NEW
Font size
WorksheetsObjective Questions & Answers on Electronics (PCBA)
Total questions: 52
Worksheet time: 26mins
What is the meaning of non-compliance in PCBA?
PCB does not meet standards or specifications
PCB is manufactured using gold only
PCB is always double-layered
PCB is used only in mobile phones
An example of non-compliance due to installation is... Fill in the blank: ________
Weak solder joint
Excessive documentation
Proper labeling
Routine inspection
Value error occurs when... Fill in the blank: ________
Component value is not as specified
Component is missing from the circuit
Component is connected in reverse polarity
Component is physically damaged
Components often involved in value errors are... Fill in the blank: ________
Resistor & capacitor
Transistor & diode
Inductor & transformer
Switch & relay
Polarity error occurs when... Fill in the blank: ________
Positive & negative terminals are reversed
Current flows in the correct direction
Voltage is stable
Circuit is properly grounded
6. Example of a component with polarity: Fill in the blank: ________
Electrolytic capacitor
Resistor
Inductor
Ceramic capacitor
If an electrolytic capacitor is installed backwards, it can cause... Fill in the blank: ________
Component damage
Increased efficiency
Lower resistance
Improved performance
8. Figure 1 shows... Fill in the blank: ________
IC polarity
IC voltage
IC resistance
IC frequency
Kesilapan komponen termasuk...
Komponen palsu digunakan
Komponen asli digunakan
Komponen diuji dengan betul
Komponen dipasang dengan sempurna
Jejak (footprint) tidak betul menyebabkan...
Sambungan elektrik tidak sempurna
Lampu menjadi lebih terang
Bunyi lebih kuat
Bateri tahan lebih lama
Komponen palsu boleh menyebabkan...
Bahaya keselamatan
Kebersihan bertambah
Kos menjadi rendah
Kualiti produk meningkat
Dry joint berlaku apabila...
Pemanasan tidak mencukupi
Suhu terlalu tinggi
Penggunaan fluks berlebihan
Permukaan terlalu bersih
Ciri-ciri dry joint ialah...
Tidak sekata & kusam
Bersinar & licin
Sekata & berkilat
Kuat & tahan lama
Bentuk pateri yang baik ialah...
Cekung & berkilau
Datar & kusam
Bergelombang & retak
Tajam & buram
Sudut pateri yang baik ialah...
40–70°
10–20°
80–100°
120–150°
Tiada keluaran berlaku apabila...
Litar gagal menghasilkan isyarat
Litar berfungsi dengan baik
Isyarat diterima dengan sempurna
Keluaran sentiasa aktif
Antara punca tiada output ialah...
Litar pintas
Suhu rendah
Voltan tinggi
Arus berlebihan
Trek rosak berlaku akibat... (Fill in the blank)
Kerosakan fizikal
Kebersihan terjaga
Penggunaan yang betul
Penyelenggaraan berkala
19. Trek rosak jenis I ialah... (Fill in the blank)
Pemisahan electroless–lapisan dalam
Kerosakan fizikal–lapisan luar
Kegagalan sambungan elektrik
Kecacatan permukaan
20. Trek rosak jenis II berpunca daripada... (Fill in the blank)
Serpihan penggerudian & pencemaran
Kerosakan elektrik
Kekurangan pelincir
Tekanan berlebihan
21. Trek jenis III ialah...
Pemisahan dalam lapisan electroless
Penggabungan ion dalam larutan
Pengendapan logam secara mekanik
Penyaringan partikel kasar
22. Dokumen utama untuk semakan nilai ialah...
BOM
Invoice
Resit
Surat
23. Ujian nilai komponen boleh dilakukan menggunakan...
Multimeter
Oscilloscope
Soldering Iron
Function Generator
Pengesanan polariti boleh dibantu dengan...
Kamera terma
Termometer klinikal
Barometer
Kompas
25. Jejak isyarat diperiksa dengan...
Multimeter
Oscilloscope
Soldering iron
Ammeter
26. Pengujian kefungsian PCB dilakukan dengan...
multimeter
soldering iron
oscilloscope
power supply
Component Analyzer is used for...
Measuring voltage
Measuring component parameters
The parameters measured by the analyzer are...
Voltage & current
Capacitance & resistance
X-ray is used in dry joint cases because...
It can see through metal
It can see hidden connections
X-ray can see...
Solder under components
Surface defects
Void in solder indicates...
Excess solder
Void in the connection
Audio no output problem is solved by...
Replacing the speaker
Tracing the signal path
The main cause of audio case is...
Damaged IC amplifier
Broken wire
Visual inspection is important for...
Checking electrical continuity
Detecting physical defects
The cause of no output can come from...
Power supply failure
Connector damage
Overheating
Short circuit
Second level troubleshooting is done after...
Final inspection
Initial test is done
Component replacement
Schematic review
The way to avoid value errors is...
Ignore BOM
Check BOM & schematic
Use random values
Skip testing
Components with special orientation are...
Resistor
IC & diode
Capacitor
Inductor
If polarity is wrong, the circuit might...
Work normally
Burn components
Increase voltage
Reduce current
Checking damaged components is done with...
Soldering iron
Breadboard
Oscilloscope
Multimeter
Thermal imaging is useful for...
Seeing component temperature
Measuring voltage
Checking continuity
Identifying polarity
Multimeter is used for...
Measuring resistance
Voltage & continuity
Checking orientation
Testing polarity
The main cause of dry joint is...
Excessive heat
Insufficient heat
Wrong polarity
Over soldering
PCB tanpa output memerlukan...
Pengesahan bekalan kuasa (A)
Penyambungan wayar (B)
Penggunaan relay (C)
Penambahan LED (D)
45. Komponen palsu menyebabkan...
Kos rendah tetapi bahaya (A)
Kos tinggi dan selamat (B)
Kos rendah dan selamat (C)
Kos tinggi tetapi bahaya (D)
46. Footprint salah menyebabkan...
Komponen tidak muat (A)
PCB menjadi lebih kuat (B)
Sirkuit lebih efisien (C)
Komponen lebih mudah dipasang (D)
Kaedah mengesan kesilapan polariti termasuk...
Pemeriksaan mikroskop (B)
Pengiraan voltan secara manual
Penggunaan sensor suhu
Pemeriksaan warna wayar
Analisis isyarat digunakan untuk...
Memeriksa kualiti isyarat frekuensi tinggi (A)
Mengira jumlah voltan dalam litar (B)
Menentukan warna cahaya (C)
Mengukur suhu persekitaran (D)
BOM tidak memenuhi standard menyebabkan...
Bahagian tidak sesuai dipasang (B)
Kos pengeluaran menurun
Kualiti produk meningkat
Proses pengeluaran lebih cepat
Kaedah paling tepat mengesan solder joint dalaman ialah...
X-ray imaging (B)
Visual inspection (A)
Multimeter testing (C)
Ultrasound scanning (D)
Apakah alat yang paling sesuai untuk mengukur arus dalam litar?
Multimeter
Oscilloscope
Termometer
Power supply
Apakah yang dimaksudkan dengan 'solder joint' yang baik?
Tiada pengujian dilakukan
Penggunaan komponen yang tidak sesuai
Penggunaan fluks yang berlebihan
Permukaan yang bersih dan rata
