degrees.
+/- 3 degrees.
+/- 20 degrees.
The M985E1 cargo vehicle is used for?
Loading, unloading, and transport of patriot missiiles.
Preparing launching station.
Transporting additional mechanical parts for HEMMET.
When filling out the Launcher Location, Alignment Data during manual emplacement on a surveyed site, what will the "BRNG NREF TO LS" entry always be?
3,200 mils.
5,000 mils.
2,500 mils
3,000 mils.
the oil pressure indicator gauge on the MEP 814A/B GEN set should read between ......... and ........ PSI after the allotted five minute warm-up.
25- 60 psi.
60-120 psi.
85 to 90 psi,
60 to 180 psi.
The length of the MSE torque wrench extension is?
34 inch extension.
25 inch extension.
39 inch extension.
33 inch extension.
What TM is used for PMCS in the M2 aiming circle?
TM 9–60 6–70 5–2 62–10.
TM 30–60 70–6 5–2 32 –1
TM 9–30 70 –6–9 –.
Ground rods must be driven to a minimum depth of .......... to provide an effective ground.
8 feet.
9 feet.
25 feet.
6 feet.
What is the minimum safe distance to evacuate if a GM is struck or dropped more than 12 inches?
1,250 feet.(381 m)
12,000 feet.(3,657 m)
1,360 feet.(414m)
1,700 feet.(518 m)
What must be verified on the digital processor display? Dig.
LSDLU – DP, bank and address.
verify Stow and MCU off.
"ALL SWITCHES OFF".
PAC 2 and PAC 3.
On the Digital Processor, the A2A4 computer select switch must be set to......?
Front.
Back.
Rear.
Local.
What provides synchronization and timing signals for the VHF radio, and fiber Optic Links?
Digital processor.
Processor fault indicator.
Fiber optic cable assembly.
MRCTS.
Torque wrenches, will have a legible ........ , reflecting a calibration data within tolerance.
DA label 80.
DA label 75
DA label 09.
DA label 83
the Pac2 family of interceptors must be guarded to their target via the radar set. Both the PAC3 and MSE family use a seeker located within the radome. What band does the seeker operate on?
Ka-Band.
K9-Band.
PAC3 LS
PAC2 K2-Band.
Prior to hoisting, lifting or moving back to interceptors, what is the critical step operators must be verified on the canister prior to hoisting, lifting or moving?
Torque tube is in lock position.
Torque tube is in local position.
Torque tube is in rotate position.
Torque tube is in road-March position.
What are the distance for RL1 and RL3?
RL1 120m – 1.3km, RL3 6km – 30km.
RL1 130cm- 1.30 km, RL3 12 km- 50km.
RL1 180km-200km, RL3 7km-30km.
TRUE OR FALSE? Operating outriggers in diagonal pairs can twist the semi trailer frame?
TRUE.
FALSE.
What is the denied occupancy zones of the RS?(front, back, and sides.)
(a)
Excluding a potential NMC fault of the hydraulic system, how often must a load test be performed on either the GMT or forklift?
Annually.
Weekly.
Monthly.
Yearly.
TRUE OR FALSE? Wood runner(s) (skids) with cracks over 5 inches long, that extend completely through runners are unserviceable.
TRUE.
FALSE.
When troubleshooting an INFS NO-GO, which circuit breaker on the DLTM should be checked?
Maps.
ECS.
Digital processor.
Ka-Band.
How many PMP screens are on the ELES interface?
8
9
5
12
what explosive placards must be placed at the LS berm with PAC2 interceptors?
1.1E
1.3C
2.5A
1.2E
What explosive placards must be placed at the LS berm with PAC3 interceptors?
1.3C
1.1E
2.5A
1.2C
When performing before PMCS on the LS Gen, you must leave the oil dipstick in the oil dipstick tube after wiping it clean to take oil level reading for at least......
5 seconds.
10 seconds.
6 seconds.
3 seconds.
when missiiles are loaded onto LS platform, only exercise, elevation actuators, ............ times an hour with at least blank ............ minute break in between.
4 cycles within 1 hour, 3 minute breaks.
12 cycles within 3 hours, 4 minute breaks.
3 cycles within 4 hours, 1 minute breaks.
4 cycles within 2 hours, 3 minute breaks.
Who plays the LS into remote during emplacement?
CM1
CM2
Tag 1
Tag 2
What three pieces of information does the INFS give the ECS?
Roll.
Cross roll.
Azimuth.
Digital barcode.
When the HIAB 144F crane is fully retracted at 10'2", what is the maximum weight the crane can hold/move?
54,000
200,000lbs.
150,000lbs.
115,200lbs.
IAW TM 9–1440–2600–10 approximately how long does the PBIT take to complete when energizing the ELES?
30 seconds.
20 seconds.
10 seconds.
15 seconds.
What is the elevation degree of the M903 launching station?
38°
25°
70°
35°
what is the normal operating coolant temperature for the M983 A4 HEMMTT?
180–200 Fahrenheit.
200–375 Fahrenheit.
90–120 Fahrenheit.
15-100 Fahrenheit.
on the M983A4, TACHOMETER is inoperative or indicates less than ........ RPM or more than ......... RPM at idle after engine has been properly warmed up.
625 to 725 RPM
182 200 RPM
375 to 725 RPM
122 to 235 RPM
The tractor wheels must be chalked before driver leaves cab. What kind of hazard is this?
Warning(personal injury can be prevented by warning)
Hazard(could potentially personnel or equipment)
Danger.( injury to personnel or equipment.)
Life-threatening.
What drill number covers PAC 2 emplacement?
44 – CW – D0130
34-CC-D0170
43-CW-D0130
44-CW-D0120
Prepare for movement for the PAC 2, how long do you have to complete the drill?
25 minutes.
30 minutes.
45 minutes.
20 minutes.
According to 44 – CW – D0200 list in number sequence the power down steps of the DLTM – PDU.
1. Processor fault IND
2. DGTL processor.
3. SBU.
4. PWR supply.
5. Radio.
6. Blower.
7. MAPS.
8. MAPS (AEE).
9. LAMPS.
1. Radio.
2. Power.
3. SVUD
4. DGTL processor.
5. Processor fault IND.
6. Blower.
7. MAPS
8. MAPS (AEE).
9. LAMPS.
1. LAMP
2. MAPS space AEE.
3. MAP
4. Blower.
5. Processor fault IND.
6. DGTL process error.
7. SVUD.
8. Power.
9. Radio.
When draining the fuel/water separator keep the tube open until only ....... is flowing out of the drain tube.
Pure/clear fuel
Drain completely.
When the water is still murky.
When a class III leak develops.
When conducting before PMCS on the M983A4, what will cause the driver side air springs to be in NMC?
Ball valves have crack or damage that would prevent normal operations.
Everything is MCR.
ECS is not responding.
Not enough gas.
During normal operation, what should the battery gauge read for the M983A4 HEMTT?
25 vdc to 30 vdc.
15 vdc 220 vdc.
35 vdc to 60 vdc.
90 vdc to 95 vdc.
you are running a BITE test on the PAC 2 LS, the BITE test for the PAC 2 LS should cycle on and off for at least ........ seconds?
6 seconds.
12 seconds.
9 seconds.
4 seconds.
What does the acronym LMRD stand for?
Launcher missiile round distributor.
Launcher mileage round direction.
Level mile road distance.
Launcher missiile round drill.
in accordance with TM 9–2 320–3 40–10, what type of air leak deadlines a M983A4 HEMTT?
Any air leak
Small air leak
Medium air leak
2 inch air leak
What does the acronym FOCA stand for?
Fiber optic cable assembly.
Fiber optic cable assessment.
Fill over capacity acquired.
Fuel on cross roll area.
TRUE OF FALSE? Each launch enable/disable switch is set to disable to prevent inadvertent launch command signals from the ECS when electrical power is applied.
TRUE, (if the switch is set to disable then the muscles cannot be misfired.)
FALSE,(If the switch is set to enable then the missiile cannot be misfired.)
What does the acronym MRCTS stand for?
Missiile round cable test set
Missiile ready cable test set
Mileage ready connect test service
Mile ready code table service.
Ungrounded explosives are potential source of danger from static electricity. The GMT and LS must be grounded at all times and loaded with tactical GMs. What safety hazard is this considered?
Warning.
Hazard.
Safety.
Caution.
When testing the engine brake, you must push in the throttle pedal and increase engine speed to between
......... and .......... RPM.
1652 10 2100
17,000 to 18,000
1700 to 1750
100 to 200
According to TC 3–01.86, what basic gunnery table do you first conduct missiile reload?
Table III
Table II
Table I
Table IV
how high should the front outriggers be off the ground before performing a jerk test?
Just clear of the ground.
Knee level.
5 inches off the ground.
You don't remove them from the ground.
A
According to the M860 technical manual, what makes the fifth wheel kingpin mounting plate non-mission capable
Mounting plate cracked or broken
Perfectly fine
All materials intact
Equipment is MC.
The proper procedure for exercising the M860 trailer outriggers, how many times does the operator need to move it up and down weekly for PMCS?
Once a week
Once a year
Twice a week
Once every three days
What does the acronym ELES stand for?
Enhanced launcher electronic system.
Electronic launcher equipment set.
Enhance level electronic system.
eye level equipment system.
The launcher rear (back blast) area is ........ meters directly behind the launcher, and the area must be clear at all times of personnel and equipment.
90 m
20 m
120 m
100 m
If one of the missiile hazard lights come on a live missiile is present with GM cable connected at location as indicated by a light, what are the immediate actions?
Contact commander.
Notify the ECS.
Place launcher in local.
Evacuate the area.
Reload missiile as fast as possible.
The tilt warning system on the GMT (the model we currently use) will sound at what degrees?
+/-7(this is the only GMT model they are referring to not the OLD model.)
+/-6(this is the only GMT model they are referring to not the OLD model.)
+/-5(this is the only GMT model they are referring to not the OLD model.)
+/-10(this is the only GMT model they are referring to not the OLD model.)
What drill number covers PAC3 emplacement?
44 – CW – D0190
43 – CW – D01900
42 – CW – D0190
40 – CW – D0190
TRUE OR FALSE? An idle engine oil pressure can drop as low as 5psi, this is a normal condition.
TRUE.
FALSE.
TRUE OR FALSE? If one hinge–pin is broken on the GMT it is FMC?
TRUE.
FALSE.
TRUE OR FALSE? Due to sling capacity, LOADED PAC–3/PAC – 3MSE munitions are always moved one four– pack or two-pack at a time?
TRUE.
FALSE.
Which CM inspects the beam for GMT reload?
CM3
CM2
CM1
CM5
HINT: Highest rank.
TRUE OR FALSE? PAC 3 missiile can be fired on a PAC 2 LS?
TRUE.
FALSE.
What drill number covers PA three prepare for movement?
44 – CW – D0200
43 – CW – D0200
41 – CW - D0200
40 – CW – D0200
What piece of equipment replaced the LMRD on the PAC-3 launching station?
LSDU/J-BOX(Junction box)
KA – band
Fiber optic cables
PMCS
When does time stop for forklift reload?
When the launcher is in remote.
When the launcher is in local.
When the launcher is in road march.
When the launcher is NMS.
What two crew members are interchangeable on GMT reload?
CM4 and CM5.
CM2 and CM1.
CM5 and CM2.
CM1 and CM4.
For decentralized reload, CMs one and two must perform steps ...... through ....... before GMT reload team arrives. REF: 44 – CW – D0161.
Steps 1-6 for decentralized.
Steps 1-7 for centralized.
Steps 2-5 for decentralized.
Steps 1-5 for centralized.
Forks should not extend more than ..... past the edge of the GM canister(s) when being placed on the LS?
6 inches
12 inches
5 inches
7 inches
what does MSE stand for?
Missiile Segment Enhancement
Missiile Segment Exchange
Motor Survival Equipment
Missiile Signal Enhancement
Smoking is forbidden within how many feet of all designated reload areas?
100 feet
115 feet
200 feet
122 feet
TRUE OR FALSE? forklift missiile reload may be performed from the MSA, GMT, or a flatbed–type carrier?
TRUE.
FALSE.
keep hands and feet away from forklift forks to prevent injury. What safety hazard is this?
Warning
Caution
Hazard
all of above.
According to TC 3–01.86, what basic gunnery table do your first conduct reload operations?
Table 3
Table 2
Table 1
Table 4
When performing reload with the GMT either parallel or perpendicular, the GMT should be located ...... to ..... feet away from the launching station?
6-9ft on level of ground.(7–9ft on uneven ground.)
12-15ft on level ground.(10-13ft on uneven ground.
5-10ft on level ground.(7-10ft on uneven ground.)
9-12ft on level ground. (8-13ft on uneven ground.)
During the GMT reload, which crew member is responsible for grounding the missiile with the LS missiile ground cables?
Crew member two
Crew member one
Crew member three
Crew member five
The proper pressure of the fire extinguisher is ..... psi.
150 psi
125 PS
159 psi
135 psi
What is the minimum training site area needed for GMT reload?
20 X 25 m
30 X 35 m
25X 23 m
20 X 23 m
what is the minimum training site needed for a forklift reload?
40 x 50 m
35 x 50 m
40 x 45 m
50 x 60 m
What does the acronym BITE stand for?
Built in test equipment
Built in test enhancement
Built internal test equipment
Break internal test equipment
What drill number covers GMT reload?
44 – CW – D0160
43 – CW – D0260
35 – CW – D0160
16 – CW – D044
TRUE OR FALSE? PAC 3 missiiles can be fired on a M903?
TRUE.
FALSE
When does time start for forklift reload?
When launcher remote key is in local
When launcher remote key is in remote.
When launcher remote key is in enable.
When launcher remote key is in disable.
According to TC 3–01.86, what basic gunnery table do you get evaluated on PMCS?
Table one
Table 2
Table 3
Table 4
What does 44 – CW – D0150 cover
Forklift freeload.
PMCS.
Basic system skills.
Emplacement.
What is the first item checked when conducting AFTER PMCS on the M98384?
Underneath the vehicle.
The rear hub.
The generator.
The outriggers.
Prepare for movement for the PAC3, how long do you have to complete the drill?
25 minutes
30 minutes
15 minutes
20 minutes
During troubleshooting procedures of the 15KW generator, low oil pressure can be caused by....
Air intake not clear.
Low coolant.
All of above.
None of the above.
TRUE OR FALSE? The HEMTT is not considered NMC if the air warning, light illuminates, but the warning buzzer does not operate.
TRUE.
FALSE.
You have a spring assembly that is missing a rubber bumper. IAW the trailer TM, what status code do you place on the DA 5988-e or DA 2404?
X – deadline
/
+
None of the above.
In accordance with TM 9–2 320–3 40–10, what type of air leak deadlines a M983A4 HEMTT?
Any air leak fitting or damage.
Minimum air leak.
No air leak.
TRUE OR FALSE? each launch enable/disable switch is set to enable to prevent inadvertent launch command signals from the ECS when electrical power is applied.
FALSE.
TRUE.
TRUE OR FALSE? once CM2 passes the DLT antenna to CM1, he/she may immediately work on the other task.
FALSE.
TRUE.
How often does the operator conduct preventive maintenance checks and services for the level vial on the gunner's quadrant for cracks, broken, or loose vial, which can cause an elongated bubble.
before, during, and after.
Before and during.
Before and after.
Before.
forklift reload, what does 44 – CW – 0161 cover?
MSE reload
PMCS
basic system skills
GMT reload.
What does 44 – CW – 0190 cover?
PAC 3 placement.
PAC 2 emplacement.
MSE reload.
PMCS.
What does 44 – CW – 0130 cover?
PAC 2 emplacement.
PAC 3 emplacement.
MSE reload.
Prepare for movement.
During a forklift reload, which crew member is responsible for grounding the missiiles with the LS missiile ground cables?
CM4
CM3
CM2
CM5
What does the acronym PBIT stand for?
Power up Build In Test.
Power p Build Intellectual Test.
Power Built In Test
None of the above.
What does 44 – CW – D0140 cover?
PAC2, prepare for movement.
PAC3, prepare for movement.
PAC2, prepare for emplacement.
MSE reload.
If you pull the GMT outrigger lever down, will this raise the outrigger or lower it?
Lower.
Raise.
Level.
What markings are displayed for a canister with live missiiles?
4 inch yellow square in the upper right rear corner and upper left front corner. Live .
4 inch brown square in the upper right rear corner and upper left front corner.empty.
6 inch yellow square in the upper right rear corner and upper left front corner.live.
6 inch brown square in the upper right rear corner and the upper left front corner.Empty.
TRUE OR FALSE? during PAC-3 missiile selectability you are permitted to put the launcher in remote.
FALSE.
TRUE.
if GMT is out of level more than 5°, un-level indicator will light (yellow) and buzzer will sound. Use of crane in unleveled position may cause GMT to tip over and cause personal injury and damage to equipment. What hazard is this?
Caution
Warning
Hazard
What drill number covers GMT reload?
44 – CW - D0200
44 – CW – D0100
41 – CW – D0100
40 – CW – D0200
TRUE OR FALSE? it is permitted to leave live PAC-3 missiile canisters ungrounded for up to four hours as long as you have a deliberate risk assessment signed by the Battery Commander.
FALSE.
TRUE.
What drill number covers Pac 3, prepare for movement?
44 – CW – D0200
41 – CW – D0200
40 – CW – D0110
45 – CW – D0200
The MRCTS takes about ...... seconds to go from step 00 to 99?
60 seconds
50 seconds
Two minutes
90 seconds
Paperwork showing that a valid and current load test has been performed within the last .... must be hand before any reload operation can be conducted.
12 months
6 months
8 months
2 months
What are the three reload configurations?
Perpendicular.
End to End.
Parallel.
Diagonal.
What are the three positions for the engagement control handle?
Rotate, elevate, road march.
Rotate, local, remote
Enable, disable, local.
Rotate, elevate, local.
What is the travel speed for ground guarding the forklift?
Walking pace of ground guide
5 mph
7 mph
10 mph
If you pull the GMT crane lever to the max, will this speed up the crane or slow it down?
Speed up.
Slow down.
Stay the same.
None of the above.
Define the alert states of AS1,AS2,ASC, and AS4?
(a)
Define the Alert State of AS5,AS6AS7, and AS0
(a)
What is patriot power
120/208 vac 3 phase 4 wire 400hertz 15kv.
110/135 vac 2 phase 4 wire 330hertz 15kv.
120/208 vac 2 phase 4 wire 404 hertz 15kv.
